Question about 1993 Lexus Ls 400

1 Answer

Disconneted battery and installed a water pump car wont start

Disconneted battery and installed a water pump bracket now car wont start like getting no fire. what to do is there a theft protection for having the battery disconnected

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Lexus Master
  • 22,095 Answers

Yes its possible it has a factory immobiliser ,from around 94 but as its a take off of a merc then yes its highly possible it has alarm ....sorry if it has dealer only

Posted on Sep 12, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

HOW TO REPLACE WATER PUMP 2001 explorer sport 4.0


Disconnect the battery, locate the idler bracket that adjust the tension on the belt. Loosen the bracket and unhook the belt off of the Idler bracket(no need to remove belt unless in the way) Remove water pump when car is cooled down. Loosen bolts that hold the water pump on and remove pump. Put new one on and reverse process. Replace your antifreeze/ water. Start car for thirty seconds. Stop car, look for leaks and top off antifreeze. Done deal.

Feb 08, 2015 | 2001 Ford Explorer Sport

1 Answer

I recently changed the alternador belt on a 2001 chevy metro lsi, afterwards whenever i start the car , there is this rattling noise and when i opened the hood to check , to the left of the alternador...


Water Pump REMOVAL & INSTALLATION Metro
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Drain the cooling system.
  3. Remove or disconnect the following:
    • Negative battery cable
    • Air cleaner
    • A/C compressor suction pipe bracket, if equipped
    • Loosen the water pump pulley bolts. Do not remove them at this time
    • Right side lower splash shield
    • A/C compressor drive belt
    • Lower alternator cover plate
    • Water pump/alternator drive belt
    • Crankshaft pulley
    • Water pump pulley
    • Timing belt
    • Dipstick tube
    • Upper alternator bracket from the water pump
    • Water pump and discard the gasket
    To install: Fig. 1: To ensure a tight seal, be sure gasket surfaces are properly prepared - Metro 7922z704.gif

  4. Clean the gasket mating surfaces thoroughly.
  5. Install or connect the following:
    • Water pump with new gasket. Torque the bolts to 115 inch lbs. (13 Nm).
    • New rubber seals
    • Upper alternator adjusting bracket
    • Oil dipstick tube
    • Timing belt
    • Water pump and crankshaft pulleys. Leave the water pump pulley bolts hand-tight
    • Alternator drive belt
    • Lower alternator cover plate. Torque the bolts to 89 inch lbs. (10 Nm).
    • A/C compressor drive belt, if equipped
    • Right side lower splash shield.
    • Torque the water pump pulley bolts to 18 ft. lbs. (24 Nm).
  6. Adjust the water pump drive belt tension and torque the alternator adjustment bolt to 17 ft. lbs. (23 Nm).
  7. Install or connect the following:
    • A/C compressor suction pipe bracket, if equipped
    • Air cleaner
    • Negative battery cable
  8. Refill the cooling system.
  9. Start the engine and check for leaks, repair if necessary.
Prizm 1.6L ENGINE
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Drain the engine coolant.
  3. Remove or disconnect the following:
    • Negative battery cable and properly support the engine
    • Right side engine mount and support
    • Upper and middle timing belt covers
  4. If equipped with power steering remove the following components:
    • Front transmission mount
    • Radiator fan motor
    • Coolant reservoir
    • Upper radiator hose
  5. Remove or disconnect the following:
    • Crankshaft Position (CKP) sensor electrical connector from the dipstick tube
    • Dipstick tube
    • Engine Coolant Temperature (ECT) sending unit
    • Coolant inlet pipe
    • Water pump and discard the O-ring Fig. 2: Remove the coolant inlet pipe from the block, then the pump - Prizm 7922z705.gif
    To install:
  6. Install or connect the following:
    • New O-ring and Water pump. Torque the bolts to 10 ft. lbs. (14 Nm).
    • Coolant hose to the pump
    • Coolant inlet pipe. Torque the fastener to 11 ft. lbs. (15 Nm).
    • Dipstick tube. Torque the bolt to 89 inch lbs. (10 Nm).
    • ECT sending unit to the dipstick tube
    • Engine wire harness. Torque the bolt to 89 inch lbs. (10 Nm).
    • Radiator fan. Torque the bolts to 52 inch lbs. (6 Nm).
    • Upper radiator hose
    • Coolant reservoir
    • Front transmission mount. Torque the bolt to 47 ft. lbs. (64 Nm).
    • Upper and middle timing belt covers. Torque the bolts to 62 inch lbs. (7 Nm).
    • Right side transmission mount and insulator. Torque the bolt to 47 ft. lbs. (64 Nm).
    • Negative battery cable
  7. Fill the cooling system.
  8. Start the vehicle and check for leaks, repair if necessary.
1.8L ENGINE
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Drain the engine coolant.
  3. Remove or disconnect the following:
    • Negative battery cable
    • Drive belt
    • Right side lower splash shield
    • Water pump and discard the O-ring
    To install:
  4. Install or connect the following:
    • New O-ring and water pump. Torque the bolts to 8 ft. lbs. (11 Nm).
    • Right side lower splash shield
    • Drive belt
    • Negative battery cable
  5. Fill the cooling system.
  6. Start the vehicle and check for leaks, repair if necessary.
prev.gif next.gif

