Question about 2003 Ford Focus

1 Answer

Had a solid flywheel conversion and new crank sensors fitted and now the car wont start!!!1

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 432 Answers

Crank sensors not right or bad pickup on flywheel if it has one

Posted on Sep 13, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do we timer flywheel for gw2.8tci


Make sure the flywheel sensor is working.

Apr 21, 2017 | Cars & Trucks

1 Answer

How do I line-up the flywheel timing marks and where are they. I fitted new clutch and had to remove the flywheel


There should have been a dowel pin in crank flange so the flywheel would go back in the same spot. Is it a new flywheel? Was it balanced? There are no timing marks on the flywheel. Does the gear on the starter line up with the flywheel teeth? Does the engine turn over? Would like to help.

Jan 29, 2015 | Cars & Trucks

1 Answer

My jcb jz140 cut out when spining around and now say flywheel code 108 an wont start what can i do?


If the engine is turning over(cranking but not starting) then theres a chance you damaged your crank sensor. When u say spinning around do you mean you were 360 wheeling at a high rate of speed, because you could also have picked up debris in the bell housing that damaged or is obstructing the signal form the flywheel to the crank. Check the sensor cable and connections first if the car is cranking.

Oct 09, 2014 | Cars & Trucks

1 Answer

How do I set the crank sensor position on the flywheel after it has been removed.?


fly wheel wont change ,the crank position sensor picks up a magnetic puls created when the motor spins past the(CPS) and that reads that the motor is spinning

Sep 22, 2014 | Cars & Trucks

1 Answer

How do i check for the timing marks on the automatic flywheel for the vw passat v6 amx engine


Hi. The amx does not ahve a flywheel pick up. the crank sensor g28 is on the side of the block. The flywheel have offset bolts so can only be fitted in the correct position. The best way to set tdc is with a special tool that goes into the side of the block at g28 sensors hole, or to set tdc with a dial gauge on cylinder 1. I don't yhink the flywheel fitment is the issue with this vehicle. Have you disconnected the air mass meter and run the car to see if it is beter? The air mass meter commonly fails when disturbed during repairs.

Jan 15, 2014 | Volkswagen Passat Cars & Trucks

1 Answer

Cranksensor trouble on nissan navara 2006


there is almost no way to miss align the flywheel! did you checked side by side for proper fit and all the slots matched , if you didn't i would get one fro the same place and match the old one, Also did you remove the sensor before replacing the flywheel? if you didn't you may have a broken sensor.

Apr 07, 2012 | 2006 Nissan Navara 2.5

1 Answer

I have a 94' Chysler Newyorker, and when i go to start it or give it gas it either dies or trys to die. When in drive the RPM wont go over 1-1 1/2 &MPH wont go over 20. When in Neutral or Par


You replaced all those sensor,Your problem is mechanical, The timing may have slipped.If the timing belt is good and all on the mark,how the crank position sensor, The crank get its signal from the transmission flywheel,if the flywheel is cracked and lost its position then it does exactly what you describe . You either have a cracked flywheel or a jumped timing belt.The exhaust can be plugged also

Mar 19, 2012 | 1994 Chrysler New Yorker

1 Answer

Starter spins but wont crank motor put two different starters and does same


Remove the starter and inspect the teeth on the flywheel if the teeth are worn the transmission will req removing and a new flywheel fitting try putting the vehicle in gear and rocking it this will turn the engine and change the position of the flywheel then try to start

Oct 04, 2010 | 2000 Oldsmobile Intrigue

1 Answer

R@r engine an harness in vehical no start an p0355 code present no crank signal no rpm on monitor an none on cluster. test signal an has signal to ecm from crank sensor.wondering if maybe terminals could...


i will assume that on both engines the sensor is located at the lower
right side of the block and we don't know the year of the new engine
I believe the crank sensor gets it's signal from the flywheel so if the
flywheel is diffirent it could affect the signal.
I would call a salvage yard and ask if they have run into this before
they have interchange charts that tell you if a 96 fits a 99 or a 00
will fit an 02 if you change this or that. I hope this helps.
any other ? gimme a shout good luck

Jan 14, 2010 | Chevrolet Suburban 1500 Cars & Trucks

1 Answer

Jaguar xj8 will not start.


how old is the car, and how old is the engine you fitted.
later engine require old flywheel as crank senors are different.

Mar 11, 2009 | 1998 Jaguar XJ8L

Not finding what you are looking for?
2003 Ford Focus Logo

Related Topics:

107 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...