Question about 2007 Chevrolet Uplander LS Minivan

1 Answer

Replaced rear brakes and now the tires don't move.

Posted by on

  • yadayada
    yadayada May 11, 2010

    then you did it wrong, pull it back apart and repair as stated in the service manual

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 811 Answers

Bleed system, check to make sure proper brakes where installed

Posted on Sep 12, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to fix rear studs


,First,put block under front tires to keep from moving.If you have rear drum brakes,then you will need to remove hub,Jack up and secure,then remove tire,remove wheel speed sensor,if equipped.remove brake drum,bearing and spindle assembly.To remove stud and replace,you will have to turn bearing and align bad stud so it has room to be removed.get a hammer and a piece of wood to put over stud and knock out,don't use a piece of metal,could mess up end and make hard to get out.After you get new stud in ,get lug nut and tighten to pull stud in.A punch smaller than stud will work.

Aug 16, 2012 | 2001 Ford Focus

1 Answer

Brakes freezing in reverse and back right tire won't move by hand when jacked up


Sounds like you have a stuck caliper, they run $35-50 for the rears on that vehicle, They are not that difficult to replace, just be sure to bleed the brakes well after replacing it and check for leaks. If it has been like this for a long while. I would inspect the brake pads, and rotor while your there and replace them if they are worn.

May 11, 2012 | 1997 Plymouth Voyager

1 Answer

I have a 2005 Jeep Grand Cherokee and when I leave in the morning their is a vibration in the front tires that lasts about 10-20 seconds.It feels like the tires are skipping


If it's a vibration, it might be a brake pad staying in contact with the disk. Normally the pads push away when the car starts moving. (A normal condition called "runout") Try stopping your Jeep tonite by using only rear brakes. (hand brake) Don't step on the brake pedal at all. Then see if it does it in the morning. Don't step on the brake pedal in the morning till the test 20 sec's is over.

If the problem is a thump thump sound it's probably a tire flat spot from setting. Have the tires just been replaced? Could be a softer tirs material.


Jul 18, 2011 | 2005 Jeep Grand Cherokee

1 Answer

Noise on the right front side when braking. Make: Ford Fiesta 1.4 2008.


Time for a brake Job? Drive a small cheap car hard and you can run the brakes off quick. Real brakes come with real cars and these light cars have small brakes and if run hard or two footed can wear out quickly. Light niose can be rust wiped off the rotor after parked awhile then driven. Some brake rotors are different alloy and rust more than others and even a car just like yours might not do it. If the inspection doesnt find loose or broken brake parts cooked or craked, rim and tire problems can make noise move the tire to the back and the rear on the front run again to see if the problem moves to the rear. replace the broken parts and try again

Aug 11, 2009 | 2007 Ford Focus (3 Door) Hatchback

3 Answers

My rear left tire of 2001 Pontiac Montana will not turn


sounds like a bad set of wheel bearings. check them for ware.

Jun 11, 2009 | 2001 Pontiac Montana

1 Answer

Rear axle bearing replacement



REAR WHEEL BEARING/ HUB

Removal Procedure
  1. Raise the vehicle. Refer to Vehicle Lifting in General Diagnosis.
  2. Remove the wheel and the tire. Refer to Tire and Wheel Removal and Installation in Wheels, Tires and Alignment.
    1. Remove and support the brake caliper. Refer to Brake Caliper Replacement (Front) or Brake Caliper Replacement (Rear) in Brakes.
    2. Remove the brake rotor. Refer to Brake Rotor Replacement in Disc Brakes.
    3. Remove the ABS sensor wire connector.
    4. Remove the four bolts from the control arm.
    5. Remove the hub and bearing from the control arm.
    6. Remove the brake shield from the control arm.
    7. Clean the control arm face and the bore before installing the hub and the bearing.
    Installation Procedure

    Notice: Refer to Fastener Notice in Service Precautions.
    1. Install the brake shield and the hub and the bearing to the control arm with the four bolts. Be careful not to drop the hub and the bearing, as it could be damaged. Reconnect the ABS sensor. Tighten the hub and bearing bolts to 70 Nm (52 ft. lbs.).
    2. Install the brake rotor. Refer to Brake Rotor Replacement in Disc Brakes.
    3. Install the brake caliper. Refer to Brake Caliper Replacement (Front) or Brake Caliper Replacement (Rear) in Disc Brakes.
    4. Install the wheel and the tire. Refer to Tire and Wheel Removal and Installation in Wheels, Tires and Alignment. Tighten the wheel nuts to 140 Nm (100 ft. lbs.).
    5. Lower the vehicle.

Feb 14, 2009 | 2002 Pontiac Bonneville

2 Answers

2002 neon rear driver's tire is locked and won't move


sounds like the parking brake cable is stuck on the side, the first step, and the easiest step it to locate the cable behind the tire and really spray it with "WD-40" or "PB Blaster". That is to see if the cable can become free. If that doen't work, than you have to manualy de-adjust the brakes, ny locating a small rubber plug, rectangular in shape and using a brake adjusting tool, (availabel at most auto part stores) to "turn back" the adjusting screww inside the drum.

Jan 01, 2009 | 1998 Nissan 240SX

1 Answer

Rear brakes


either the cyl isnt moving or the shoes are not adjusted up far enough

Nov 05, 2008 | 1992 Saturn SL2

1 Answer

Rear tire seizing


Check rear bearing and be sure there is enough axle grease. A seized bearing will cause the problem you describe.

May 30, 2008 | 2001 Dodge Neon

Not finding what you are looking for?
2007 Chevrolet Uplander LS Minivan Logo

Related Topics:

115 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...