Jan 02, 2011 | Chevrolet Metro Cars & Trucks

1 Answer

My antifreeze keep leaking out , it started a few days ago.the car runs good i have had it two years without any problems can you tell me what might be going on , it the only car i have.


The water pump and related area may be leaking antifreeze. Check near the belt pulley for the water pump. There may be other issues that require the gasket further in the engine changed which is related to engine oil. My family had a 1998 Ford Taurus that had this problem and it cost a few hundred to have it fixed.

One may also look for a leak at the radiator (or hoses )which is further forward.
---
.
Water Pump Removal & Installation 3.0L (2V) To Remove:
  1. Drain the engine cooling system.
  2. Loosen the water pump pulley.
  3. Remove the bolt and the nut and position the roll restrictor bracket out of the way.
  4. Remove the accessory drive belt.
  5. Remove the generator.
  6. Remove the bolt and the accessory drive belt tensioner.
  7. Remove the nut, the bolt and the support bracket.
  8. Remove the bolts and the water pump pulley.
  9. Disconnect the water pump inlet hose and the crankshaft position sensor electrical connector.
  10. Remove the bolts and the water pump, and clean the sealing surfaces
To Install:
  1. Install the water pump. Tighten bolts in the sequence shown:
    • Tighten numbers 1-7 to 18 ft.-lbs. (25 Nm)
    • Tighten numbers 8-12 to 89 in.-lbs. (10 Nm)
    Water pump bolt torque sequence (3.0L (2V) engine) ford-03-30-409.gif

  2. Connect the crankshaft position sensor electrical connector and the water pump inlet hose
  3. Install the support bracket.
  4. Install the accessory drive shaft tensioner.
  5. Install the generator.
  6. Install the roll restrictor bracket, bolt and the nut.
  7. Install the water pump pulley.
  8. Install the accessory drive belt.
  9. Connect the battery ground cable.
  10. Fill the engine cooling system.
3.0L (4V) To Remove:
  1. Before servicing the vehicle refer to the precautions in the beginning of this section.
  2. Drain the cooling system.
  3. Raise and support the vehicle.
  4. Remove the right front splash shield.
  5. Disconnect the hoses from the water pump.
  6. Lower the vehicle.
  7. Remove the accessory drive belt.
  8. Disconnect the upper hose from the water pump.
  9. Remove the A/C compressor support brace.
  10. Remove the four mounting nuts and the water pump.
To Install:
  1. Position the water pump and install the mounting nuts. Tighten the nuts to 18 ft.-lbs. (25 Nm).
  2. Install the A/C compressor support brace.
  3. Connect the upper hose to the water pump.
  4. Install the drive belt.
  5. Raise and support the vehicle.
  6. Connect the hoses to the water pump.
  7. Install the splash shield.
  8. Fill the engine cooling system.
prev.gif next.gif

Oct 07, 2010 | 2000 Ford Taurus

1 Answer

Step by step to replace water pump on a 1995 chevrolet camro.


