Question about 1999 Mazda 626

Open Question

Undoing the bonnet lining of mazda 626

Hi please does anyone know how do you undo the bonnet lining studs on a mazda 626 as need to access the washer wiper tubes.

Posted by on


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How do you open the bonnet to find the washer bottle

hi you cant open the bonnet there isnt one what you have to do is get a plain screwdriver and undo the grill underneeth the windscreen you turn the two clips and take the grill off and you will see the top of the washer bottle a bit tricky first time round

Jun 23, 2014 | Smart fortwo Cars & Trucks

1 Answer

I 2 have a problem with my hold light when i drive far off it starts flashing hold & jerks into gear i have a mazda 626 1994 i undo the battery it quits 4 a while what could it b 7 will it b expen

You describe a internal transmission failure Check the transmission fluid what is the color if its blackish then you have transmission failure. Your fix is another transmission rebuilt

Feb 24, 2012 | 1994 Mazda 626

1 Answer

Just had harmonic balancer put on and new belts he fogot the loctite glue so now has to undo bolt and put that on dur! but i am hearing a squeak in the wheel right hand drivers side AU car of my 1997 626...

it sounds like your brakes need to be replaced. the squeaking is actually a brake pad indicator rubbing on the rotors letting you know that the pads are low an need to be changed soon. if you let this go on for too long you may damage the rotors and spend a lot more money than just a simple brake job.

Mar 05, 2011 | 1997 Mazda 626

2 Answers

I need a 2001 Mazda 626 6 Cylinder Repair Guide....... does anyone know where I can download one for free??

Hi! There seems to be no site for a 2001 mazda 626 cylinder repair. Try haynes or chilltons manual from the bookstore or autoparts supply. Hope this helps and have a good one!

Jun 10, 2010 | Mazda 626 Cars & Trucks

1 Answer

Code 17 on a mazda 626 1992 lx what does it mean

The OBD-1 two digits trouble codes listed 'code-17' as:
Oxygen sensor.

This means that the fuel and ignition systems performance are in need of attention.

1.Distributor Cap: remove the 3-bolts holding the distriboutr to its body.
2. Inspect the distributor cap for cracks, and the roror-button is not worn or broken.
3. Inspect the distributor-cap terminals are not corroded or charred. Replace if charred. Clean them out if corroded.
4. Check the distributor-rotor for cracks or corrosion on its tip, and lesser spring tension.
Replace as necessary.
5. Reverse steps 1-4 to re-install distributor cap. Be sure to remove and replace the plug wires from the old distributor-cap to the new distributor-cap one-by-one. If not, the engine would not run.

1. Undo the top clips holding the fuel-filter hose, and undo the lower clips also.
2. Take out the fuel-filter from its mount.
3. Replace the fuel filter as necessary.(please not the way it was mounted) Reverse removal for installation.

Dec 11, 2009 | 1992 Mazda 626

1 Answer

I had an accident need a new bonnet my husband wants to try and fix it we need instruction and what tools do we need

If you have the replacement bonnet, & a regular socket set, it's a simple job of un-plugging the wash wipe tubes, and then undoing the hinges.
It's easier to use a small ratchet, to undo the bolts. Three or four each side, I forget. With more than likely, a 10mm socket.
Then it'll just come off in yer hand.
Then it's just the small issue of making sure the hinges aren't too badly mis-aligned, and 'marry up' with the bonnet fixing holes.
Then you need to close the bonnet to make sure it lines up with the rest of the car.
If it doesn't, then you need to bend the hinges, gently and slowly, with a big heavy bar, prefferably. But don't get too excited.
Then it's just a matter of repeating that, until it sits right.
Good luck with that.

Jul 26, 2009 | 2004 Ford Focus

2 Answers

How to replace Air Filter in 1998 Mazda 626, 4 Cyl

There is more then 2 clips, look carefully feel around, you will find them. Unclip and then pull the cover up. Just remove the filter and replace with new one . also make sure that the little rubber gasket is seated properly. One last thing bring a vacum cleaner. When you access the filter you may find dirt and dead bugs in there so vacum it out. good luck

Jun 05, 2009 | 1998 Mazda 626

1 Answer

A/c charge

hi valve is in engine compartment in front of driver.
lo valve is in front of radiators take the black plastic off near bonnet lock and you will see it

Jun 01, 2009 | 2000 Mazda 626

1 Answer

Gearbox removel mazda 626 1991

yes, that is what you do. You are almost there, keep going.

Feb 27, 2009 | 1991 Mazda 626

3 Answers

I can't find my antenna

silly as it may sound .some makers did use either bonnet or boot lid as an antenna.

Jun 09, 2008 | 2001 Mazda 626

Not finding what you are looking for?
1999 Mazda 626 Logo

Related Topics:

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts


Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8269 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides