Question about 1983 Toyota Camry

1 Answer

How to change 1980 camry water pump without having to disconnect the engine mounts and moving the whole engine. There is little to no room to pull out water pump.

Posted by on

  • Anonymous Mar 15, 2014

    Change water pump

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 66 Answers

I can't remember exactally for that model - but it is sometimes required that you may have to loosen the mounts and jack up the engine from the underside - It all depends on how much room you have and how much you need - I wouldn't remove it, just jack it up until you have the space you need (If you have to) - Alot of foreign cars offer very little space to work in - Nature of the beast - so no, there's not a "quick-fix", but just use your common sense and remember the water pump isn't too terribly "deep"or "thick" and can ususally be worked into place...even a small space - if you can access the bolts...Common sense #1...Good luck.

Posted on Sep 12, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

When replacing the water pump on a 1997 toyota camry 2.7, do you have to remove the harmonic balancer?


no
2RZ-FE and 3RZ-FE Engines
  1. Disconnect the negative battery cable.
  2. Drain the cooling system.
  3. If equipped with an air conditioning compressor or power steering pump drive belts, it may be necessary to loosen the adjusting bolt, remove the drive belt(s) and move the component(s) out of the way.
  4. Remove the fluid coupling with the fan and water pump pulley.
  5. Remove the water pump.
To install:
  1. Clean the gasket mounting surfaces.
  2. Install the replacement water pump using a new gasket.
  3. Install the water pump pulley and fluid coupling with the fan.
  4. Install the removed engine drive belts.
  5. Fill the cooling system.
  6. Connect the negative battery cable. Start the engine and check for leaks.
  7. Bleed the cooling system.

Aug 13, 2017 | Toyota Cars & Trucks

2 Answers

I have a 2001 Hyundai Accent Automatic, can u please help me by answering. Does the whole engine/gearbox have to be lifted out together or can u pull the LHS wheel ect... off and remove gearbox that way?...


NOT at all you leave the engine in the car you use a engine support cradle to hold the engine upright so when you disconnect the engine mounts from underneath the engine stays supported. find out what supports the engine underneath , and will the gearbox fit when lower control arm ball joint removed.

Oct 18, 2010 | Hyundai Accent Cars & Trucks

2 Answers

How do you install the water pump on a 1991 toyota camry? Does the moter have to come out?


Remove the timing belt and then you can access the water pump. Medium difficulty. Don't attempt if not sure about timing belt r&r.

May 30, 2010 | 1991 Toyota Camry

2 Answers

Do I have to remove the whole power steering to install water pump?


I think on that model you have to remove the power steering pump pulley first before you can get to the rest of the power steering pump mounting bolts.
You can rent a special puller / installer from one from your local auto parts store.
Once you have pulled the pulley and removed the pump mounting bolts,just drop the whole pump unit with the hoses attached out of the way of the water pump.
Good Luck.

Nov 15, 2009 | 1990 Ford F150

1 Answer

How do i get to the water pump on a 1998 nissan altima


THE 2.4L AND 2.5L ENGINES.YOU HAVE TO SAFELY RAISE VECHICLE SUPPORT IT USING JACK STANDS.YOU HAVE TO REMOVE THE RIGHT HAND SPLASH SHIELD.THEN LOOSEN WATER PUMP PULLEY BOLTS LEAVE DRIVE BELT IN PLACE TO KEEP WATER PULLEY FROM TURNING WHILE LOOSEN PULLEY BOLTS.THEN YOU HAVE TO MOVE AC COMPRESSOR DONT DISCONNECT ANY REFRIGERANT LINES.JUST SET IT ASIDE THE ALTERNATOR AND ITS MOUNT ALSO HAS TO MOVED.THEN YOU ARE AT WATER PUMP.NOW THE 3.5L ENGINE WATER PUMP IS IN A TOUGH SPOT.YOU HAVE TO REMOVE ENGINE SPLASH SHIELD.REMOVE THE SUBFRAME BRACKET FROM THE RIGHT SIDE OF THE SUBFRAME ASSEMBLY. REMOVE THE INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM FROM THE ENGINE COMPARTMENT.REMOVE THE IPDMER UPPER COVER AND HARNESS COVER RELEASE THE TWO CLIPS.DISCONNECT THE ELECTRICAL CONNECTORS AND LIFT THE ASSEMBLY FROM THE CASE.REMOVE THE RADIATOR SHROUDS REMOVE THE DRIVE BELTS.REMOVE THE ENGINE COOLING FAN.REMOVE THE RADIATOR AND THE COOLANT RESERVOIR.REMOVE THE IDLER PULLEY AND THE POWER STEERING AND ALTERNATOR ADJUSTMENT BRACKETS.REMOVE THE FRONT ENGINE MOUNT.REMOVE COOLANT DRAIN PLUG FROM THE WATER PUMP SIDE OF THE ENGINE BLOCK.REMOVE CHAIN TENSIONER COVER AND THE WATER PUMP COVER FROM THE ENGINE FRONT COVER.REMOVE THE CHAIN TENSIONER.PULL THE LEVER DOWN TO RELEASE THE PLUNGER STOPPER TAB.INSERT A STOPPER PIN INTO THE TENSIONER BODY HOLE TO RETAIN THE LEVER IN THE RELEASED.NO CHAIN TENSION POSITION.MOVE THE PLUNGER INTO THE TENSIONER BY PRESSING THE CHAIN GUIDE AND PUSHING WITH A SCREWDRIVER.MAKE A GAP BETWEEN THE WATER PUMP GEAR AND THE TIMING CHAIN BY ROTATING THE CRANKSHAFT PULLEY 20 DEGREES COUNTERCLOCKWISE.REMOVE THE THREE WATER PUMP MOUNTING BOLTS.INSTALL 2 BOLTS SIZE M8 1.25 X 50 MM INTO THE WATER PUMP BOLT HOLES AND TIGHTEN THEM EQUALLY UNTIL THEY BOTTOM AGAINST THE CHAIN COVER.IT WILL BE NECESSARY TO ROTATE THE WATER PUMP SLIGHTLY TO ALLOW THE BOLTS TO DRIVE AGAINST THE REAR TIMING CHAIN CASE COVER INSTEAD OF THE BOLT HOLES.REMOVE THE WATER PUMP.CLEAN THE SEALANT FROM THE MATING SURFACE AND REPLACE THE O-RINGS.INSTALL THE OUTER O-RING WITH THE WHITE PAINT MARK FACING THE FRONT OF THE ENGINE AND THE INNER O-RING BLACK NEXT.APPLY A LIGHT AMOUNT OF OIL TO THE O-RINGS.TIGHTEN THE WATER PUMP BOLTS TO 62 - 89 INCH POUNDS.TIGHTEN WATER PUMP BOLTS EVENLY DONT OVER TIGHT OR YOU WILL DAMAGE WATER PUMP AND HAVE LEAKS.REINSTALL THE POWER STEERING AND ALTERNATOR ADJUSTMENT BRACKETS AND ANY OTHER COMPONENTS REMOVED FOR ACCESS TO THE WATER PUMP.REFILL THE COOLING SYSTEM.RUN THE ENGINE AND CHECK FOR LEAKS.YOU NEED TO BUY THE HAYNES REPAIR MANUAL.SO THE PHOTOS WILL HELP YOU WHEN REMOVING AND INSTALLING WATER PUMP.