Water Pump - REMOVAL & INSTALLATION
CAUTION When draining the coolant, keep in mind that cats and dogs are attracted by ethylene glycol antifreeze, and are quite likely to drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantity. Always drain the coolant into a sealable container. Coolant should be reused unless it is contaminated or several years old.
3.4L ENGINE
(see Figures 1 and 2)
  1. Disconnect the negative battery cable.
  2. Drain the cooling system into a suitable container.
  3. Remove the air intake duct.
  4. Remove the top coil of the ignition coil pack.
  5. Loosen the tensioner pulley bolt/screw.
  6. Disconnect the heater hose from the water pump.
  7. Loosen the water pump pulley bolts/screws.
  8. Unfasten the power steering bracket bolts/screws.
  9. Remove the serpentine drive belt.
  10. Remove the water pump pulley.
  11. Remove the power steering pump bracket and swing the bracket and pump aside. Do NOT disconnect the power steering lines from the pump.
  12. Unfasten the water pump and engine front cover bolts/screws, then remove the water pump assembly from the vehicle.
  13. Remove and discard the gasket and thoroughly clean the gasket mating surfaces.
9940b19.jpg

Fig. 1: Exploded view of the water pump mounting - 3.4L engine

To install:

  1. Position a new water pump gasket, then install the pump. Secure using all of the water pump retaining bolts/screws, except the bottom three, and tighten to 33 ft. lbs. (45 Nm).
  2. Install the engine front cover bolts/screws and tighten to 16 ft. lbs. (21 Nm) for 1993-94 vehicles, or to 97 inch lbs. (11 Nm) for 1995 vehicles.
371be42.jpg

Fig. 2: Water pump retaining bolt tightening sequence
  1. Install the three bottom water pump retaining screws and tighten to 89 inch lbs. (10 Nm).
  2. Place the power steering pump into position and install the pump bracket.
  3. Install the water pump pulley.
  4. Install the serpentine drive belt.
  5. Install the power steering pump bracket retaining bolts and tighten to 30 ft. lbs. (40 Nm).
  6. Connect the heater hose to the water pump.
  7. Install the top coil to the ignition coil pack.
  8. Attach the electrical connector to the alternator.
  9. Install the air inlet duct and air cleaner assembly.
  10. Connect the negative battery cable.
  11. Fill the cooling system. Start the engine and check for leaks.


3.8L Engine
  1. Disconnect the negative battery cable.
  2. Drain the cooling system into a suitable container.
  3. Remove the serpentine belt.
  4. Disconnect the radiator inlet hose from the water pump.
  5. Unfasten the water pump pulley bolts/screws and remove the pulley.
  6. Remove the water pump pulley retaining bolts, then remove the pump from the vehicle.
  7. Remove and discard the gasket and thoroughly clean the gasket mating surfaces

To install:
  1. Position a new water pump gasket, then install the pump. Secure using the water pump retaining bolts/screws and tighten to 11 ft. lbs. (15 Nm), plus an additional 80 degree rotation.
  2. Install the water pump pulley and retaining bolts. Tighten to 115 inch lbs. (13 Nm).
  3. Install the serpentine drive belt.
  4. Connect the radiator inlet hose to the water pump.
  5. Connect the negative battery cable.
  6. Fill the cooling system. Start the engine and check for leaks.

5.7L ENGINE
  1. Unplug the electrical connector from the cooling fan.
  2. For 1993-95 vehicles, remove the right side cooling fan.
  3. For 1996-98 vehicles, remove both cooling fan assemblies.
  4. Place a suitable drain pan under the vehicle, then remove the block coolant drain plug and the knock sensor. Drain the radiator.
  5. Install the drain plug and knock sensor.
  6. Remove the air intake duct and air cleaner.
  7. Disconnect the upper and lower radiator hoses from the water pump.
  8. Remove the heater hoses from the water pump and throttle body.
  9. Unplug the electrical connector from the coolant sensor.
  1. Unfasten the retainers and reposition the ignition coil and bracket.
  2. If equipped, remove the air pump and bracket.
  3. Unfasten the water pump attaching bolts, then remove the water pump and discard the gasket. Remove the shaft coupling and water pump driveshaft seals, if necessary.
  1. Thoroughly clean the gasket mating surfaces
To install:
  1. If removed, install the shaft coupling and water pump driveshaft using J 39089 or equivalent water pump driveshaft O-ring installer.
  2. Install the water pump with a new gasket. Tighten the bolts to 30-32 ft. lbs. (41-43 Nm).
  3. If equipped, install the air pump and bracket.
  4. Reposition and secure the ignition coil and bracket.
  5. Attach the coolant sensor connector.
  6. Connect the heater hoses to the water pump and throttle body.
  7. Connect the upper and lower radiator hoses to the water pump.
  8. Install the air cleaner and air inlet duct.
  9. Install the electric cooling fan(s), then attach the electrical connector.
  10. Refill the cooling system.
  11. Connect the negative battery cable, then start the engine and check for leaks.


