Question about 1992 Buick Park Avenue

1 Answer

I need to replace a/c clutch, its metal on metal and chattering.also the crank sensor(i believe)is moving or vibrating; with motor off can wiggle with finger.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 811 Answers

Tighten crank sensor, go online to buy clutch rebuild kit

Posted on Sep 12, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Trying to find out where the crankshaft sensor is located on Mazda Tribute 2002? Need to change it


2004 Mazda tribute 2.0l manual transmission cranks position sensor tip worn / rubbing. p0351, p0352, p0500, p0320 codes. I have a 2004 Mazda tribute with 2.0l 4 cylinder. 140,000 miles. First problem was it would not start but I could hear the fuel pump run and the engine cranked over. I checked for spark and all four plugs had no spark. p0351, p0352, p0500, and p0320 codes displayed.
I have 12 volts at coil. I decided to remove and inspect crank sensor on the transmission side of the engine ( on engine below thermostat housing bolted to engine block) once i removed it i noticed the tip of the sensor was broken, yes, broken. so I knew i found the problem.
I put a new crank sensor in and the car started but ran for 1 hour idling as if a cylinder was not firing. Then it would not start ever again. I removed my brand new replacement sensor to find the tip was rubbed off enough to see the inside metal. i think it could be a possible warped flywheel but I am having trouble finding diagrams of the excitation part of how the crank position sensor works.
I believe the flywheel has holes that excite the sensor. The tribute does move and clutch works for the hour I had it running, so the manual Trans does work as well as the clutch.
https://electronicshelponline.blogspot.com/

Jul 16, 2016 | 2002 Mazda Tribute

1 Answer

Will a bad fan clutch cause vibration


Yes it will. With the motor of wiggle the fan. If it wiggles then yes,replace it

Mar 01, 2015 | 2002 Chevrolet TrailBlazer

1 Answer

2002 Mazda 626 front end vibration when in gear but not moving


I think this was posted once before but it is either the torque converter or the harmonic balancer

Feb 12, 2013 | 2002 Mazda 626

1 Answer

2002 mazda 626 front end virbation when in gear but not moving


check the dust covers on the exhaust system

Feb 12, 2013 | 2002 Mazda 626

1 Answer

Clutch judder & vibrates, toyota corolla.


The problem is the clutch and the engine flywheel are heat damaged, this is called clutch "chatter" You must have the entire clutch replaced and the flywheel machined smooth again. The damage is caused by excessive slipping of the clutch on take off. Release the clutch asap when you start off, do not slip it for long periods this turns it nearly read hot.

Oct 11, 2012 | 2004 Toyota Corolla 1.4

1 Answer

Po306 code on a 1996 Chevy Lumina also ge a metallic squeak from the drive belt end of the motor. with the belt off as well


the bottom crank pulley is either lose! the keyway sheared and vibrateing against the crank sensor or the bolt in the crank pulley has backed off or fell out

Jan 21, 2010 | 1996 Chevrolet Lumina Mini

2 Answers

Engine shuts down, will crank but not start.


You need a crank shaft position sensor, located in the bell housing of the transmission. This is an extremely common problem on these.

Apr 13, 2009 | 1998 Jeep Grand Cherokee

1 Answer

1999 Mercury Mountaineer- Chattering Reverse to Drive Automatic


sounds like the u-joints in the front axle are bad or were installed incorrectly they only come into play when the wheel is turned. These are the axle ujoints not the driveshaft ujoints

Apr 08, 2009 | 1999 Mercury Mountaineer

1 Answer

AC Compressor clutch problem


Hi

This could be any number of things, low system pressure, chattering relay, faulty cycling switch, failed compressor, poor cooling, the list goes on.

I'm afraid this is a job for the professionals!

Very best regards

Geordie

Jun 11, 2008 | 2005 Ford Taurus

Not finding what you are looking for?
1992 Buick Park Avenue Logo

Related Topics:

64 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...