Question about 1984 Mazda 626

1 Answer

How to remove inlet manifold on mazda 626 1984 2 L

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 778 Answers

You should purchase a chiltons or haynes manual for your engine. But otherwise you should first disconnect the battery, then the fuel line, throttle linkage, then the injector connectors or throttle body if it's not EFI, and remove the intake manifold bolts in a cross pattern starting in the middle and working outward to the front and back, then you can use a putty knife or something similar to wedge in between the intake and the head to gently break the seal until you are able to remove the intake manifold.
I hop I understood and this post helps you.-

Posted on Sep 12, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Mazda b4000. 99 with 90 000 km. Sputters/backfires on deceleration? Cause?


Exhaust is leaking / broken somewhere. Inlet manifold has an airleak/ gasket blown.

Aug 12, 2015 | Mazda Cars & Trucks

1 Answer

Where is the egr valve


exhaust gas re circulation valve,is quite easy to spot,follow the small supplementary pipe from the exhaust manifold back towards the inlet manifold,and there is a small valve mechanism that is a gateway between the inlet /exhaust system integration.

Jun 01, 2014 | 1995 Mazda 626

1 Answer

P2004 INTAKE manifold runner stuck open control bank 1.


Hi there,
I have a Mazda 6 which recently had black smoke / soot coming from the exhaust. On inspection, the inlet manifold was stuck open. I have just had the garage replace the control solenoid for the inlet manifold and so far the car is running ok.

Apr 05, 2012 | Ford Focus Cars & Trucks

1 Answer

Where is the fuel filter located on a 2000 Mazda MPV?


the 2000 MPV doesn't have a fuel filter. You could try fitting one on the fuel line just before the injector rails. These are located under the the inlet manifold but you have to figure out which one is the inlet pipe and which one is the return pipe. You will need to disconnect the plastic air intake pipe in order for you to access the fuel supply lines. Hope this works.

Dec 27, 2010 | 2000 Mazda MPV

1 Answer

I can't find the oil filter on my 1995 mazda 626.


It should be behind the engine when you look from the front of the car. Normally underneath the inlet manifold.

May 05, 2010 | 1995 Mazda 626

1 Answer

Where is the starter located on 2000 mazda 626 lx 2.0


if u open the hood and stand on the right hand side of the car at the wheel facing the engine its on the right hand side of the gearbox under inlet manifold

Apr 02, 2010 | 2000 Mazda 626

1 Answer

How to change a starter on a 96 mazda 626 ?


Write down the radio's activation code prior to disconnecting the battery' s negative terminal.

Remove the air-intake duct and the air filter housing. (assuming this your car is 4-cylinder)
Remove the bracket that runs between the inlet manifold and the starter-motor.
The starter-motor is by the left-side of the transmission over the axle-shaft.
Disconnect its solenoid wire and the positive wire attached to the starter-motor.
Remove the three 14mm bolts holding it up.
Once taken out, exchange it for a rebuilt one at your local autoparts store.
Installation is reverse of removal.

Oct 03, 2009 | 1996 Mazda 626

1 Answer

How to remove and install a supercharger in a 96 mazda millenia I have found a used on and need to know how to remove and put back on car


The supercharger is bolted to the engine and driven by the fanbelt ,with a pipe in from the air filter and then a pipe out to the inlet manifold ,so after finding how to slacken belt adjuster its just a simple job to unbolt the supercharger ,but i have never done one on this model so i couldnt tell you what and where the bolts are .sorry to let you down but i havent worked on every car made .

Aug 29, 2009 | Mazda Millenia Cars & Trucks

1 Answer

Where is the EGR valve located at in a 1993 Mazda Mx6


on the inlet manifold [usually circular design]
Cheers Rob

Aug 16, 2009 | 1993 Mazda MX-6

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

88 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

78257 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...