Hope helps (remember rated this).

Jul 01, 2010 | 1995 Chevrolet Camaro

1 Answer

How do i take off the old water pump on 1996 geo metro 4 cyl?


Removal & Installation
  1. Disconnect the negative battery cable.
  2. Drain the cooling system.
  3. Remove the air cleaner.
  4. Remove the suction pipe bracket for the A/C compressor, if equipped.
  5. Loosen but do not remove the 4 water pump pulley bolts.
  6. Raise and safely support the vehicle.
  7. Remove the lower splash shield.
  8. Remove the A/C compressor drive belt, if equipped.
  9. Remove the alternator drive belt.
  10. Remove the crankshaft and water pump pulleys.
  11. Remove the timing belt.
  12. Remove the oil level dipstick and tube.
  13. Remove the alternator adjusting bracket from the water pump.
  14. Remove the water pump rubber seals.
  15. Remove the water pump mounting bolts and nuts and remove the water pump from the engine.


ae1b66e.gif
Water pump mounting location

  1. Clean the gasket mating surfaces thoroughly.
  2. Check the water pump by hand for smooth operation. If the pump does not operate smoothly or is noisy, replace it.
  3. Install the pump using a new gasket. Tighten the bolts to 115 inch lbs. (13 Nm).
  4. Install new rubber seals.
  5. Install the upper alternator adjusting bracket and tighten the bolt to 17 ft. lbs. (23 Nm).
  6. Install the oil level dipstick and tube.
  7. Install the timing belt.
  8. Install the water pump and crankshaft pulleys. Leave the water pump pulley bolts hand-tight.
  9. Install the alternator drive belt.
  10. Install the lower alternator cover plate and tighten the bolts to 89 inch lbs. (10 Nm).
  11. Install the A/C compressor drive belt, if equipped.
  12. Install the lower splash shield and lower the vehicle.
  13. Tighten the water pump pulley mounting bolts to 18 ft. lbs. (24 Nm).
  14. Adjust the water pump drive belt tension and tighten the alternator adjustment bolt to 17 ft. lbs. (23 Nm).
  15. Install the suction pipe bracket for the A/C compressor, if equipped.
  16. Install the air cleaner.
  17. Refill the cooling system.
  18. Connect the negative battery cable.
  19. Start the engine and check for leaks.


83667f6.gif Water pump assembly showing rubber seal location


  1. Disconnect the negative battery cable.
  2. Drain the cooling system.

    CAUTION When draining the coolant, keep in mind that cats and dogs are attracted by the ethylene glycol antifreeze, and are quite likely to drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantity. Always drain the coolant into a sealable container. Coolant should be reused unless it is contaminated or several years old.

  3. Remove the air cleaner assembly.
  4. Loosen but do not remove the four coolant pump pulley bolts.
  5. Raise and support the vehicle safely.
  6. Remove the lower splash shield.
  7. Remove the air conditioner compressor drive belt.
  8. Remove the lower alternator cover plate bolts, loosen the alternator adjusting bolt, and remove the drive belt.
  9. Remove the crankshaft pulley.
  10. Remove the coolant pump pulley.
  11. Remove the timing belt.
  12. Remove the oil level dipstick and guide tube.
  13. Remove the alternator adjusting bracket from the water pump.
  14. Remove the water pump rubber seals.
  15. Remove the water pump mounting bolts and nuts. Remove the water pump from the vehicle.
To install:
  1. Clean the gasket mating surfaces thoroughly.
  2. Check the water pump by hand for smooth operation. If the pump does not operate smoothly or is noisy, replace it.
  3. Install the pump using a new gasket. Tighten bolts to 115 inch lbs. (13 Nm).
  4. Install new rubber seals.
  5. Install the upper alternator adjusting bracket and tighten bolt to 17 ft. lbs. (23 Nm).
  6. Install the oil level dipstick and guide tube.
  7. Install the timing belt.
  8. Install the water pump pulley and leave the bolts hand tight.
  9. Install the crankshaft pulley.
  10. Install the water pump/alternator drive belt.
  11. Install the lower alternator cover plate and tighten bolts to 89 inch lbs. (10 Nm).
  12. Install the air conditioner compressor drive belt by releasing the tensioner pulley and installing belt.
  13. Install the lower splash shield and lower vehicle.
  14. Tighten water pump pulley mounting bolts to 18 ft. lbs. (24 Nm).
  15. Adjust the water pump drive belt tension and tighten alternator adjustment bolt to 17 ft. lbs. (23 Nm).
  16. Install the air cleaner assembly.
  17. Refill the cooling system.
  18. Connect the negative battery cable.
  19. Start the engine and allow it to reach operating temperature. Check for leaks and refill cooling system as necessary.

