Question about 1995 Chevrolet K2500

Open Question

I have a 95 chevy k1500 and just bought a 98 k 1500 front clip with composite headlights. the 95 had single sealed beam headlights. my question is.. the wiring harness from the 98 has a rectangle type plug with 6 wires in it and where i need to plug it into the 95 clip on the fire wall has a round plug with 5 wires. any help?

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need to replace the front driver's side headlight assembly on a 1997 mitisubishi galant es. Was wondering if I had to take the bumper off


did you even look first? seems not../.... sigh.....
in the fsm. look
at alldata.com,. look
that is a how to fish story
all answers USA.
composite or sealed beams. HL? they had 2 types.
composite
open hood its in plane site, see them? just look,
seal beams is this.
  1. Raise the headlights using the pop-up switch.
  2. Disconnect the negative battery cable.
  3. Unfasten the retaining screws, then remove the upper and the lower headlight bezels.
  4. Remove the headlight retaining ring screws, and the headlight retaining ring.
  5. Pull the headlight partially out, detach the connector, then remove headlight assembly from the vehicle.

Jul 11, 2014 | Cars & Trucks

1 Answer

Adjust headlights 1995 GMC


Here are directions....
  1. Park the vehicle on a level surface, with the fuel tank about 1 / 2 full and with the vehicle empty of all extra cargo (unless normally carried). The vehicle should be facing a wall which is no less than 6 feet (1.8m) high and 12 feet (3.7m) wide. The front of the vehicle should be about 25 feet from the wall.



0996b43f8022cced.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 5: Location of the aiming screws on most vehicles with sealed beam headlights


0996b43f8022ccee.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 6: Dual headlight adjustment screw locations-one side shown here (other side should be mirror image)


0996b43f8022ccef.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 7: Example of headlight adjustment screw location for composite headlamps

  1. If aiming is to be performed outdoors, it is advisable to wait until dusk in order to properly see the headlight beams on the wall. If done in a garage, darken the area around the wall as much as possible by closing shades or hanging cloth over the windows.
  2. Turn the headlights ON and mark the wall at the center of each light's low beam, then switch on the brights and mark the center of each light's high beam. A short length of masking tape which is visible from the front of the vehicle may be used. Although marking all four positions is advisable, marking one position from each light should be sufficient.



0996b43f8022ccf0.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 8: Low-beam headlight pattern alignment


0996b43f8022ccf1.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 9: High-beam headlight pattern alignment

  1. If neither beam on one side is working, and if another like-sized vehicle is available, park the second one in the exact spot where the vehicle was and mark the beams using the same-side light. Then switch the vehicles so the one to be aimed is back in the original spot. It must be parked no closer to or farther away from the wall than the second vehicle.
  2. Perform any necessary repairs, but make sure the vehicle is not moved, or is returned to the exact spot from which the lights were marked. Turn the headlights ON and adjust the beams to match the marks on the wall.
  3. Have the headlight adjustment checked as soon as possible by a reputable repair shop.

Jan 26, 2014 | 1993 GMC Sierra K1500

1 Answer

Need a wiring diagram for sealed beam to composite headlights on 97 s10


Do not CALL, go directly to your local dealer PARTS DEPARTMENT NOT The Serivice Department and smooze the CSR to grab a print out of the schemata...
Best regards
Ck

Jul 17, 2012 | Cars & Trucks

1 Answer

How to replace headlights on 1989 toyota camry


1989 Toyota Camry

A little personal tip - if you get fingermarks on a halogen headlamp, you can wipe them off with rubbing alcohol (isopropyl alcohol) or, if you want to do what mechanics do, keep a number of 2X2 alcohol wipes in your automotive toolbox just to wipe off halogen headlight bulbs.

HEADLAMP REMOVAL & INSTALLATION

Sealed Beam Headlamps

See Figures 2 and 3

Before making a headlight replacement, make sure that the headlight switch is in the off position.

1. Loosen the screws, release the clips and remove the headlight door. To release the clips, insert a flat blade screwdriver into the jaws of the clip and pry on the jaws.

2. Remove the beam unit retaining ring screws and remove the beam unit.

Fig. 2: Headlamp door clip removal

3. Compress the lock releases and disconnect the wire connector from the headlight. If the connector is tight, wiggle it while holding in the lock releases and pulling out.

Fig. 3: Do not remove the adjusting screws when removing the head lamp sealed bulb

Never try to loosen the aim adjusting screws. If the screws are loosened, the headlights will have to be re-aimed by a qualified technician.