Nov 14, 2009 | Nissan Altima Cars & Trucks

1 Answer

I have toyota camry 1991 when ever i will reverse the car the engine will stop and it will show the battery on dashboard i check the batrey and alternator they are ok.it takes long time to start again.


without seeing the car, hard to say. but if i get this right,make sure i get a little something extra in my stocking this x-mas.

broken motor mount??[allows the engine to move far enough that it is pulling a wire connection /or losing ground connection to battery. check and get back to me.

Nov 03, 2009 | 1991 Toyota Camry

2 Answers

Need to replace the oil pump on a 95 park avenue


You shouldn't have to for head gaskets, makes it easier but not necessary.
For oil pan, you may have too. Depending on how much room there is between pan and crossmember and if pan is in tranny. Some cars the oil pan is 1/4" behind tranny but don't think that is the deal on your car.

You can go to auzone.com and register for free. and you will have an AWESOME Full Free Online Repair Manual with everything you could need plus much more!

Aug 26, 2009 | 1995 Buick Park Avenue

1 Answer

Change water pump on 1995 toyota cor.le


alfred11s: No, you don't have to lift the motor. You do have to remove the right hand engine mounting insulator.
I will give you the procedure for the removal to access the pump:.
1.Drain engine coolant
2. remove right hand engine mounting insulator
3. Remove #2 and # 3 timing belt covers
4. Remove front engine mounting insulator as follows
a. remove hole cover
b. remove the 2 bolts from the mounting
c. remove the nut, the through-bolt and front engine mounting insulator
5. Remove the electric cooling fan
6.Disconnect engine wire remove the bolt and 2 nuts and disconnect the engine wire.
Water pump removal instructions:
1. Disconnect the crank sensor connector from the dipstick tube
2, Remove the dipstick tube and dipstick (only 1 bolt holds it)
3. Disconnect the water temp sensor from harness
4, Remove the two nuts and the # 2 water inlet from the hose.
5.Remove the three bolts which retain the water pump!
CAUTION! try to keep antifreeze off the timing belt. Put rags down and pack them where the coolant would normally spill.
WELL alfred11s: My answer should be a pleasant surprise.
Print it out and carry it out to the car.
If I've done well, maybe you can comment on what you think

Apr 29, 2009 | 1995 Toyota Corolla

1 Answer

Can I change the water pump on a 1997 Lesabre without removing the power steering pulley ? There is just one bolt the pulley seems to be preventing from me removing ... I was hoping maybe I could just...


disconnect the engine mount on the side and carefully raise that side of the engine, also remove the water pump pulley, u will need a PS pulley puller, u can borrow one form most discount auto parts stores for just a deposit.

Apr 19, 2009 | 1997 Buick LeSabre

1 Answer

How do i remove serpentine belt to change water pump?


There is a pulley thast moves around a little when the engine is running, this is the belt tensioner pulley, you will need either a special wrench or a ratchet to release the tension on the belt.

Jul 05, 2008 | 2002 Toyota Camry

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

73 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...