Question about 2006 Ford Laser

Open Question

I have b6 non turbo wiring loom is the same as

I have b6 non turbo wiring loom is it the same as aford sohc general 1point6 motor

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Chrysler Sebring 2001 3.0 v 6 sohc interference motor or non interference I've seen answers that it was and then it wasn't


Chrysler
  • 1.4L, 1.5L & 1.6L Interference
  • 1.7L Non-Interference
  • 1.8L Interference
  • 2.0L DOHC Interference
  • 2.0L SOHC Interference
  • 2.2L DOHC Interference
  • 2.2L SOHC Non-Interference
  • 2.22L SOHC Interference
  • 2.3L Diesel Interference
  • 2.4L DOHC Non-Interference (Valves may hit if camshafts turn out of time)
  • 2.4L SOHC Interference
  • 2.5L 4 Cyl. Non-Interference
  • 2.5L V6 Interference
  • 3.0L SOHC 12 Valve Engine Non-Interference
  • 3.0L DOHC Interference
  • 3.0L SOHC 24 Valve Engine Interference
  • 3.2L Interference
  • 3.5L Interference
  • 4.0L Interference
  • this should be what your looking for.

Dec 10, 2015 | Chrysler Cars & Trucks

1 Answer

Where do i get wiring loom for mazda rustle B6 my auto says thats what i need


Painless wiring system may be easier to acquire.
google "painless wire harnes", hope it helps!

Jan 18, 2014 | Cars & Trucks

1 Answer

1994 Dodge Stealth RT, V6 DOHC non turbo, overheating.......car bible shows thermostat in bottom radiator housing........parts store only shows a gasket for the top radiator hose housing, which the book...


in most vehicles it is in the housing where the top radiator goes onto the engine, but in some vehicles it is at the bottom ( especially subaru vehicles)......cheers.

Sep 20, 2011 | 1994 Dodge Stealth

1 Answer

I have a 92 legacy sedan with bad motor. Bought a 92 legacy wagon turbo. Do I have to change wire harness in front with computor, or can I change just computor?


hi im presuming your old car is non turbo if so you will have to change a lot of parts over to make it work, you will have to replace entire engine loom, the ecu will need changed over then the fuel pump and all of the fuel lines will need to be replaced with the bigger turbo model ones to keep up also the trans will bolt strait up but will be the major weak point so swap over if possible.

Jun 15, 2011 | 1992 Subaru Legacy

1 Answer

What is the torque setting for the crankshaft bolt on a 1997 Mazda B6 8valve carburettor engine and also for th water pump bolts?


What motor....L 4-218cc 2.2L 2200 2-bbl
L4-218cc 2.2L 2200 MFI or L4-2606cc 2.6L SOHC ?????

Jun 04, 2011 | 1991 Mazda B-Series

1 Answer

I have 2 questions... 1) I have a 1986 nissan 300zx how dose one know if its turbo or non-turbo?...on my engine the plate says V6 3000... 2) How the heck do you get to the spark plugs?..iv tryed to get...


if its a turbo you should see something like this, this is an example only the thing on the right with the silver snail type thing is the turbo, you should have 2 of these if its the turbo c993b18.jpg


how to change the plugs--First start by removing the negative battery cable from the battery post. Ok next remove the center plastic cover on top of the motor that says "3000 v6". Now in between each gap in the in intake plenum u should notice the tops of what are called coil packs. Each one has two bolts holding it in and a wire loom coming out of each pack. The first pack is directly left of the oil cap(if facing motor). Remove each bolt then the wire connection. After that gently pull until the pack comes out. Take your spark plug socked and remove plug. Be really carefull not to drop debres in the hole. Repeat this step for the first two on the left side and the first one on the right side (again facing motor). A couple of them you will notice has a small metal plate with a #8 screw holding the wire down, remove this to keep from damaging your wires. Now this is where it gets hard U will have to remove the balance tube on the back of the intake plenum. Calm down its not really that bad, just time consuming. Remove all vacum tubes and hoses from the balance tube and then remove the 1 nut and 2 bolts holding each side down. After that carry on and remove the packs as normal, hope this helps you...good luck

Oct 10, 2010 | 1986 Nissan 300ZX

1 Answer

How do i obtain original computer # for 1992 dodge stealth sohc


if you have a SOHC engine 92 stealth from California the number will be ;MD153355
SOHC Federal emission ECU number will be ;MD153354 .
DOHC , AWD , Turbo Cali emissions ; MD159965
DOHC , AWD ,Turbo federal emmissions ;MD159966
DOHC non-turbo Calif ;MD159962
DOHC non-turbo fed. ; MD159963

Sep 29, 2010 | 1992 Dodge Stealth

1 Answer

Peugeot expert 1.9 diesel van 2005 non turbo/ engine wiring fault


If the engine management light is on you should get it plugged in to a diagnostic tool.Also check the wiring with an ohm meter .

Mar 03, 2010 | 2005 Peugeot 405

2 Answers

What kind of motor is in a 1986 nissan 300zx non turbo is it an interface or not?


Hello adeg222: My name is Roger and I will help you. The motor should be a 3.0 SOHC V-6 engine. The repair manual does not refer to this engine as being a interference engine. How ever if the belt breaks and you were driving the car. The likely hood of engine damage is greatly multiplied.Also the time called for to replace the belt is 8.5 hours.
Should you need further help please just ask. Please rate the quality of the answer. This way I know if it was helpful. Thank You for using Fix Ya. Roger

Dec 12, 2009 | 1986 Nissan 300ZX

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...