Question about 2004 Ford Ranger

Open Question

Having problems removing a shifter knob

I have a 2004 ford ranger and just bought a new shifter knob yesterday for an upgrade on looks but cant get the old one off... any help?

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My gear shifts way to the right how would i fix that.


Is your truck an automatic? If your talking your shifter on your column, there is a lil, I would call it a wheel behind your dash up near where your shifter goes in. If you look up behind there, there will be a little wire that runs from behind your dash and at some point through a plastic piece with a wheel/knob in it. If your turn that knob it will change where your shifter reads depending on the direction you turn it. Hope that helps you out

Aug 01, 2012 | 1992 Ford Ranger

1 Answer

I have a 2004 Ford Ranger @WD. The therostat is stuck open and needs to be replaced. I have been told by a Ford shop mechanic taht we willhave to replace the whole housing at a cost of $250+? Does that...


No its not. Drain the system a bit, remove the housing, remove the thermostat, put in the new one, replace the gasket, put the housing back, top up the system.


2004 ford ranger 3 0 thermostat replacement Google Search

The thermostat is 20 bucks! The housing and gasket is 12 bucks!

Ford Ranger Thermostat

Oct 01, 2017 | 2004 Ford Ranger

1 Answer

How do i remove the manual gear selector on a 93 ranger


remove the knob or slide the rubber boot up the shifter. there are 4 screws under the floor mat that hold the boot in place. after the boot you should see four more bolts holding the shifter in place, they are usually 10mm socket. remove them and remove shifter from the top of trans.

Feb 07, 2010 | 1993 Ford Ranger SuperCab

1 Answer

I cannot get the head peice of the shift knob off the shift knob, i have it stripped to the metal parts and now i need to get it off of the threads, but i think it is locktighted. i ewnt to mod with a...


You are right. They usually put locktight on at the factory. take care not to break it, but it is hard not to. Try a rag around the knob and a good set of vise grips or channel locks. Good Luck

Jan 26, 2010 | 2002 Ford Ranger Regular Cab

4 Answers

Shifter knob broke and pulled up on 2004 Lincoln Aviator


Same problem. $800 quote from Dealer for a small plastic part that broke because of terrible design. Nice work Ford. They should be ashamed.

Jan 02, 2010 | 2004 Lincoln Aviator

1 Answer

I have a 2004 ford ranger. Wipers not functioning properly


you would have to remove the plastic cover from the steering column, and then replace the turn signal assembly. should only be a couple screws and a few electrical plugs. make sure you disconnect the negative(-) battery terminal untill you are done with the repair.

Oct 27, 2009 | 2004 Ford Ranger

1 Answer

How to remove gear shift knob on a 2004 ford ranger?


If You Are Talking About The Knob On A Manual Trans They Used To Screw On

Jul 11, 2009 | 2004 Ford Ranger

1 Answer

Shifter knob removal


the shift knob is glued and pressed on, the best way to remove it intact is to heat the knob with a heat gun and pull straight up with a lot of force, please be very careful because when the knob finally releases there is very good chance that you can hit yourself in the face, if the knob is not to be used again you cut a **** up the side with a dremal tool,

Sep 13, 2008 | 2008 Ford Ranger 2WD

Not finding what you are looking for?
2004 Ford Ranger Logo

Related Topics:

113 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...