Question about 1992 Ford Ranger

1 Answer

92 ford ranger have no spark replaced both coils ignition module crank sencer coputer still have no spark anything i can try

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 111 Answers

Check your ground cable at battery very critical on this one

Posted on Sep 13, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1987 Ford Ranger 2.9 crank / no start. Does tachometer function somehow affect the spark timing?


No, but the tach signal may help you determine if coil is getting signal to spark. If tach needle is moving when engine is cranking over, that means the coil primary circuit is being turned on and off, and that means the ignition control module is working.

Oct 24, 2017 | 1987 Ford Ranger

1 Answer

Both coils do not fire on 1 and 4. Will start but only running on 2 cylinders. Could both coils be bad or should I look elsewhere?


Part 3 -How to Test the Ignition Module and Crank Sensor ...

easyautodiagnostics.com > Ford > 2.3L
Mar 1, 2012 - Spark plugs for cylinders #2 and #3 get spark at the exact same time. ...voltage -12 Volts) to both individual ignition coils within the coil pack. ... Ford Mustang or Ranger (or 2.3L Mazda B2300), this is what you'll need ... for this 'Switching Signal' at the coil pack... but you can also test this ... 1991, 1992, 1993.

How to Diagnose a Misfiring Cylinder (2.3L Ford Ranger ...

troubleshootmyvehicle.com > Ford > 2.3L
Apr 3, 2012 - Bad Fuel Injectors can cause a Misfire Condition. ... the ignition system on the 2.3L Ford Mustang or Ranger consists of 2 ignition coil packs, ...

2002 ranger misfire rough idle - Discussion on Topix

www.topix.com > Ford Ranger
Jul 27, 2007 - My truck is giving the code misfire in number 4 cyl. I replaced my spark plugs, Wires, Coil packs (both of them) and all my fuil ... three (3.0L v6) go bad, the fuel/air mixture gets messed up. Judged: 2. 2 ... My truck runs rough only at idle. ...code for ford ranger 2002, 2.3 5speed. truck runs like a champ but that ...

Extremely stumped! I need the best and brightest 1994 Ford ...

answers.edmunds.com > Edmunds Answers

Jan 31, 2016 | Cars & Trucks

1 Answer

3.0l. Where is ignition control module located?


The coil and ignition module are part of same assembly, follow the spark plug wire, spark plug on one end, coil/ignition module on the other end.
I was going to ask, how long since a tune-up? Are there any applicable trouble codes? Are missing anything besides spark? Did you check primary voltage at the ignition module? That is a fused circuit.

Dec 27, 2012 | 1999 Ford Ranger SuperCab

1 Answer

Wheres is the crank sensor for a 1987 ford ranger 2.3l 4x4 4cylinder


This truck uses a distributor, so the job of crank - cam sensors is handled by the pick-up coil in the dist.
Is the coil and module getting power from the EEC relay ?

Jul 04, 2012 | Ford Cars & Trucks

1 Answer

1992 ford ranger will not crank- the starter will turn it over but never start. when i trung the key can hear the fuel pump turn on - added fuel still nothing . been a great truck since 92- what do i need...


Check for spark. No spark can be from the coil, igntion module, crank sensor. Have the codes check, this will at least point you in the right direction.

Feb 05, 2011 | 1992 Ford Ranger

1 Answer

No spark-coil and ignition module check ok, there is power at the coil


Try looking for the crank sensor. It is located on the tranny bell housing. With out this senor the vehicle will not spark or send a signal to the coil for a spark. Its not a easy job to replace but I belive this could be your problem.

If I can help more please feel free to ask!

Joe

Oct 15, 2010 | 1987 Ford Ranger

1 Answer

1994 ford ranger 2.3litter timming belt broke replaced it know i have no spark and no fuel pump does the crank sensor do that


Yes, if the ignition module doesn't receive the signal from the crank sensor it won't send fire to the coils or the signal to the ecm to run the fuel pump.

Apr 22, 2010 | 1994 Ford Ranger Supercab

1 Answer

1987 Ford Ranger. Won't fire.


Ignition module comes to mind. If you've tested for spark (holding spark plug wire near the block when cranking) and the cap and rotor are good, it seems the module is the only other area left to try. Best of luck Patrick. Please post back with any other questions.
Greg

Jun 12, 2009 | 1987 Ford Ranger

Not finding what you are looking for?
1992 Ford Ranger Logo

Related Topics:

166 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

79847 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

fordexpert

Level 3 Expert

5685 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...