Question about 1996 Ford F150 Regular Cab

1 Answer

Installed a new water pump and is leaking. - 1996 Ford F150 Regular Cab

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

Did u put new gasket and if so might want to put some rtv gasket maker

Posted on Sep 13, 2009

Testimonial: "You're right. Used sensor safe and corrected the problem. Thanks for the response"

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

New water pump now leaking


Are you sure the new pump is leaking or is there something else causing the leak. Who replaced the water pump? There should be warranty.

Aug 02, 2015 | Cars & Trucks

1 Answer

Need to replace the waterpump.


Hello, 1)Put sealing compound onto a new water pump gasket. Place the new water pump and new water pump gasket onto the cylinder block.
2)Connect the three bolts to the water pump and tighten them to between 15 to 22 feet lbs.
3)Reconnect the heater hose to the new pump. Install the water pump belt onto the pulley, making sure to adjust the tension on the belt.
4)Place a new o-ring onto the water pump inlet and install it, tightening the bolts to 7 feet lbs.
5)Close the draincock on the radiator.
6)Install the water pump pulley onto the drive belt, adjusting the tension on the belt.
7)Reconnect the negative battery cable.
8)Refill the cooling system with coolant to the proper levels. Start the engine and check for leaks when the engine reaches normal operating temperatures.
Thanks

Jun 17, 2011 | 1999 Ford Taurus

1 Answer

I need to know how to replace a water pump on a 2002 hyundai gx 350.


2002 Hyundai XG350 3.5L MFI DOHC 6cylWater Pump - Removal & Installation
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Drain the cooling system.
  3. Remove or disconnect the following:
    Negative battery cable Accessory drive belts Water pump pulley Timing belt, tensioner and idler pulley Water pump

  4. 1514f36.jpg

    Fig. Water pump assembly-XG 300 and XG 350 (click over pic for zoom)

To install:
  1. Clean all mating surfaces of any residual gasket material.
  2. Install or connect the following:
    Water pump with a new gasket and torque the bolts to 16 ft. lbs. (22 Nm) Tensioner and timing belt and idler pulley Water pump pulley and drive belts Negative battery cable
  3. Fill the cooling system to the proper level.
  4. Start the vehicle, check for leaks and repair if necessary.
To install:
  1. Clean all mating surfaces of any residual gasket material.
  2. Install or connect the following:
    Water pump with a new gasket and torque the bolts to 16 ft. lbs. (22 Nm) Tensioner and timing belt and idler pulley Water pump pulley and drive belts Negative battery cable
  3. Fill the cooling system to the proper level.
  4. Start the vehicle, check for leaks and repair if necessary.

95486b3.jpg


Fig. Water pump bolt lengths-3.5L engine

Install the water pump with new gaskets and O-rings. Tighten the bolts to the following specifications:
  1. 1.5L SOHC engine: 105-132 inch lbs. (12-15 Nm).
  2. 1.5L DOHC engine: 14-20 ft. lbs. (20-27 Nm).
  3. 1.6L DOHC engine: 14-20 ft. lbs. (20-27 Nm).
  4. 1.8L, 2.0L, and 2.4L engines: 14-20 ft. lbs. (20-27 Nm).
  5. 2.5L engine: 11-16 ft. lbs. (15-22 Nm).

Hope helps (remember rated this).

Jun 18, 2010 | 2002 Hyundai XG350

1 Answer

Change water pump on 1999 Century Buick


GM Century/Lumina/Grand Prix/Intrigue 1997-2000 Water Pump - REMOVAL & INSTALLATION

3.1L and 3.4L (VIN E) Engines
  1. Disconnect the negative battery cable.

  2. Partially drain the cooling system into a suitable container.
  3. Remove the drive belt guard.
  4. Loosen the water pump pulley bolts before removing the drive belt. This should help keep the pulley from turning as the bolts are loosened.
  5. Remove the drive belt. Please see .
  6. Remove the water pump pulley bolts and remove the pulley.
  7. Remove the water pump bolts and separate the pump from the engine front cover.

