Question about 1991 Peugeot 405

Open Question

Peugeot 106 the indicater and light switch isn't

1996 peugeot 106 the indicater and light switch isn't working propely as you indicater right the high beam comes on and if you go left the high beam and the indicater as well, when try to turn lights on nothing happens and it only turns one click (side lights) but no lights come on? i think it's to do with the connection in the arm itself!!!!!!!

Posted by on

  • Anonymous Mar 27, 2014

    Head lights come on when the door is opened and stay on for couple of minutes when the van is exited. have also found that during driving I have no full beam and have no high speed wipers.
    I have had the complete column on the steering wheel replaced which did not rectify the problem

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2010 impala high beams do not come on, light on dash comes on, replaced bulbs still don't work, checked all fuses, look good


High Beam Headlamp Operation
Battery voltage is applied at all times to the coil and switch sides of the HIGH BEAM PCB Relay located in the underhood fuse block. When the headlamp dimmer switch is placed in the high beam position, the headlamp dimmer switch signal circuit to the BCM is pulled low signaling the headlamp high beam request. In response to this signal, the BCM applies ground through the high beam relay control circuit energizing the high beam relay. With the high beam relay energized, battery voltage is applied through the switch side of the relay, the left and right high beam fuses, and the high beam supply voltage circuits illuminating the high beam headlamps. At the same time the BCM sends a GMLAN serial data message to the instrument panel cluster (IPC) requesting the IPC to illuminate the high beam indicator. Ground for the left headlamp is provided at G101 and the right headlamp at G100.

Nov 23, 2016 | 2010 Chevrolet Impala

1 Answer

Left operating headlight not working


the switch supplies power to the relays that switch on the lights according to the position you have it at
so on high beam there will be 2 high beam lights working
on low beam there will be 2 low beam lights working
back to passing lights or flashing head lights , both beams will work so the switch is the last item to consider
Now with only one side beam not working it comes back to the ground on that light for that bulb
remember that electricity follows the path of least resistance so it the ground is bad the current will ground out through another point including a light which will switch that light off or make it not work
remember the brakes light that flask when an indicator is used --same thing

Jan 24, 2016 | 2000 Nissan Maxima

1 Answer

Only one head light works at a time, diferent light in all positions


Most likely the high beam filament is burnt out on your left light, and the low beam filament is burnt out on your right light. My first recommendation would be to purchase a couple of headlamp bulbs, install them and see how they work, then post back if you are still having an issue

Aug 23, 2014 | 2002 Dodge Grand Caravan

1 Answer

1996 honda civic headlights


I'm guessing you mean high beam on left side not working. All headlamps are on separate fuses for safety reasons so check the LH high beam fuse then check the bulb holder for corrosion or dirty contact with bulb. It won't be the dimmer switch as the wire from the switch goes to a relay which operates both lights

Aug 22, 2014 | Cars & Trucks

1 Answer

Low beam light does not work but high beam does. not bulb or multi switch or cramped wire any idea?


Check the fuse box . Some vehicles have a fuse for the high beam and the low beam. Usually a 10 amp spade type fuse. Some vehicles use a separate fuse for right and left sides.

Jan 17, 2010 | 1996 Ford Explorer

1 Answer

Battery Light Stays on on my peugeot 106


check the fuses by the battery ,the big ones,then the other fuses ,if this fails then don mini and heels and drive to garage

Feb 13, 2009 | 1987 Peugeot Liberte

2 Answers

1996 ford ranger headlights not working


It's the dimmer switch in the column.

Jan 06, 2009 | 1996 Ford Ranger SuperCab

1 Answer

My bright light indicater is working, but I don't have any bright lights?


So, when u turn on the high-beams, the indicator light goes on, but u still have low beam headlights only? Check the headlight (either one), and see if by chance both high beams burned out at approx. the same time. U don't specify what year, I'm not sure if u have a replacement bulb, or a sealed beam headlight to replace. If the high beams are both ok, then it must be the headlight high beam switch. Let me know what u find.

Nov 05, 2008 | Honda Accord Cars & Trucks

3 Answers

Brake lights on peugout 106


check the plug-in on the brake switch. also that switch is adjustable, maybe you can adjust it.

Jun 21, 2008 | 2005 Peugeot 405

Not finding what you are looking for?
1991 Peugeot 405 Logo

Related Topics:

180 people viewed this question

Ask a Question

Usually answered in minutes!

Top Peugeot Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Wahs Team

Level 2 Expert

205 Answers

yadayada
yadayada

Level 3 Expert

74896 Answers

Are you a Peugeot Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...