Question about Toyota Land Cruiser

Open Question

How do you fold the front window down - Land Cruiser Toyota Cars & Trucks

Posted by on

  • kerry littleton May 11, 2010

    +what year ?what model ?

×

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

07 corvette top will retract but deck lid makes no effort to close, then top will not go back up. Need to release pressure in block lift top up about 1/4 of way then top will go back up


Manually Moving the Folding Top from the Down Position
Important: Allow the system a minimum of four minutes to bleed down pressure after the last cycle.
Manually release the folding top cover latch using the emergency release cable.
Raise the folding top stowage cover.
Manually raise the folding top, holding the 5 bow up.
Manually lower and latch the folding top stowage cover.
Manually unfold the top and latch per normal procedure.

Manually Moving the Folding Top from the Up Position
Important: Allow the system a minimum of four minutes to bleed down pressure after the last cycle.
Manually release header latch per normal operation.
Manually lift front of roof off of the header and raise the #5 bow at the same time.
Manually release the Folding Top Cover latch using the emergency release cable.
Fold the roof down into the well.
Manually close and latch the folding top stowage cover.

Power Folding Top System Components
The power folding top system consists of the following components:
• Folding top control (FTC) module
• Body control module (BCM)
• Folding top control switch
• Serial data communication
• Folding top cover latch actuator
• Folding top cover pull down actuator
• Folding top pump motor with valve manifold
• Position switches and limit switches:
- Pin receiver switch
- Luggage barrier switch
- Folding top cover open switch
- Top open switch
- Top closed switch
- 5 bow raised switch
- 5 bow lowered switch
• Tonneau release relay
• TONNEAU PULL DOWN ACTUATOR Fuse 20 A
• TONNEAU RELEASE Fuse 10 A
• BATT 2 Fuse 40 A
• REAR FOG/ALDL TOP SW Fuse 10 A
• Folding top mechanical components:
- Folding top
- Folding top cover
- Folding top valve 1
- Folding top valve 2
- Folding top valve 3
- Hydraulic lines and cylinders

Folding Top Cover Latch Actuator
The power folding top system includes a folding top cover that is powered open and close by a hydraulic system that is controlled by the FTC module. A power unlatch motor is used to unlatch the folding top cover before the folding top control (FTC) module powers the top cover open. The folding top cover unlatching is requested by the FTC module via class 2 message, but is executed by the body control module (BCM). When requested, the BCM applies battery voltage through the folding top cover release relay control circuit to the tonneau release relay. The relay is energized and battery voltage is applied through the folding top cover release control circuit to the latch actuator. The actuator is energized and the latch releases the folding top cover.

The electronics on this are very complex ,

System Operation
Before any movement of the power folding top is allowed, the folding top control (FTC) module must be aware of the following conditions:
• Unlatch the header. The FTC module reads the pin receiver switch is Inactive.
• The windows must be normalized. Refer to Power Window Reinitialization.
• The ignition must be placed in Accessory or RUN.
• The transmission must be placed in PARK, or with manual transmission, the park brake must be applied.
• Trunk status must not be ajar.
• The luggage barrier must be in place.
• The pump motor temperature must be within the operating range.

After the last cycle of power folding top operation, allow the hydraulic system a minimum of 4 minutes to bleed down before attempting manual operation of the top.
Your best bet take and have it checked for DTC'S - diagnostic trouble codes .
DTC B3666 Rear Tonneau Position Error
DTC B3667 Tonneau Release Circuit
DTC B1011
DTC B1291
DTC B1420
DTC B3602
DTC B3666
DTC B3667
DTC B3670
DTC B3971

Jan 23, 2017 | 2007 Chevrolet Corvette Convertible

1 Answer

On a 207 G6 GT Pontiac retractable hardtop where is the sensor that gives the message top not secure. Top goes up and down seem secure will not allow the trunk to open with the key or door button


The retractable hard top is controlled by the folding top control (FTC) module.
Power Folding Top System Components
The power folding top system consists of the following components:
?€¢
The folding top control (FTC) module


