An expert who has achieved level 3 by getting 1000 points
An expert that got 10 achievements.
An expert that got 5 achievements.
An expert whose answer got voted for 500 times.
Re: how to replace the wiper insert at the back of
REMOVE RR WIPER BLADE
Raise the rear wiper blade to the position as shown in the
illustration where the meshing of the claw disengages with a clicking
sound. NOTE: Be careful not to break the claw.
Pull straight the rear wiper blade to vehicle's left from the wiper arm. NOTE: Do not fold the rear wiper arm with the rear wiper blade removed from it.
REMOVE REAR WIPER RUBBER
Place the rear wiper with the rear end of the rubber protruded from the blade stopper as shown in the illustration. NOTE: Do not pull out the wiper rubber forcibly, as the backing plates will become deformed or the blade claws will become damaged. HINT: The rubber can be easily pulled out by pushing the middhow to replace the wiper insert at the back of - f54b10a.gifthe blade.
INSTALL REAR WIPER RUBBER
Install the 2 wiper rubber backing plates to the rear wiper rubber. NOTE: Be carefhow to replace the wiper insert at the back of - 0dd144d.gifve and keep direction of curvature for correct replacement.
b. Insert the rear wiper rubber from the claw of the middle of the rear wiper blade into the rear end position.
c. After passing the rear wiper rubber through the rear end side claw,
protrude it from the rear end stopper and pass it through the front tip
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
the wiper motors have a sustain function inside
this magic switch, keeps wiper going it driver kill it with the switch.
preventing mid windows, stops. (safety and vision issues)
so that switch can break, and do what you said.
ive actually rebuilt them. and fixed the switch, many look mangled .
its inside the motor cover , below the wires connected there.
fix it, or replace it.
or the start up wire is hot all time.
the start up wire is the switch wire.
you turn off the wiper switch and its output goes to 0v, that be good
if stuck at 12v, its bad.
one way to check that is pull the switch connector (combo)
does wiper stop, yes, bad wiper switch
no,then bad wiper motor guts.
The wiper arm has a cover on the left end that pops up after gently spreading the two bottom sides apart. That allows the arm to swing out for cleaning the window or replacing the blade. The wiper blade assembly attaches to the end of the arm . It is pressed in and will pop out with a little force rotating the left side away from the arm. It pops back in with a little push. The arm remains attached to the rotating shaft assembly. I believe you can then replace just the rubber blade and not the whole blade assembly, if that is your fancy. Dave
programing a remote is not hard but it is timing is every thing! set up. driver's door open all others closed. all movements are done at one second intervals. 1 insert the key in the ignition and remove it twice 2 close and open the door twice. 3 insert and remove the key once 4 close and open the door twice. 5 insert the key 6 close door 7 rotate key to run back to off and remove. (locks should cycle once) 8 press both the lock and unlock buttons for a second on the remote. 9 press the remote's lock button (locks should cycle once more)
For 2005 Toyota Corolla (and Matrix), the location of the cabin air
filter is inside of the drawer (passenger side). Open the drawer, you
will see a screw on the RIGHT hand side. Unscrew it with a cross shape
screw driver. Unlock the drawer from the screw holder. And take the drawer out of the cabin. After the removal, you will be able to see the location of the cabin air filter.
There is a lock at each side of the filter cover. For each side, use two fingers to pinch the lock and pull out the cover. You will see the old filter after removing the cover. Pull it out, and insert your new filter.
Put the cover back. Make sure the two locks are firmly locked. Put the drawer back. To make this work easier,
you may lock the bottom of the drawer first, as there are TWO locks on
each side of the bottom drawer. Close the drawer to see if the position
is right. Place the screw back, that's all
Three things you can replace depend on your budet
1) you can replace whole wiper blabe assembly by lift up the cover at the bottom end of the bale assembly and un-screw the nut and raplace whole assembly with arm , wiper insert etc ... with the new one This way cost you more.
2) on hte middle of the whole wiper blade assy has the flexible section, you can un-screw 2 small philipe pan head screw with screw driver and disconnect the top section with the wiper blade insert (rubber)
3) slide wiper blade insert out of the holder, becareful with 2 small steel blade will hole your rubber insert inside the wiper frame. Slide new rubber insert in the frame .
A new wiper motor assembly comes with the linkage arm installed.
Before servicing the vehicle, refer to the Precautions Section.
Remove the windshield wiper mounting arm and pivot shaft
Do not remove the wiper motor linkage arm from the wiper motor
assembly. If the arm is removed, the wiper arms may not park in the
Use a suitable tool to separate the wiper linkage arm from the wiper mounting arm and pivot shaft assembly.
Remove the 3 bolts and the wiper motor.
Fig. Wiper motor and linkage
Install wiper motor and bolts.
Tighten wiper motor bolts to 10 ft. lbs. (13 Nm).
Install windshield wiper mounting arm and pivot shaft.
Check wiper operation.
Rear Wiper Motor - Removal & Installation
Remove the rear pivot arm.
Remove the rear wiper motor shaft nut cover
Remove the rear wiper motor shaft nut.
Open the lift gate window.
Remove the rear wiper motor cover trim panel.
Disconnect the electrical connector.
Remove the 2 rear window wiper motor nuts
Remove the rear window wiper motor.
Fig. Rear wiper motor view-2008 model shown, other years similar
Install rear wiper motor and tighten mounting nuts to 62 inch lbs. (7 Nm).
Reconnect the electrical connector.
Install wiper motor cover trim panel.
Install rear wiper pivot arm tighten nut to 53 inch lbs. (6 Nm).
this either has a nut on the base of the arm that needs to be removed or if no nut. then pull the arm away from the glass and there will be a meatal tab at the base of the arm that will slide to the side with this slid to the side the wiper arm is unlocked and will pop right off