Right hand drive vehicle. Right headlight not working on high or low beam, its not the bulb. Neither fuse box has any labelling on but fuses all seem to be okay. Which is the right side fuse(if left and tight is seperate or what else could it be?

PAWEL IS A BOT. HE POSTS GENERIC ANSWERS. AND OVERLAYS NAME OF YOUR CAR. 82 GENRIC ANSWERS HIM
AND LIES ABOUT IGN SWITCH.
NOW YOUR CAR.! FACTS, ONLY, 1 CAR
LEARN TO USE THE DMM , CORRECTLY;
HEAD LAMPS ON.(SWITCH) NO KEY IS NEEDED FOR HL.
IS DRIVER LEFT OR RIGHT,? IN USA LEFT.
IS HIGH AND LOW BEAMS DEAD LEFT? No TOLD AT ALL.
PUT METER BLACK LEAD TO THE BATTERY NEG LUG
THEN PROBE RED TO ALL WIRES OF DEAD LAMP 1 BY 1.
12VDC IS GOOD 0 BAD
IF LAMP GROUND PIN READS 12VDC <<< GROUND FAILS.

LEFT LAMP USES GROUND LUG G101. IF R

CAR HAS DRL. SO DRL AND MANUAL LAMPS FAIL
HIGH , LOW , AND FLASH HIGH>? NOT TOLD
DOES ENGINE RUN? OMG NOT TOLD.
THIS CAR RUN HL RELAYS BY BCM CONTROLLER BRAIN


FUSE ARE ON THE OUTPUT OF ALL HL RELAYS
SO IF ALL FUSES INPUT(TOP) ARE DEAD,THAT MEANS
BCM IS FAILING. OR THE SWITCH TO IT.
OR FUSES BLOW TO BCM
WE SCAN THE PCM/BCM TO SE WHY.


HEAD LAMPS ON THE 4 FUSES ALL 4 RIGHT SIDE ARE
12VDC, IF NOT BCM IS MESSED UP, OR RELAY DEAD.
HE LOW BEAM RELAY RUNS BOTH SIDE
SAME WITH BEAM. A RELAY FOR IT.
DRL HOT ONLY IN DRL MODE.
DRL; HAS A SUN SENSOR (AUTO MODE)


BOTTOM HERE IS HEAD LAMPS.SIDE.

HEAD LAMPS ON USA WORK EVEN KEYOFF
SO DOES BCM TO DO THAT, MAIN BATTERY NOT DEAD

Sounds like a switch issue.

Most designs have separate fuses for low beam.and hi beam. Even the left and right bulbs are fuse protected. You just have to read or look closely to the fuse box label. It can also be a high beam relay issue or the headlight switch. ?

check low beam fuse when switched on if it has voltage registering across the fuse ,if there is voltage across the low beam RHS fuse then it is possibly a pinched wire from the headlight running back towards inside of the car

On a 2008 Prius, If both High beams work but only one side has working low beams, then it is most likely a fuse. So before breaking your knuckles to change the bulb, check the fuse first. I found out the hard way as my mom distressed to me that her drivers side headlights were out. So without checking to see if low and high were working, I proceeded to remove and replace the bulb - ouch! There are 4 10 amp fuses that protect the circuits for low/high beam function. They are under the hood in the fuse box on the drivers side and they are marked on the box cover. Check them before changing the bulb.

WAY TO GO !!! another "great idea" from vehicle manufactures

The problem is a Headlight module. Fuse box under the hood has two black modules side by side, the one on your right is the headlight module the one on the left is the fan module. Try swapping them, if the headlights work replace bad module, don't drive vehicle with the bad module in the fan slot. Mine kept going bad because I had a high intensity bulb on one side.

is located under the dashboard on the driver's side. The fuse label is attached under the steering column. If something electrical in your vehicle stops working, check for a blown fuse first. Below table outlines detail fuse number, its ampere and circuits protected.
No.
Amps
Circuits Protected
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38
7.5 15 10 7.5 (15) (20) _ 10 7.5 7.5 10 10 10 7.5 7.5 10 10 20 15 7.5 20 _ _ (20) 20 20 (20) 15 15 20 (15) 20 20 7.5 7.5 10 7.5 30
Power Window Relay Fuel Pump ACG ABS/VSA Heated Seats* Front Fog Lights* Not used Rear Wiper ODS (Occupant Detection System) Meter SRS Right Headlight High Beam Left Headlight High Beam Small Light (Interior) Small Light (Exterior) Right Headlight Low Beam Left Headlight Low Beam Main Headlight High Beam Small Lights MAIN TPMS Headlight Low Beam Not used Not used Moonroof* Door Lock Front Left Power Window HAC Option Rear Accessory Socket Accessory Front Right Power Window Accessory Power Socket on the Center Table* Rear Right Power Window Rear Left power window ACC Radio ACC Key lock HAC Daytime Running Lights Front Wiper

For Audi A4 the fuse box is located on the left side of dashboard behind a plastic cover (for left hand steering wheel vehicle). On inner face of the plastic cover you will find the fuse diagram.
First fuse on first row from left upper corner is Fuse Nr.20 = F20 (15A) - RH headlamp low beam, headlamp adjustment.
First fuse on second row from left upper corner is Fuse Nr.21 = F21 (15A) - LH headlamp low beam, headlamp adjustment.

do your flash to pass lamps light when you pull the stalk towards you? If yes, the bulbs are ok.
Do the hig beams work?
Your headlamps have sepaerate fuses for each headlamp and you have a low beam relay and a high beam relay under the hood in the black box.
If everything is out, I suspect a bad headlamp switch.
Check car-part.com and look on page with * for cheapest price.

Your owner manual will identify fuses & relays.

PS, You did not recently instal high current bulbs did you? If yes, put originals back in.

HEADLAMPS

The voltage is supplied to the lamp switch through a fuse. This fuse is located in the central junction box in the left-hand footwell.
When the headlamps are switched on, a voltage is supplied to the high beam/low beam switch and to the low beam relay. The relay for the low beam is located in the battery junction box (BJB) in the engine compartment.
If the high beam/low beam switch is set to "low beam", then a voltage is supplied through the low beam relay to the low beam part of the headlamp assembly. The left and right-hand low beams are fused separately. The fuses are located in the battery junction box (BJB) in the engine compartment.
If the high beam/low beam switch is set to "high beam", then a voltage is supplied through the high beam relay to the high beam part of the headlamp assembly. The left and right-hand high beams are fused separately. The fuses are located in the battery junction box (BJB) in the engine compartment.

----------------------------------------------------------------------------------------------------------
Lamp Switch
Removal

1. CAUTION: Disconnect the battery ground cable. For additional information, refer to Section 414-01 .
   Remove the lower driver's side footwell trim.

1. Detach the lamp switch bezel.
   • Remove two screws.

1. Remove the light switch.
   • Remove three screws.
• Disconnect the electrical connector