Question about 1992 Chevrolet S-10 Blazer

Open Question

92 chevy fullsize blazer trying to replace the flywheel do i have to removed or is it a easier way to do it 350 t.b.i

Posted by on

  • Roberta Smith
    Roberta Smith May 11, 2010

    basically you have to remove the transmission. change it then bolt it all back up again

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Chevy 350 flywheel


most starters are the same on chevy 350s should bolt right up, if you have to change torque converter, but most chevy 350 flywheels are universal. that's the good thing about a chevy most everything 350 smallblock bolts right up. hope this helps

Jan 15, 2014 | Cars & Trucks

1 Answer

Removing a starter from a 1991 chevy s-10 blazer 4x4 , 4.3L v6...


The starter is under the vehicle on the passenger side. The best way is to turn your wheels to the left so you can reach the top of the starter solenoid behind the passenger tire. First undo the nuts from the solenoid terminals, second loosen the bolts holding the bell housing for the flywheel and slide it over enough to make room, third undo the starter mounting bolts and the starter should come out easier. And just reverse the steps for installation.

Jan 07, 2011 | 1991 Chevrolet S-10 Blazer

1 Answer

I need to change out a water pump on my 92 full size blazer.


u might be able to just remove alt and fan and maybe not. Only other things that might needed to removed is a/c compresser, power steering pump and fan shroud (((you dont have to remove shroud but makes it alot easier)))

look at water pump and look to see what all in way of getting to all the bolts

Apr 07, 2010 | 1992 Chevrolet S-10 Blazer

1 Answer

Replace water pump


u need a special wrench to remove the fan from old pump the rest is pretty much like old chevy 350

Mar 20, 2010 | 2002 Chevrolet Blazer

2 Answers

Replace flywheel on 92 chevy blazer fullsize 5.7 the easy way


There is no "easy way" to do that. There is only one way...Transmission needs to be removed, clutch or converter needs to come off and then the flywheel. I suggest you get a haynes or chiltons to guide you through the procedure (too long to write here). One tip...use guide bolts (two long bolts in a place where you can easily get to them...I saw the heads off and make a screwdriver slot in each) This helps to properly locate the trans while replacing. Also, Never permit the transmission to hang by the input shaft or converter otherwise unsupported.
If you are uncomfortable working with this, have a shop do it for you. Transmissions are heavy and shops use special jacks to support them. I have done this both ways and balancing a transmission on even a really good floor jack is not fun.
good luck, whichever way you decide to go!

Sep 12, 2009 | 1992 Chevrolet S-10 Blazer

2 Answers

I have a fullsize chevy blazer 350 f.i. takes off slow if im at a light or stop in gear it idels really low like around 200 to 300 rpms


1 Inspect Distributor Cap Loose, Cracked or Worn Distributor Cap. 2 I 1 Inspect EGR Valve Improperly Functioning or Faulty EGR Valve. nspect

1 Inspect Idle Stop Solenoid Damaged, Loose, or Faulty Idle Stop Solenoid
Distributor Cap and Rotor Kit Loose, Cracked or Worn Distributor Cap.

Sep 02, 2009 | 1992 Chevrolet S-10 Blazer

1 Answer

Distributor cap diagram 92 chevy blazer full size 8 cylinder 350 motor


go to autozone and they have a place on their computers there to solve any question like this. they can even print you a copy. Good luck.

Aug 28, 2009 | 1992 Chevrolet C/K 3500

2 Answers

Wiring diagram for 92 chevy blazer


My 1992 Chevy blazer s-10 starts and then the door locks automatically starts locking and unlocking...It wont stay running either...

Jun 11, 2009 | 1992 Chevrolet S-10 Blazer

1 Answer

87' blazer grill converted to 89' -Help-!!


try checking for a headlight harness that belongs to the 89 and match it, or look for one online. Conversions can change the harness sometimes. You don't have to cut any wires. If you cut wires, sometimes you will have a bigger problem than you thought.

Jun 10, 2008 | 1988 Chevrolet Blazer

Not finding what you are looking for?
1992 Chevrolet S-10 Blazer Logo

Related Topics:

55 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...