Question about 2004 Pontiac Grand Am

1 Answer

What size are the bolts that mount the hood on a 2004 pontiac grand am?

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has answered 20 questions.

  • Expert
  • 111 Answers

10 12 or 13 milimeter metric

Posted on Sep 13, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

2004 Pontiac grand am fender replacement

remove all of the inner fender bolts under the hood and in the wheel well - you should be able to take it off very easily

Jul 02, 2015 | Pontiac Cars & Trucks

1 Answer

How do you change a heater line elbow on a 2004 Pontiac Grand Prix ?

This must be a 3.8 liter engine. They have 2 plastic elbows that always break they run threw the alternator mounting bracket. #1 disconnect battery #2 remove serpentine belt by unloading tensioner . #3 remove alternator and mounting bracket this needs to be pried away from cylinder head remove broken pieces and clean passage bores install new elbows with some vasoline on o-rings and align then reassemble. one elbow comes from intake manifold both sides are the same size the other comes from timing cover near water pump the lager side goes into timing cover.

Aug 19, 2014 | 2004 Pontiac Grand Prix

1 Answer

Thread size needed for a 1997 grand am rear wheel hub assembly

take out a close bolt (same area)and take it to a bolt /fastener shop. They will be able to measure the size and thread and will supply a bolt to the correct grade requirement;

Dec 25, 2013 | Pontiac Cars & Trucks

1 Answer

What size socket do I use to remove the brake caliper on a 2004 grand prix?

the caliper to slide bolt can be a 13, 14 or 15mm. The caliper bracket to knuckle bolt is usually a 15mm but can also be an 18mm

Feb 03, 2012 | 2004 Pontiac Grand Prix

1 Answer

What kind of oil for a 2004 pontiac grand am

First question is what engine size? My 2004 has a v6 and it takes 5w 30 and it has that specification on the oil filler cap under the hood in yellow letters. I recommend checking your owners manual to confirm. Not sure about 4 cyl.

Nov 07, 2011 | 2004 Pontiac Grand Am

1 Answer

How to replace battery 2004 grand prix

you have to take off your engine cross member that is over the top of your battery and than disconnect your battery. There is 2 bolts on the bottom that hold your battery to the mount unbolt those and it should come right out

Dec 08, 2010 | 2004 Pontiac Grand Prix

1 Answer

Dimensions of starter mounting bolts for a 1992 pontiac grand prix se 3.1L


Oct 20, 2010 | 1992 Pontiac Grand Prix

1 Answer

How to replace 1996 pontiac grand am motor mount

On 96 Grand Am 2.4L you have to remove the motor mount first to get the top 2 transaxle bolts on the mount bracket removed. The bracket and trans mount are removed as one unit after all 8 bolts are removed. You will need a 3 foot bry bar to move the engine over to the side as far as possible to make room for the 2 top bolts to be removed.

Sep 12, 2010 | 1996 Pontiac Grand Am

2 Answers

2004 pontiac grand prix serpentine belt replacement/ routing

first look underneath the hood... is it there on a sticker... if not i'll need the size of the motor to let you know


Jan 27, 2009 | 2004 Pontiac Grand Prix

2 Answers

2004 Pontiac Grand Am SE1 loud noise

It is probably the wheel bearings they have been known for that.

Oct 26, 2008 | 2004 Pontiac Grand Am

Not finding what you are looking for?
2004 Pontiac Grand Am Logo

Related Topics:

38 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts


Level 3 Expert

79077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides