Question about 1989 Chevrolet K1500

1 Answer

Need to take rear seal out what do i do

Need to take rear seal out of a 700r what do i do need step by step

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 811 Answers

Remove drive line, remove yoke, take screwdriver and pry seal out careful not to damage housing, replace seal, lubricate and reassemble

Posted on Sep 12, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I replaced the seal in the rear ended but it is still leaking what's next


Leaking seal could mean the yoke surface that the seal rubs on is rough, or that yoke is moving because of diff wear or misadjustment.

Sep 06, 2016 | 2009 Dodge Dakota Extended

1 Answer

700r transmission


Check for a bad CV shaft

Mar 10, 2014 | Cars & Trucks

1 Answer

Remove transmission 2002 toyota corolla 1.8 l 4 cyl 5 speed


go to autozone dot com. Register for free, login, choose vehicle year make model, then view free online repair manual

Jun 10, 2012 | 2002 Toyota Corolla

1 Answer

I have a 2006 Pontiac Grand Prix, it is supercharged 3800. I have about 115,000 miles on it and I change the oil every 3,000 miles, check fluids, regular preventative maintenance, etc. I noticed a small...


If it's oil, it's coming from the rear main seal.. I would go with this idea.

The seal doesn't cost much but the labor to get to it does.

To give you an idea what is involved the procedure is illustrated below from the service manual:

Removal & Installation 3.8L Engine To Remove:
  1. Drain the engine coolant.
  2. Drain the engine oil.
  3. Remove the oil pan.
  4. Remove the engine flywheel.
  5. Remove the rear oil seal housing and gasket. Rear seal removal 3.8L gm-03-38-1175.gif

  6. Remove the rear main seal by placing the housing face down on 2 blocks of wood. Using a drift tool and hammer tap the seal out of the housing.
To Install:
NOTE: Do not lubricate the rear main oil seal or the installation tool. Do not touch the sealing lip of the rear main seal once the protective sleeve is removed.
NOTE: Use a clean lint free cloth to clean the crankshaft sealing surface. Remove sharp edges or burrs that could damage the rear main oil seal. Remove burrs or sharp edges with a crocus cloth.
  1. Carefully remove the rear oil seal from the protective sleeve.
  2. Install the oil seal onto the seal driver EN-47623 or equivalent by placing the seal at an angle and twisting until it is fully seated.
  3. Install the seal into the housing using the seal driver EN-47623 or equivalent and driver handle J-8092 or equivalent. Apply downward force until the seal is seated. NOTE: Ensure that the housing gasket is installed correctly and that the oil passages are not blocked.
  4. Using a new gasket Install the rear oil seal housing on the engine being careful not damage the rear main seal. NOTE: The plastic inserts are used in production and are not needed for assembly.
  5. Hand tighten the bolts. Rear seal housing alignment 3.8L gm-03-38-1176.gif

  6. Place a straight edge on the crankshaft rear oil seal housing flange and the engine block oil pan flange. Using a feeler gauge check that there is no more than .0004 in (0.10 mm) step on each side. Rotate the housing to make the steps equal on both sides.
  7. Tighten the housing bolts 11 ft-lb (15 Nm) plus an additional 50 degrees.
  8. Ensure that the housing did not move out of specification. Repeat step 6 if the oil seal housing is not within the specified range. Replace the rear oil seal housing if the specified measurement can not be reached.
  9. Install the flywheel.
  10. Install the oil pan.
  11. Fill the engine oil and the cooling system.
  12. Check for leaks
5.3L Engine To Remove:
  1. Remove the flywheel from the crankshaft.
  2. Remove and discard the crankshaft rear oil seal from the rear cover.
To Install:
  1. Use clean engine oil to lubricate the outside diameter of the crankshaft rear oil seal and rear cover oil seal bore.
  2. Install the tapered cone and bolts of a J 41479 or equivalent crankshaft rear oil seal installer onto the crankshaft.
  3. Place the crankshaft rear oil seal onto the tapered cone.
  4. Install the threaded rod of the J 41479 crankshaft rear oil seal installer into the tapered cone. Rear main seal installer 5.3L gm-03-53-3872.gif

  5. Install the crankshaft rear oil seal by turning the handle of the J 41479 clockwise.
  6. Remove the J 41479 crankshaft rear oil seal installer from the crankshaft.
  7. Install the flywheel onto the crankshaft.
prev.gif next.gif--- I'm not sure what the exact cost would be as the hours were not listed for this procedure on my online resource.

Sep 02, 2010 | 2006 Pontiac Grand Prix

1 Answer

Exchange tail shafts on chevy 700r transmission .need to swap out tail shafts so i will have the same distance for drive shaft


In order to change the length of the shaft coming out of the rear of the transmission you would have to disassemble the transmission and install the correct length output shaft.

Oct 14, 2009 | Chevrolet Caprice Classic Cars & Trucks

1 Answer

Rear main seal needs to be replaced,leaking oil from where trans. joins to motor need a step by step manual pics would be very helpful.


if its one piece round seal must pull trans if 2 piece drop pan good luck how many miles may have bad blow by check pcv valve

Aug 29, 2009 | 1993 GMC Safari

1 Answer

Rear axel seals are leaking


bowhunter 72,
you can purchase a haynes repair manuel at your local parts store for your 2004 Ford F-150. these books have step by step information with some illustrations that will be benifical in completing your desired repairs of replacing your rear axle seals..hope this helps you. chris

May 13, 2009 | 2004 Ford F150

1 Answer

How to Change Rear Axle Seal?


When you take the rear drum off, look where the axle goes in and if there are 4 bolts around it, you don't have to go into the diff. If there are no bolts holding the axle in, then get a repair manual to guide you through the steps. The seal on an axle that is bolted in place will have a collar that needs to be pressed off and a new one back on. These seals can be bought at a local partsd house.

Nov 09, 2008 | 1989 Jeep Wrangler

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

65 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8202 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...