Question about 2002 Dodge Ram 3500 Truck

1 Answer

2004 dodge ram 3500 4x4 do i have to take the large nut off the s

Rotor removal

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 111 Answers

Should be a slide off composite rotor remove caliper and caliper holding bracket bolts on back side

Posted on Sep 13, 2009

  • ALAN BROWN Sep 13, 2009

    should be a slide off composite rotor remove caliper and caliper holding bracket bolts on back side

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I get rotors off a 95 Dodge ram 2500 4X4


First off, don't expect them to just fall off after removing the large nut in the center of the hub. I tried that. Granted, the nut does need to come off, but, after removing the caliper, there's four more bolts that come in from the backside that also need to be removed. This then allows you to remove the front spindle, hub, and rotor as an assembly. Watch your toes! Also note how the dust shield is sandwiched in amongst all of this. Once this assembly is off, the wheel studs can be driven out with a hydraulic press (no small feat), and the rotor falls away from the hub

Feb 13, 2012 | 1995 Dodge Ram 2500

1 Answer

2006 dodge ram 3500 dually 4x4 front rotor....can I remove rotor without removing axle nut?


I beleve all heavy duty trucks would have a axle nut to adjust/hold it in.

Aug 24, 2011 | Dodge Ram 3500 Cars & Trucks

1 Answer

How do i remove the hub assembly from the front wheel of my 2001 dodge ram RWD?


  • Jack up your Dodge Ram. Block the wheels to keep it from rolling as you work. Get started by removing the first tire and wheel assembly. Remove the hub extension and the brake caliper as well as the caliper adapter.
  • Remove the grease cap, cotter pin, nut lock, nut, washer and outer wheel bearing. Now, pull the old rotor off of the spindle. Clean the area with a damp cloth to remove any debris. Pack the wheel bearings with grease.
  • Install the new rotor and hub onto the spindle. Replace the outer wheel bearing, washer, and then the retaining nut. Torque the nut to 30 to 40 ft. lbs. while rotating the hub and rotor. Then tighten the nut and install the nut lock and a new cotter pin.
  • Clean the grease cap and then coat it with new wheel bearing grease and replace the cap. Put the caliper adapter back into place and then tighten the two mounting bolts with a torque wrench. Install the wheel and tire assembly.
  • Repeat this process for each additional rotor and then lower the vehicle. Tighten the lug nuts and test drive your Dodge Ram to make sure that the installation was successful.


  • If I've helped, please vote!

    Dec 10, 2010 | 2001 Dodge Ram 1500 Truck 2WD

    1 Answer

    What is the procedure for replacing ball joints in 2004 doddge ram 3500 4wd quad cab dually?


    first put truck on jack stands and remove tires then you will need heavy duty impact to remove axle nuts then remove the four bolts that hold wheel bearing in you access them from the back side of rotor on the spindle then remove the brake caliper and bracket you will need a puller to put on the rotor or studs and push against the axle shaft dont forget to unplug speed sensor if equipped after you remove rotor and bearing assembly the axle will slide out allowing you to get to lower ball joint nut remove both nuts and steering rod use ball joint fork and remove spindle use press and remove and reinstall new joints put back in reverse order be very careful with left side axle make sure its clean and hold it up in the center as not to damage seal when going back in because it is bear to replace i hope this helps you allow yourself a good day for this job

    Nov 03, 2010 | 2004 Dodge Ram 3500 Truck

    1 Answer

    How to change rear rotors on a 2004 dodge ram 1500


    Remove the tire, and the rotor pulls straight off like the tire. Unless you have disk brakes. In that case, feel the back of the caliper "its whats holding the rotor on" you will feel 2 bolts. Remove them. The caliper slides off sideways. Then just slip the rotor off. The caliper will just dangle there until your ready for it. You do not need to remove the brake lines.

    Jun 10, 2010 | 2004 Dodge Ram 1500

    1 Answer

    Removing the rear rotors


    REMOVAL - REAR ROTORS
    (1) Raise and support the vehicle
    (2) Remove the tire and wheel assembly.
    (3) Remove the disc brake caliper, (Refer to 5 -
    BRAKES/HYDRAULIC/MECHANICAL/DISC
    BRAKE CALIPERS - REMOVAL).
    (4) Remove the caliper adapter bolts (Fig.
    61).(Refer to 5 - BRAKES/HYDRAULIC/MECHANICAL/
    DISC BRAKE CALIPER ADAPTER -
    REMOVAL)
    (5) Remove the retaining clips and rotor assembly

    (Fig. 61).
    c0d28fd.jpg

    You can get a factory service manual from Promanuals.net here is a link to the 2004 Dodge Ram Service Manual it was only 20 bucks and very informative.

    Sep 29, 2009 | 2004 Dodge Ram 2500

    1 Answer

    I think my front Drivers side wheel bearing is going out on my 2004 dodge ram 1500 4x4. It is an ABS system. What should I do to replace this? I wouldnt mind doing it myself if its the cheaper route.


    Remove the wheel, the brake caliper with the mounting bracket and pads all together, the brake rotor, and the axle nut. Make sure the axle is free inside the hub splines by pushing it in a bit. I believe this truck has 3 bolts for the hub/bearing assy. They remove from the inboard side of the knuckle, then the hub/bearing assy comes out. It may be corroded in the knuckle, so some force may be required to get it out. To reassemble, reverse the steps, being careful to torque the axle nut to the proper spec. Also pump the brake pedal before you road test to verify the noise is gone.

    Jun 27, 2009 | 2004 Dodge Ram 1500

    1 Answer

    2002 Dodge Ram 1500 4 w drive rear rotors


    Can't tell you exactly how because i don't know what axle you have, but usually just take the main nut in the center off will bring it right out. Remove the wheel, and the brake calliper first and see if it comes off then remove the center nut.

    Mar 20, 2009 | 2001 Dodge Ram 1500 Truck 2WD

    2 Answers

    How to remove rotors on 97 dodge 2500 4x4


    sounds like the rotor is stuck on the hub. Try beating it with a hammer you dont have to take the 4 bolts off they remove the wheel bearing. Axle doesn't have to be touched as well. After you remove the caliper and bracket the rotor should fall off.

    Mar 09, 2009 | 1999 Dodge Ram

    1 Answer

    Rear hub removal on a dodge 2004 ram 3500


    REMOVE THE RUBBER PLUG IN BACKING PLATE AND ADJUST E BRAKE SHOES DOWN TO REMOVE ROTOR

    Feb 15, 2009 | 2004 Dodge Ram 3500 Truck

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    112 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Dodge Experts

    yadayada
    yadayada

    Level 3 Expert

    75817 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8180 Answers

    Are you a Dodge Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...