Mar 06, 2010 | 1996 Geo Metro

1 Answer

I need to know how i can get to my water pump and what all i need excatly to fix it


  1. Disconnect the negative battery cable.
  2. Drain the coolant into a suitable container.
  3. Disconnect the radiator outlet hose.
  4. Remove the radiator fan motor assembly.
  5. Remove the accessory drive belts.
  6. Remove the timing belt, tensioner and camshaft angle sensor. Refer to the procedure in this section for removal and installation steps.
  7. Remove the left side camshaft pulley(s) and left side rear timing belt cover. Remove the tensioner bracket.
  8. Disconnect the radiator hose and heater hose from the water pump.
  9. Remove the water pump retainer bolts.
  10. Remove the water pump.

To install:
  1. Clean the gasket mating surfaces thoroughly. Always use new gaskets during installation.
  2. Install the water pump and tighten the bolts, in sequence, to 7-10 ft. lbs. (10-14 Nm). After tightening the bolts once, retighten to the same specification again.
  3. Inspect the radiator hoses for deterioration and replace as necessary. Connect the radiator hose and heater hose to the water pump.
  4. Install the left side rear timing belt cover, left side camshaft pulley(s) and tensioner bracket.
  5. Install the camshaft angle sensor, tensioner and timing belt.
  6. Install the accessory drive belts.
  7. Install the radiator ran motor assembly.
  8. Install the radiator outlet hose.
  9. Fill the system with coolant.
  10. Connect the negative battery cable.
  11. Start the engine and allow it to reach operating temperature.
  12. Check for leaks.





Jan 20, 2010 | 1992 Subaru Legacy

1 Answer

Need to replace water pump


To replace the water pump on a Cavalier follow these steps:

* Disconnect negative battery cable

* Drain the cooling system into a proper container.

* Remove the serpentine belt

* Remove the alternator and bracket

* Unscrew the water pump pulley mounting bolts and remove the pulley.

* Unfasten the mounting bolts and remove the water pump.

* Use a putty knife and thoroughly clean old gasket material off of gasket mounting surface.

* Place a small bead of RTV sealant on new water pump.

* Put on gasket and make sure bolt holes are lined up properly.

* Install the water pump and tighten the retaining bolts to 18 ft lbs.

* Install the water pump pulley and then go back to retaining bolts and tighten to 22 ft lbs.

* Reinstall alternator and bracket.

* Put on serpentine belt.

* Fill cooling system to proper level with coolant.

* Connect battery cable, start the engine, and check for leaks.

Sure hope this helped you and good luck with the repair.

Jul 20, 2009 | 1999 Chevrolet Cavalier

1 Answer

2002 ford taurus wtaer pump


Removal & Installation 3.0L (2V) To Remove:
  1. Drain the engine cooling system.
  2. Loosen the water pump pulley.
  3. Remove the bolt and the nut and position the roll restrictor bracket out of the way.
  4. Remove the accessory drive belt.
  5. Remove the generator.
  6. Remove the bolt and the accessory drive belt tensioner.
  7. Remove the nut, the bolt and the support bracket.
  8. Remove the bolts and the water pump pulley.
  9. Disconnect the water pump inlet hose and the crankshaft position sensor electrical connector.
  10. Remove the bolts and the water pump, and clean the sealing surfaces
To Install:
  1. Install the water pump. Tighten bolts in the sequence shown:
    1. Tighten numbers 1-7 to 18 ft.-lbs. (25 Nm)
    2. Tighten numbers 8-12 to 89 in.-lbs. (10 Nm)
    3. Connect the crankshaft position sensor electrical connector and the water pump inlet hose
    4. Install the support bracket.
    5. Install the accessory drive shaft tensioner.
    6. Install the generator.
    7. Install the roll restrictor bracket, bolt and the nut.
    8. Install the water pump pulley.
    9. Install the accessory drive belt.
    10. Connect the battery ground cable.
    11. Fill the engine cooling system.