To install:

1430070.jpg

Fig. Exploded view of the water pump and front cover arrangement-3.1L and 3.4L (VIN E) engines
  1. Clean all parts well. Use care when scraping gasket material from the front cover and the pump. Do not gouge aluminum parts. Clean the bolt threads well. The torque specification is low and if the bolt threads are dirty, an accurate torque is not possible and leaks are likely to develop.
  2. Using a new gasket, install the water pump to the front cover. Install the cleaned and lightly lubricated water pump bolts. Torque to 89 inch lbs. (10 Nm).
  3. Install the water pump pulley and bolts and torque to 18 ft. lbs. (25 Nm).
  4. Install the remaining components in the reverse order of the removal process. When refilling the cooling system, use the proper mix of DEX-COOL® and water. Check for leaks.

3.4L (VIN X) Engine
  1. Disconnect the negative battery cable.
  2. Partially drain the cooling system into a suitable container.
  3. Remove the coolant recovery reservoir.
  4. Remove the drive belt. Please see .
  5. Remove the pulley bolts and separate the pulley from the water pump.
  6. Remove the water pump bolts and remove the pump from the engine.

91d51fb.jpg

Fig. Exploded view of the water pump mounting-3.4L (VIN X) engine
To install:
  1. Clean all parts well. Use care when scraping gasket material from the front cover and the pump. Do not gouge aluminum parts. Clean the bolt threads well. The torque specification is low and if the bolt threads are dirty, an accurate torque is not possible and leaks are likely to develop.
  2. Using a new gasket, install the water pump to the front cover. Install the cleaned and lightly lubricated water pump bolts. Torque to 89 inch lbs. (10 Nm).
  3. Install the water pump pulley and bolts and finger-tighten the bolts.
  4. Install the drive belt, then torque the pulley bolts to 18 ft. lbs. (25 Nm).
  5. Install the remaining components in the reverse order of the removal process. When refilling the cooling system, use the proper mix of DEX-COOL® and water. Check for leaks.

Hope this help (remember comment and rated this).

Apr 04, 2010 | 1998 Buick Century

1 Answer

How do i change the water pump on a 1999 2.5 v6 chrysler sebring?


Hello,

Removal:
Drain cooling system, remove the timing belt if necessary. Remove water pump mounting bolts. Separate water pump from water inlet pipe and remove.

Inspection:
Replace water pump if it has damage or cracks to pump body. Check the shaft seal for any leaks as evidence by traces of coolant from vent hole. Check for any impeller rubbing inside pump, and for loose or rough bearings.

Installation:
Clean all gasket and "O" ring surfaces. Install NEW "O" ring on water pipe (wet "O" ring with water to aid assembly). DO NOT allow oil or grease to contact "O" ring. Install NEW gasket on water pump, and install pump inlet opening over water pipe. Install pump-to-block bolts and tighten to specification 18 FT. Lbs. (25n.m). To complete installation, reverse removal procedure.

Hope this helps :)

Oct 19, 2009 | 1998 Chrysler Sebring

1 Answer

I need directions to change my water pump


drain engine coolant.relieve belt tension .and remove the drive belt.remove upper fan shroud.remove fan or fan and clutch assembly.remove water pump pulley and coolant hoses from water pump.remove water pump bolts.then remove pump from engine.pay attention to bolts location because they are different lenghts.clean water pump gasket mounting surface dont scratch .or pump gasket wont seal and leak .apply sealant to water pump bolts.install water pump with new gasket.if gasket paper put a sealant on it.torque water pump bolts to 30 ft lbs.if you got a 2.2L engine torque water pump bolts to 18 ft lbs.install coolant hoses on pump .install water pump pulley.install fan and fan clutch assembly.install the drive belt .and the upper fan shroud.fill the radiator with coolant.then run engine to check for leaks.WARNING AS A SAFETY PRECAUTION REMOVE NEGATIVE BATTERY CABLE SO CAR WONT BE CRANK BY ACCIDENT. ALSOOOO DONT FORGET TO TURN OFF RADIO FIRST BEFORE DISCONNECTING BATTERY SO YOU WONT LOSE YOUR RADIO CODE.

Jun 01, 2009 | 1999 GMC Jimmy

1 Answer

Replaced water pump for the 5th time and it leaks from the hole u


No , it's not normal to leak.
Either , water pump is bad ( 5 times ? )
or instalation was bad or more likely , leak is not the water pump at all

May 09, 2009 | Ford SVT Cars & Trucks

Not finding what you are looking for?
1996 Ford F150 Regular Cab Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5522 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...