Question about 2002 Honda Odyssey

Open Question

Driver side power window cable has snapped. I need to get a new one but I need a diagram on how to install the new cable.

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

RE MY CRV 2003,(1) all the yellow lights outside the body are supposed to blink whenever i used the remote wireless key. However, for a week now, the lights do not blink anymore. (2) Cable snapped on...


Hi,
1) Look at the manual for the remote switch, there is an option to light up the signal light when you remotely push the button.

2) The window cable regulator part can be bought/order in your nearest Honda Parts Dealer, you could also ask any auto parts store for a replacement parts that you needed. bring your car to the nearest garage to install the new window regulator.

Hope that helps you out!

Aug 07, 2011 | 2003 Honda CR-V

1 Answer

Diagram to fix driver side window slid down. after take the door cover off, I find a cable not hooked to anything, but the motor does run


The cable snapped and you have to get a new or used window regulator. Common problem but no way to repair it.

Jun 14, 2011 | 1996 Honda Accord

1 Answer

A 2004 Ford Expedition Eddie Bauer driver side window not working


The entire assy. This uses a cable system and what you are hearing is the cable twisting and getting ready to snap. New units are available at Advance Auto parts

Jan 14, 2010 | 2004 Ford Expedition

1 Answer

Need to find a way to take off the drivers side window motor


Motor
  1. Disconnect the negative battery cable.
  2. Remove the door trim panel and watershield.
  3. Detach the motor wires at the multiple connector.
  4. Remove the motor retaining screws using Torx® drive bit set D79P–2100–T or equivalent, and separate the motor from the bracket and cable drum housing.
  5. Remove the motor from inside the door.
To install:
  1. Position the motor and drive to the cable drum housing and motor mounting bracket. Install the 3 motor screws and tighten.
  2. Connect the power window motor wiring.
  3. Connect the negative battery cable.
  4. Check window operation.
  5. Install the watershield and door trim panel.

Door Panel
  1. Disconnect the negative battery cable.
  2. Snap out the two door pull strap retaining screw covers. Remove the screws.

CAUTION To avoid breakage of the door pull covers, insert a small screwdriver diagonally between the pull strap and chrome bracket. Snap out both sides then remove.


  1. Remove the two screws on the front and rear side of the front door trim panel.
  2. Using the trim pad removing tool, pry the trim panel retaining clips from the door inner panel.

NOTE Do not use the front door trim panel to remove the trim clips from the door inner panel. Replace any bent, damaged or missing push pins.


  1. Remove the window regulator switch housing from the back of the front door trim panel. Lift up the housing and disconnect all connectors from the switch housing.
  2. Disconnect the driver seat regulator control processor switch if equipped.
  3. Twist out the interior lamp wire assembly.
To install:
  1. Ensure that the plastic watershield is secured to the door .
  2. Position the front door trim panel to the door. Connect the interior lamp wiring.
  3. Align door lock side to its mating slide on the sheet metal.
  4. Snap in the front door trim panel. Ensure all retainers fit properly. Install the two retaining screws on the front and rear side of the front door trim panel.
  5. Connect the driver seat regulator control processor, if equipped.
  6. Position the window regulator control switch housing and connect the switch connectors. Install it to the front door trim panel by snapping it in, or by installing the screw at the rear.
  7. Install the two retaining screws and pull strap covers.
  8. Connect the negative battery cable.
053777a.gif

Aug 27, 2009 | 2000 Lincoln Town Car

1 Answer

Need diagram for cables on power windows for 1998 pontiac grand prix


There is no diagram. You will have to buy a window regulator. If the cables are not in there right places on the regulator then something has broken and you need a new one. Hope this is helpful

May 07, 2009 | 1998 Pontiac Grand Prix

1 Answer

Inside door handle doesn't work (removing the driver side panel)


If you have power windows start by disconnecting your negative battery cable. Then you need to locate and remove the screws that hold your door handles in place (they may be hidden by snap in, or snap on clips). Once you remove the screws that hold the door handles, remove any wire connectors to the handles, if they're not power you will need a small hook (kinda like a knitting needle) to remove the window crank. A manual window crank is held in place by a clip on the base. Slide the hook behind the base and remove the clip. The door panel itself, is held on by snap in clips, and you will need a small pry bar to pull them from the door (try to gat as close to, or directly under the clips to prevent them from tearing out of the door panel). Once the clips are removed from the door, pull the panel upward to remove it from the door.

Install in reverse.

I hope this helps you, and I wish you luck on your repair.

May 04, 2009 | 1992 Chrysler New Yorker

1 Answer

1997 Nissan Altima Driver Power Window


Then power window regulator cable is snapped out its place ,you need to install new power window regulator for the door to fix this issue ...


Good luck...

Nov 06, 2008 | 1993 Nissan Altima

1 Answer

Electric window


You to install the motor to new power window assembly ,as the cable is snapped just the assembly and old motor to it it will work...



Good luck..

Aug 18, 2008 | 1997 Volkswagen Golf

2 Answers

Cable snapped on power window


This is too easy it took me 15 mins to do. only 6 bolts to remove. Just follow the directions. You can get the parts off the internet for about $60.00 just have to look.

The cable cuts into the plastic guides and over time the cut right through them. The bright side is they are easy to replace.
There are two bolts that hold the window to the regulator. Remove them and lift the window up and out of the way. You don't need to take it out, just secure it so it doesn't fall down. (tape it on the top going from one side to the other)
42140395.gif Then there are two bolts on the top and bottom of the regulator slide. Take them out, noting where the are as far as adjustment. You can use a scratch awl to scribe around the bolt heads to be sure you get them back as they were.
42140396.gif Then remove the three bolts holding the power window motor on and remove the guide and motor as an assembly. To install the new one, take the power window motor off the old regulator and install it on the new one.
42404005.gif Then install the regulator and power window motor assembly in reverse order of installation.

Jul 12, 2008 | 1997 Honda Accord

Not finding what you are looking for?
2002 Honda Odyssey Logo

Related Topics:

152 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...