9de9feb.gif
Water pump bolt torque sequence (3.0L (2V) engine)

Jul 04, 2009 | 2002 Ford Taurus

1 Answer

Looking for directions, pictures, on how to change water pump


Water Pump Removal & Installation 3.0L (2V) To Remove:
  1. Drain the engine cooling system.
  2. Loosen the water pump pulley.
  3. Remove the bolt and the nut and position the roll restrictor bracket out of the way.
  4. Remove the accessory drive belt.
  5. Remove the generator.
  6. Remove the bolt and the accessory drive belt tensioner.
  7. Remove the nut, the bolt and the support bracket.
  8. Remove the bolts and the water pump pulley.
  9. Disconnect the water pump inlet hose and the crankshaft position sensor electrical connector.
  10. Remove the bolts and the water pump, and clean the sealing surfaces
To Install:
  1. Install the water pump. Tighten bolts in the sequence shown:
    • Tighten numbers 1-7 to 18 ft.-lbs. (25 Nm)
    • Tighten numbers 8-12 to 89 in.-lbs. (10 Nm)
  2. Connect the crankshaft position sensor electrical connector and the water pump inlet hose
  3. Install the support bracket.
  4. Install the accessory drive shaft tensioner.
  5. Install the generator.
  6. Install the roll restrictor bracket, bolt and the nut.
  7. Install the water pump pulley.
  8. Install the accessory drive belt.
  9. Connect the battery ground cable.
  10. Fill the engine cooling system.
2918819.gif
Water pump bolt torque sequence (3.0L (2V) engine)

Jun 26, 2009 | 2001 Ford Taurus

1 Answer

How Do i replace Water Pump on 98 Chevy Metro


  1. Remove the negative battery cable.
  2. Drain the engine cooling system.
  3. Remove the air cleaner assembly.
  4. Remove the A/C compressor suction pipe bracket (if equipped).
  5. Loosen four water pump pulley bolts. Do not remove the bolts.
  6. Raise the vehicle. Support the vehicle. Remove the right lower splash shield.
  7. Remove the right lower splash shield.
  8. Remove the A/C compressor drive belt (if so equipped) by releasing the tensioner pulley and removing the belt from the crankshaft and compressor pulleys.
  9. Loosen the generator adjusting bolt (1), pivot the generator and remove the water pump/generator drive belt.
  10. Remove the crankshaft pulley.
  11. Remove the water pump pulley (four bolts).
  12. Remove the timing belt.
  13. Remove the oil level indicator (dipstick) guide tube.
  14. Remove the upper generator adjusting bracket from the water pump (one bolt).

    1. Remove the rubber seals from the water pump.
    2. Remove the water pump mounting bolts and nuts.
    3. Remove the water pump and gasket from the vehicle.
    4. Clean the water pump and the gasket mating surfaces.
    5. Install the water pump.
    6. Secure the water pump with mounting nuts and bolts. Tighten Tighten the water pump mounting nuts and bolts to 13 Nm (115 ft. lbs.).
    7. Install new rubber seals (1) to the water pump (2).
    8. Install the upper generator adjusting bracket to the water pump (one bolt).
        • Tighten the upper generator mounting bracket bolt to 23 Nm (17 ft. lbs.).
      1. Install the oil level indicator (dipstick) guide tube.
      2. Install the timing belt.
      3. Install the water pump pulley.
      4. Finger-tighten the four bolts.
      5. Install the crankshaft pulley.
      6. Install the water pump/generator drive belt to the crankshaft, water pump and generator pulleys.

Nov 20, 2008 | 1998 Chevrolet Metro

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

132 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lexus Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

ROBERT GARCIA
ROBERT GARCIA

Level 3 Expert

874 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Lexus Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...