Question about 2000 Oldsmobile Bravada

Open Question

Replacing water pump 2000 olds bravada 4.3 Hub

Replacing water pump 2000 olds bravada 4.3 Hub bearing/bolf

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Old fuel pump had three prong plug. new one has four prongs. what do i do with the fourth wire?


How to Install the Fuel Pump E3992M in 1998-2005 ...

? 4:55
www.youtube.com/watch?v=sRq2ohp8A7o
Apr 20, 2012 - Uploaded by Airtex Pumps 2001-98 OLDSMOBILE BRAVADA 262 (4.3L) ... is committed to providing the most up-to-date, in-depth fuel pump replacementinformation that ...

Oct 10, 2015 | 2000 Oldsmobile Bravada

1 Answer

Whats the size of the socket i need to replace my front hub bearing on a 2002 oldsmobile bravada


easy way get the socket is to go any auto parts store except napa they have a hub socket loaner set

Mar 19, 2015 | 2002 Oldsmobile Bravada

1 Answer

How to replace front wheel bearing?


old post, but you are first to say front. many others fail to say end of car.

is your car 4wd, as 2wd is different rules. so...??????

I toss coin land on 4WD.

2000 front wheel bearing

got it.

the 2000 year, is important.

this year is the last year, before non untized hubs.

http://www.fixkick.com/hubs/FW_BEARINGS.html#newer



my posts is for stock cars. only, and USA spec, cars.

other countries, evolve this in different years.



2000 (never 2001+)

fsm quotes



  1. Before servicing the vehicle, refer to the Precautions section.


  2. Remove or disconnect the following:



    • Front wheel


    • Brake caliper and rotor


    • Locking hub or hub drive flange, if equipped,(it is)


    • Hub grease cap, if equipped


    • Wheel speed sensor, if equipped (ABS)


    • Wheel bearing lockwasher


    • Wheel bearing locknut (ring) and inner washer


    • Wheel hub and bearing assembly (slide hammer?)


    • Wheel hub oil seal


    • Wheel bearing oil seal


    • Snapring




  3. Press the wheel bearing and race out of the hub.


reverse is same but the lock ring must be set

to 123-180PSI. stop tightening above 123 at first alignment hole in lock ring..

Jun 26, 2014 | 2000 Suzuki Grand Vitara

1 Answer

2000 ford f250 front hub dry


The hub should have grease in the taper bearings that go on the stub axle. If the grease was missing and the bearings were dry and rusted then the grease seal in the hub had failed and water was let into the bearings. Replace with new bearings and repack with a water resistant grease. Fit new seal .

Apr 01, 2013 | Cars & Trucks

1 Answer

I have a 2000 olds bravada that I am working on it has spark,and getting fuel. Dos this vehicle have a chain or belt


The 4.3 engine has a chain. Cover will have to come off to check timing marks. Procedure is pasted below.

jturcotte_1089.gif
4.3L Engine

  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:

    Negative battery cable
  3. Drain the engine cooling system.
    WARNING The outer ring (weight) of the torsional damper is bonded to the hub with rubber. The damper must be removed with a puller which acts on the inner hub only. Pulling on the outer portion of the damper will break the rubber bond or destroy the tuning of the unit.

    Crankshaft pulley and damper
    Water pump assembly Oil pan, loosen only Crankshaft Position (CKP) sensor, if equipped Front cover bolts and the reinforcements, if equipped Front cover from the engine

Feb 23, 2011 | Oldsmobile Bravada Cars & Trucks

1 Answer

How to remove the right side axel shaft on a 98 olds bravada


1. Raise and support vehicle, then remove tire and wheel assembly. 2. Install a brass drift or a screwdriver to prevent the rotor from turning, Fig. 7 . 3. Remove axle nut and washer. 4. Remove stabilizer shaft or link from control arm. 5. Remove nut from ball joint, then separate ball joint from steering knuckle using separator tool No. J-36226, or equivalent. 6. Remove drive axle from hub and bearing assembly using front hub spindle remover tool No. J-28733-A, or equivalent, Fig. 8 . 7. Remove drive axle from transaxle using axle shaft remover puller tool Nos. J-33008, J-29794 and slide hammer tool No. J-2619-01, or equivalents, if necessary, Fig. 9 . INSTALLATION 1. Install drive axle into the transaxle using seal protector J-37292-B, or equivalent 2. Seat snap ring by placing a screwdriver into the groove on the joint housing and tapping until seated, Fig. 9 . 3. Grasp the inner housing and pull outward. If the snap ring is properly seated, the axle will remain in place. 4. Install drive axle into hub and bearing assembly. 5. Install lower ball joint to steering knuckle and tighten to specifications. 6. Install stabilizer shaft or link to control arm, tighten to specifications. 7. Insert a screwdriver or drift into caliper and rotor to prevent rotor from turning, Fig. 7 . 8. Install new hub nut and washer, tighten to specification. 9. Install tire and wheel assembly, then lower vehicle

Feb 13, 2011 | 1998 Oldsmobile Bravada

1 Answer

How to take fan off a water pump of a 2000 bravada oldsmobile


theres a special tool that holds the pulleys bolts then you can use a big wrench to turn it. you can get it on rental from auto zone.

Jan 28, 2010 | 2000 Oldsmobile Bravada

1 Answer

Grinding noise on 2002 Olds Bravada


Try making tight turns to the right and then to the left. see if the grinding noise comes and goes. It could be your C/V joint and they need to be replaced. The noise will only come when your making the tight turns, you don't have to go fast. Walking speed will do and you can hear it with the window open or someone walking beside the Bravada. Good luck and keep me posted. Be glad to help.

Jun 16, 2009 | 2000 Oldsmobile Bravada

2 Answers

1998 Olds Bravada


your fuel pump is going bad if you have to tap the tank with a hammer to get it to work again

Feb 10, 2009 | 1998 Oldsmobile Bravada

Not finding what you are looking for?
2000 Oldsmobile Bravada Logo

Related Topics:

271 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8270 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...