Question about 2001 Chrysler LHS

1 Answer

The ABS pump continues to run after the car has been completely turned off.

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 376 Answers

Air in the system can cause thic problem as well as faulty electronics in the unit, clogged line in unit placing back pressure on the solinoid......? take your pick

Posted on Sep 13, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

What would cause the ABS module to run continuously?

Most likely the ABS module is bad. Replaced many. Just a few times is was the ground for the pump.

Oct 30, 2015 | Cars & Trucks

1 Answer

My abs light goes on and off, sometimes it doesn't come on at all,when it is cold it usually takes longer to turn on. Can any body help?

brakes will continue to work, but your abs pump is probably going bad and your car will lock the wheels when brake is pressed, if that's the case; abs pumps are not cheap.

Dec 10, 2014 | 2001 Isuzu Trooper

1 Answer

Why won't abs light go off error code says pump

When a pump code comes on for the abs it is usually associated with the module connected to the pump. Most of the time either the relay controlling power to the pump loses it's continuity on the board or the connector builds corrosion and resistance in the terminals. Most of the time depending on the make and model an the exact code it can be remedied by purchasing a new or used abs module/ pump, repairing the old module/ pump, or just replacing with a new module/ abs pump(most expensive option). It is very common for abs relay/ pump codes to appear and end up relating to the power or ground circuit going to open( breaking continuity it frying a connection form resistance)

Jun 05, 2014 | Chrysler Voyager Cars & Trucks

1 Answer

I changed the rear brake calipers on my 2000 chevy Z71 i get oil out of both after bleeding but brake peddle still is spongy

Ok many people have this problem when they do brakes that ABS equiped. First of all make sure that all your connection are tight at the calipers. Check and make sure you have no visible leaks at all every where on the vehicle. Second alot of people do not know that the vehicle must be running when you bleed the brakes when the vehicle has ABS brakes. So the solution to your problem is very simple check to make sure master cylinder is full, then start your vehicle and have some one pump the brakes then hold down and open bleeder valve. You need to do this several times with ABS brakes,make sure you continue to check master cylinder fluid level continuously. Always start bleeding the brake that is farthest away from master cylinder first then continue to work your way to the closesest. Remeber when bleeding brakes when equiped with ABS the vehicle must be running to allow the ABS pump to run and bleed as well.

May 11, 2011 | 2000 Chevrolet Silverado 1500

1 Answer

2004 ford ranger when brakes applied makes sound like a pump running ABS and BRAKE indicator lights are on.

the sound u hear is the abs pump.for the lights to be on and hear the pump running, there is a problem, take it to shop before brakes fail completely

Dec 14, 2010 | 2004 Ford Ranger

3 Answers

Mechanic say that ABS pump is bad and that only the dealer can repair it. The pump wont shut down and drained the battery overnight

wow.. i think..your mechanic is from some old school before they used igintion switches.. when you turn you key off.. it should stop all current going to coming from your battery. try crawling under you truck and spray an rust cleaner like wd 40 on the inside of you wheels .. use more than you think you should as it sounds like you have a rusted wheel sensor on one or more of you wheels..

Feb 26, 2010 | 2001 Chevrolet Blazer

1 Answer

Anti lock brake pump always running and noisy

If the ABS pump continues to run, the most common cause is a leak in the hydraulic control unit. The pump may continue to run in order to to try to maintain operating pressure. Also a malfunction in the pump, stuck valves and devective accumulators are possible causes. A shorted pressure switch may also cause this condition.

Jul 09, 2009 | 2001 Chevrolet Tahoe

3 Answers

Where is the abs control module located on a 02 chevy avalanche ?

THE EBCM IS BAD this is the electronic control module that is on abs pump. you can replace seperate I think it is around 500 for part

Dec 30, 2008 | 2002 Chevrolet Avalanche

1 Answer

ABS light and pump

after you took the fuse out and it stopped did you put the fuse back in and see if it continued to run?

Sep 02, 2008 | 2002 GMC Yukon XL

Not finding what you are looking for?
2001 Chrysler LHS Logo

Related Topics:

64 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts


Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides