Question about 2008 GMC Yukon Xl 4WD

1 Answer

Why would the track stabiltiy light come on when I start the vehicle and it shakes when i put it into gear, either drive or reverse?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 4,044 Answers

This is controlled by a solenoid in the transmission. You need to have the transmission checked.

Posted on Sep 12, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hilux diesel 08 auto turn lights on reverse light comes on and starts rEving harder like its dropping gears and engine light on while I'm driving


Bigjoe...You need to check for the fault code associated with your engine light. Your vehicle has a computer that stores these codes to assist in tracking down problems.

Some retail auto parts stores will plug in their OBDII hand held code reader for free. This will provide you with a starting point to help determine what is wrong with your 2008 Hilux.

Jun 30, 2016 | Toyota Hilux Cars & Trucks

2 Answers

I worm the car up put it in reverse it shakes into gear put the car in drive give it gas starts shaking and jerking into first gear than it does the same thing into 2nd gear and on hills


details here are very scarce like, year make model, manual or auto, work done ,how long has this been happening
when you give this information then you may get an answer

Apr 24, 2015 | Cars & Trucks

1 Answer

Battery fully charged, engine won't start or even turn over, gear locked in park, brake pedal is depressed.


This may help: http://www.toyotanation.com/forum/274-2nd-generation-2004-2010/199861-04-sienna-transmission-lock.html
There are multiple issues here.Won't crank? Go direct to starter.

Possible recall:http://www.toyoheadquarters.com/threads/2004-2005-2007-2009-toyota-sienna-shift-lock-solenoid-recall-d0r.206/

Nov 10, 2014 | 2004 Toyota Sienna

1 Answer

Toyota sienna 2001 won't go in reverse but it goes forward


Does it crunch? If you lift the clutch and then press it down whilst trying to get it into reverse as this lets the cogs move allowing you to slip the drive into the gears this may allow you to get it into reverse. So here's the steps:
1 start the the engine
2 drive the car for about 10 kms
3 try and get the vehicle into reverse
4 lift the clutch whilst holding the stick in the gate ( you should feel the cogs turning and shaking the stick)
5 then push the clutch down again
6 if it still won't go repeat step 4/5
if it still won't work then try and get it into reverse whilst stationary and then start the engine it will jolt but can free up the gears!

hope this helps :)

May 15, 2014 | Cars & Trucks

1 Answer

My 2000 Ford Taurus starts shaking only when I apply the breaks in reverse?


check you motor and transmission mounts. if one of them are wore out it will cause the car to do this. i just fixed a mazda with the exact some problem yesterday, but the situation was in reverse. runs like a champ now

Aug 18, 2012 | Ford Taurus Cars & Trucks

1 Answer

I have a F250 lariat with a 460 - truck stalls when I put it in gear - even after it runs for 20 min. Sometimes it will stall while I'm driving. I had carborator replaced last year. Hope you can help.


Some possible causes could be:

Vacuum leaks cause an engine to run lean witch can cause the vehicle to stall when put into gear.

Improper base idle adjustment can cause the vehicle to stall when shifted into drive or reverse

A malfunctioning or damaged carburetor can cause the vehicle to stall when shifted into drive or reverse

Improper ignition timing can cause the vehicle to stall when shifted into drive or reverse.

A malfunctioning or damaged transmission or torque converter can cause the vehicle to stall when shifted into drive or reverse

Oct 31, 2010 | 1987 Ford F 250

1 Answer

When put into drive the car shakes and stalls. It


I have a 1989 5-series BMW which sometimes stalls after changing from reverse to drive. It also sometimes shakes when first driving in reverse before changing to drive.

Jan 30, 2010 | 1992 Mazda Protege

1 Answer

Saturn Ion shakes when started.


I would take the vehicle in to a mechanic.
There could be damage internally with the engine.
or the transmission.

Apr 04, 2009 | 2006 Saturn ION

1 Answer

The engine in my 96 saturn wagon shakes when it is put into gear, reverse or drive.


remove the belt and spin all of the pulleys by hand to make sure they all spin freely. the knocking noise is probebly a pulley locked up.

Nov 08, 2008 | 1996 Saturn SW

1 Answer

Car shaking


something wasnt put back together properly or the mounts are no longer servicable

Aug 16, 2008 | 1992 Nissan Maxima

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

56 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...