?€¢
Hydraulic pump assembly; valve 1, valve 2 and motor


?€¢
The hydraulic lines and the cylinders


?€¢
GMLAN communication to the Body Control Module (BCM)


?€¢
Open/Close request circuit to the driver and passenger window motors


?€¢
Power and Grounds


-
Folding Top Main Power Fuse 30A


-
Folding Top Logic Power Fuse 20A


-
Ground G301 for the FTC module and G305


?€¢
Folding Top Open/Close Switch (S15 and S16)


?€¢
Rear Compartment Limit Switches


-
Rear Compartment Lid Release Switch (S3 and S4)


-
Rear Compartment Lid Release Switch-Front Hinge-Left (S11 and S12)


-
Rear Compartment Lid Release Switch-Front Hinge-Right (S9 and S10)


-
Folding Top Front Location Pin Guide-Left (S17 and S18)


-
Rear Compartment Lid Release Switch-Left (S19A)


-
Rear Compartment Lid Release Switch-Right (S19B)


-
Rear Compartment Partition Position Switch (S20)


-
Folding Top Front Location Pin Position Switch (S13)


-
Folding Top Front Latch Actuator Position Switch (S14)


?€¢
Hall Effect Sensors


-
Folding Top Header Latch Cylinder Sensor (S1)


-
Rear Compartment Cylinder Extended Sensor (S2)


Your best bet is have the system checked for DTC'S - diagnostic trouble codes ! If it showed a message top not secured there is a DTC stored in the control module ! there are 24 possible DTC'S

May 29, 2015 | 2007 Pontiac G6 GT

1 Answer

I have a 2003 chevrolet tahoe how do I fold The seat down


The second row is folded by first pulling up the rear of the seat cushion and folding up 'til it's behind the back of the front seat. Then the back of the seat folds down where the seat cushion was.

The third row seats have several levers that are numbered in the sequence they are to be operated. First fold the seat back down on to the cushion and then flip the whole seat up 'til it's vertical and latched.

This is described in the Owner's manual if you can find one.

Mar 15, 2015 | 2003 Chevrolet Tahoe

1 Answer

How do seats fold down?


There might be a short strap in the center of each section where the back and the seat come together. Pull that strap to release and fold the seat aginst the front seat. Then you should seelatches to release the backs and fold them down. Hope this helps

Sep 25, 2014 | 2002 GMC Yukon Denali

1 Answer

How do you get the top down on 90 convertible


To lower the top. 1) open the drivers door and under the fiberglass cover there is a lever that will release the two pins that hold the rear cover down. 2) lift up the rear window part of top and reach under again to press button that will release fiberglass cover. ( there is also a button on the passenger door which is visible with the door open.) this is a electric relay switch which will produce a clicking sound and top will come up. 3) release the two levers on the front of the cover by pulling toward you. 4) fold cover in compartment and fold levers back to folded position.

Jun 20, 2009 | 1990 Chevrolet Corvette

1 Answer

HOE TO FOLD DOWN REAR SEATS


1 lift the front of the lower part of the seats, then fold the lower part front
2 remove the headrest and fold upper part front

Apr 19, 2009 | 2004 Porsche Cayenne

2 Answers

Front seat won't fold down the release lever is not working


the mechanism is burried deep inside the acctual seat. there will be an access fold which consists of a piece of plastic which is folded at the botom of the back of the seat which should untuck so to speak and allow you to access the back enough to see the offending clasp

Feb 25, 2009 | 2007 Fiat X1/9

1 Answer

Front Seat Broke/Fold Down Arm rest broke


i have to 60/40 seat with a fold down console,

Sep 18, 2008 | 1991 Ford Ranger Supercab

1 Answer

How to fold down back seat


There should be a loop between the seat and backrest, pull that and the seat will pull toward the front seats. After that, pull the lever located at the outside of the backrest. This lever is on the outside of the seat by the door-side of the seat. Pull that up and allow the backrest will fold down and the headrest will pivot back and your seat is folded down.

Jun 28, 2008 | 2004 GMC Envoy

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...