Question about 1993 Lincoln Continental

1 Answer

Friend called me today and hes been working on this car dont know make or model it has the ford 3.8 liter and had the upper intake off of motor and he thinks the pcv valve may have fell into the intake so he says he could not find the old when going back together with car and just bought new one so the car runs but has slight poppin noise while accelerating so what damage could this do or has it done so far and also can he just pull the upper intake back off and get it out.

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Lincoln Master
  • 14,036 Answers


Posted on Sep 12, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

My friend removed the intake from my 1994 Ford F 150 5 liter but doesn't know how the spark plug wires go back or how to install the distributor properly

look it up on youtube very good videos to follow, takes a lot of texting to do here in this forum. Good Luck, its not that hard of a problem, you will see.

Apr 23, 2015 | Ford F-150 Cars & Trucks

1 Answer

Thermostat housing is leaking i need remove throttle body upper intake manifold for ford explorer Eddie Bauer

If it is a single overhead can 4.6 liter v8 the intake manifold is notorious for leaking on that model of ford engine I just replaced one on a friends explorer the seal on the intake manifold deteriorates causing the leak and replacement of the manifold is the only solution! Good luck!

Jan 04, 2015 | Ford Cars & Trucks

1 Answer

4.0 liter motor will not idle below 24500 rpm. 1994 aerostar, 4 liter motor, auto

i hope that the 24,500 RPM is a miss-print and you mean 2450 RPM.

get a can of carburetor cleaner and spray around the intake manifold with the engine running if there is a vacuum leak causing the idle problem when you spray the cleaner around the leak the idle will change, if you find no leaks replace the idle control valve or motor witch ever you want to call it.

let me know if there is any thing else you need.

Jun 12, 2011 | 1994 Ford Aerostar Extended

1 Answer

2001 E250 4.2L 144K drives fine. rough idle (up/down) at a stop then stalls out. doesnt happen all the time.

The 2001 4.2 liter has some common issues. Normaly you get an engine code P0171 and P0174 for what I'm talking about...
They are know to have dry cracked PCV hoses out of the right valve cover (Passenger side)
Also, the upper intake gaskets and through bolts get dry and hard and leak air. (These have a two piece plastic upper intake)

Dec 13, 2010 | Ford E-250 Cars & Trucks

2 Answers

For 2002 ford sports trac sohc 4.0l. i need the vaccum line diagr

dear friend-if one of the two hoses got a valve on the one end that must go to the booster and the other will go to the crankcase to **** the gasses from the crank case.

Jul 17, 2009 | 2000 Oldsmobile Alero

3 Answers

Whats the best type motor oil/transmission fluid 4 1994 corolla?

car condition good just go for 10w 30 for good density oil

Jul 03, 2009 | 1994 Toyota Corolla

1 Answer

Intake torque specs

Upper intake

Stage 1: Tighten to 20 Nm (14 lb-ft).
Stage 2: Tighten to 25 Nm (18 lb-ft).

Lower intake

Stage 1: Tighten to 15 Nm (11 lb-ft).
Stage 2: Tighten to 32 Nm (24 lb-ft).

Rocker Arms

Stage 1: Tighten to 10 Nm (89 lb-in).
Stage 2: Tighten to 32 Nm (24 lb-ft).

May 17, 2009 | 2000 Ford Windstar

1 Answer

Will a ford c6 tranny bolt on to a 1995 ford 5.0l or 5.8l motor?

From 1990-1996 The C6 was replaced by the E4OD which was modified to include a fourth forward speed and electronic shift controls, replacing the hydraulic control mechanism of the C6.

The C6 works fine in your bronco.. Your friend will need a different transfer case!. i dont have the manual but this is my best guess. FOrd likes to make cars that have interchangeable parts. Like a 1999focus can interchange with 2007. as long as the liter and engine size are the same. In some cases. you will have to use different transfercase.

So you might be better off with a c6 transfer case or c4 for your friend.

Hope this helps

Feb 16, 2009 | 1995 Ford Bronco

1 Answer

1997 Ford Explorer with 4.0 SOHC is flooding out at start

NO you dont have to take the intake off it should be right on the fuel rail with either 1 or 3 bolts if i remember right it will be the only thing on the rail with a vacuum hose on it.

Jan 08, 2009 | 1997 Ford Explorer AWD

1 Answer


there are 3 timing belt in the v6 model. next time make sure to make marking before removing the belts.

Nov 10, 2008 | 2002 Land Rover Freelander

Not finding what you are looking for?
1993 Lincoln Continental Logo

Related Topics:

56 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts


Level 3 Expert

76164 Answers


Level 3 Expert

5522 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides