Question about 1992 Chevrolet S-10 Blazer

2 Answers

Replace flywheel on 92 chevy blazer fullsize 5.7 the easy way

Posted by on


2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Chevrolet Master
  • 6,982 Answers

There is no "easy way" to do that. There is only one way...Transmission needs to be removed, clutch or converter needs to come off and then the flywheel. I suggest you get a haynes or chiltons to guide you through the procedure (too long to write here). One tip...use guide bolts (two long bolts in a place where you can easily get to them...I saw the heads off and make a screwdriver slot in each) This helps to properly locate the trans while replacing. Also, Never permit the transmission to hang by the input shaft or converter otherwise unsupported.
If you are uncomfortable working with this, have a shop do it for you. Transmissions are heavy and shops use special jacks to support them. I have done this both ways and balancing a transmission on even a really good floor jack is not fun.
good luck, whichever way you decide to go!

Posted on Sep 13, 2009

  • Level 1:

    An expert who has achieved level 1.


    An expert that has over 10 points.


    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 15 Answers

On some chevy motors it is possible to disconnect the tranny from the motor jus enough that you can stick a wrench between the torque convertor an th fly wheel and remove the flywheel that way then slide it out and slide the new one in is not easy but it saves time i have done it that way before

Posted on Dec 03, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer


disconnect the battery and then clean the throttle body. Then hook back up and see if anything changed.

If just a little or not at all then I would replace the Idle air control valve.

Feb 11, 2010 | 1992 Chevrolet S-10 Blazer

2 Answers

How many quarts of motor oil does a 92 chevy s10 blazer hold

4.5 to 5 qts. It depends on how long you let it drain!

Nov 04, 2009 | 1992 Chevrolet S-10 Blazer

2 Answers

Where is a crankshaft located on an 02 Chevy Blazer? And is it easy to install?

the crankshaft itself? the whole engine has to be torn apart

Oct 05, 2009 | 2002 Chevrolet Blazer

2 Answers

Wiring diagram for 92 chevy blazer

My 1992 Chevy blazer s-10 starts and then the door locks automatically starts locking and unlocking...It wont stay running either...

Jun 11, 2009 | 1992 Chevrolet S-10 Blazer

2 Answers

Where is fuel pump relay on 92 chevy blazer tb

driver's side under the hood above the brake master cylinder ....should be 2 relays there... it's the outer one... they are identical and you can swap them temporarily to check that your fuel pump relay is working.

May 26, 2009 | 1993 Chevrolet S-10 Blazer

2 Answers

Program fob

Instructions to program a keyless entry remote for a Chevy Silverado. They also work on 2003, 2004 and 2006 Suburbans.
  1. Close all the vehicle doors.
  2. Insert the ignition key into the ignition lock cylinder.
  3. Press and hold the DOOR unlock switch.
  4. While holding the DOOR lock switch in the unlock position, cycle the ignition ON, OFF, ON, OFF.
  5. Release the DOOR unlock switch. The doors will lock and unlock to confirm the program mode.
  6. Press and hold the LOCK button and the UNLOCK button simultaneously on one keyless remote. After a delay of approximately 15 seconds, the doors will lock and unlock to confirm the programming of that transmitter.
  7. Repeat the previous step to program up to four transmitters.
  8. Turn the ignition switch to the RUN (one more click forward) position in order to exit the keyless entry transmitter mode.
  9. Operate the transmitter functions in order to verify correct system operation

Apr 19, 2009 | 1999 Chevrolet Silverado 1500

1 Answer

None of the lights will work in my 1988 chevy k 1500

Check fuses, then the switch. I have a 94 Chevy 2dr Fullsize Blazer and the switch went out on mine. It started flickering, then gave out.

Mar 21, 2009 | 1983 Chevrolet Silverado

1 Answer

87' blazer grill converted to 89' -Help-!!

try checking for a headlight harness that belongs to the 89 and match it, or look for one online. Conversions can change the harness sometimes. You don't have to cut any wires. If you cut wires, sometimes you will have a bigger problem than you thought.

Jun 10, 2008 | 1988 Chevrolet Blazer

Not finding what you are looking for?
1992 Chevrolet S-10 Blazer Logo

319 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

78919 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides