Question about 1992 GMC Jimmy

2 Answers

Need instructions for removal and installation of front u-joint on 1989 gmc jimmy

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • GMC Master
  • 3,433 Answers

If you have never done it before, It would be best to just remove the shaft and watch how the joint is removed and installed, by a mechanic. You can avoid damaging the new u=joint or bending the yoke. Then your problems begin. Let someone show you the how on the first one and it will be a cakewalk thereafter. Good luck.and be safe. Make sure the driveshaft has no load or pressure on it before loosening any bolts.._Ned_

Posted on Sep 17, 2009

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 811 Answers

Buy manual, removal:  raise vehicle and place on jack stands remove skid-plate, mark relationship of driveshaft to the front diff flange and the transfer case flange, remove the bolts and straps from diff flange and trans case flange, push the rear half of the driveshaft forward far enough to separate it from the transfer case flange, then lower it and separate it at the diff flange. installation: attach the front end of the driveshaft to the front diff flange and install the straps and bolts finger tight, extend or compress the driveshaft as necessary , attach the rear end to the transfer case flange, install the straps and bolts and tighten all bolts to 59 ft #'s , install skid plates, and lower vehicle 

Posted on Sep 13, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1989 suburban front bumper


Sara, 1989 GMC Suburban front bumper removal. Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
How To Install Replace Bent Rusted Front Bumper 1989 99 Chevy GMC Pickup...
Grille Replacement 88 98 Chevy trucks
1989 Chevrolet R1500 Suburban Parts NationalGMParts com

Jul 10, 2016 | 1989 GMC Suburban

1 Answer

Repacing drain petcock 1989 gmc jimmy s15


They Screw Out Like a Bolt And In The Same Way

May 24, 2015 | 1989 GMC S-15 Jimmy

1 Answer

Front axle seal leaking


That means that you need to replace the seal, might as well do the bearing and the cv joint too.

Sep 27, 2013 | 1998 GMC Jimmy

1 Answer

I need step by step instructions on replacing front lower ball joints on a 1996 GMC JIMMY4X4.


first you will need to buy a ball joint press. first jackup and place jack stand under oneside of jimmy1).remove the tire.2)remove caliper and pads and rotor.3) remove cotter pin out of nut for tie rod end then remove nut. 4) loosen tie rod end from knuckle donot split greese boot or hit top of stud as this will damage it.5)remove axle nut and push back axle may be frozen in hub.6) remove both cotter pin and nuts on ball joints then spin on bottom nut a couple threads as no thave knuckle fall to the ground.7)loosen ball joint from knuckle and remove knuckle.8) remove ball joints with press or by rmoving rivits install in reverse procedure

Sep 06, 2009 | GMC Jimmy Cars & Trucks

1 Answer

How do i change the ignition tumbler on my 1989 s15 jimmy


you have to remove the steering wheel, turn signal/emergency flasher switch assembly and a couple other pieces below that. If you have tilt steering the little clip is easy to remove but hell to get back in so if you are not the patient type take a break and try installing it again a little later.The ignition switch should be held in by a bolt. Once the bolt is removed the ingition switch slides out and the new one can be installed.

Aug 15, 2009 | 1989 GMC S-15 Jimmy

1 Answer

Replacing lower ball joint-GMC JImmy


is this a 4 wd drive unit or 2wd unit? are you mechanically inclined and have basic common tools including a jack and jackstands? if you live close to pep-boys auto center then you can take it there you will spend about 200-300 to do the job, just ask them for a qoute first and that hopefully is still free. they have a special coupon on there wbsite right now that will save you some money, plus if you are over 55 or student in school you can also save money there. i was a service manager there for a while... let me know what you want to do they are not super hard to do but can give you a headache if you dont have a grinder or chisel. i can walk you through it though if you still wish, im all for the do it yourselfer.

Mar 03, 2009 | 2001 GMC Jimmy

1 Answer

89 S15 4.3L Need instructions to remove and install pwr steering


i know what bolt your talking about,you canreach it thru the wheel well with an extention!!!
but if your just removing the pump,some of the pullys have three holes in them too get too the pump bolts if not then you need a power steering pump pully remover auto zone loans them out!!!!

Feb 28, 2009 | 1989 GMC S-15 Jimmy

1 Answer

1997 GMC Jimmy Crank Angle Sensor


it's at the front of the engine and below the and left of the front of the crank shaft.
dis-connect negative attery cable
dis-connect the electical connector to the sensor
un-bolt it and pull it out
reversr for installation

Oct 03, 2008 | 1997 GMC Jimmy

Not finding what you are looking for?
1992 GMC Jimmy Logo

Related Topics:

231 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...