4. When installing, use only a sealed beam unit with the same part number and wattage.

Composite Headlamps

See Figures 4, 5 and 6

Fig. 4: Headlight bulbs are inside the sockets located in the engine compartment

Fig. 5: Detach the wiring from the back of the headlamp bulb

This procedure only applies to replaceable halogen headlight bulbs (such as Nos. 9004 and 9005); it does not pertain to sealed beam units.

1. Open the vehicle's hood and secure it in an upright position.

Fig. 6: Twist and pull the bulb out, but do not touch the bulb if it is still good

2. Unfasten the locking ring which secures the bulb and socket assembly, then withdraw the assembly rearward.

3. If necessary, gently pry the socket's retaining clip over the projection on the bulb (use care not to break the clip.) Pull the bulb from the socket.

To install:

4. Before installing a light bulb into the socket, ensure that all electrical contact surfaces are free of corrosion or dirt.

5. Line up the replacement headlight bulb with the socket. Firmly push the bulb onto the socket until the spring clip latches over the bulb's projection.

WARNING
Do not touch the glass bulb with your fingers. Oil from your fingers can severely shorten the life of the bulb. If necessary, wipe off any dirt or oil from the bulb with rubbing alcohol before completing installation.

6. To ensure that the replacement bulb functions properly, activate the applicable switch to illuminate the bulb which was just replaced. (If this is a combination low and high beam bulb, be sure to check both intensities.) If the replacement light bulb does not illuminate, either it too is faulty or there is a problem in the bulb circuit or switch. Correct if necessary.

7. Position the headlight bulb and secure it with the locking ring.

8. Close the vehicle's hood.

Fig. 1 - various automotive lamps

10_4_2011_8_32_12_pm.jpg

Fig.2 - Headlamp Door Clip Removal

10_4_2011_8_32_40_pm.jpg

Fig. 3: Do not remove the adjusting screws when removing the head lamp sealed bulb


10_4_2011_8_33_24_pm.jpg

Fig. 4: Headlight bulbs are inside the sockets located in the engine compartment


10_4_2011_8_33_51_pm.jpg

Fig. 5: Detach the wiring from the back of the headlamp bulb


10_4_2011_8_34_22_pm.jpg

Fig. 6: Twist and pull the bulb out, but do not touch the bulb if it is still good.

10_4_2011_8_34_49_pm.jpg

Oct 03, 2011 | 1989 Toyota Camry

1 Answer

How I adjust headlights on a 1999 grand am?


  • Determine the type of headlights you have on your car. You can only adjust composite headlights if they bolt to adjuster plates. For dual headlights, look on the headlights for four adjustment screws per side. Sealed beam units have interior adjustment screws under the hood.
  • 4 Locate your adjustment screws. On sealed beam units, you may need to remove the trim screws and pull the trim off to reveal the Torx screws.
  • 5 Begin with you headlights turned on to the low beam. Use a Torx screwdriver for sealed beam units and Phillips screwdrivers for other types of headlights.



  • Dec 09, 2010 | 1999 Pontiac Grand Am GT

    2 Answers

    How to change out the headlights on my 1997 Honda Civic?


    if you have bought the new headlights, then you just need to take out the outer cover of your lights, then remove the old bulbs from the holder and put the new ones.. fix the outer cover back..

    Jul 10, 2009 | 1997 Honda Civic

    1 Answer

    Can't replace 2005 Chevy Aveo headlight


    You do not need to take the headlight assembly out. It is not a sealed beam. There is a ring that locks the light bulb in, found on the back. The drivers side is much easier if you remove the battery. As with all Halogen bulbs, do not touch the bulb with your fingers as it will shorten their life.

    Apr 13, 2009 | Chevrolet Aveo 5 Cars & Trucks

    3 Answers

    Chevy S/10 headlights


    headlights are on a circuit breaker--not a fuse. so if you have a high amp draw situation--the breaker will get hot and turn the lights out then cool off and reconnect(a safety feature so you may have headlights a least part of the time). You need to look for reasons for a high draw. bad headlights themselves are the most popular cause as well as corroded connecters. Hope I helped

    Apr 06, 2009 | 1994 Chevrolet S-10

    2 Answers

    1993 Chevy Silverado truck headlights high beam only works no low


    dimmer switch has gone bad need to change your dimmerswitch

    Apr 01, 2009 | 1993 Chevrolet K1500

    Not finding what you are looking for?
    1995 Chevrolet K2500 Logo

    Related Topics:

    60 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Chevrolet Experts

    yadayada
    yadayada

    Level 3 Expert

    76164 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8273 Answers

    Are you a Chevrolet Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...