Question about 2006 Nissan Maxima

1 Answer

Install headlight bulb on 2006 maxima - 2006 Nissan Maxima

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 986 Answers

Its located by the light behind grab the plug and twist Counter-clockwise remove the plug and bulb by pressing the tabs
Change bulb replace.

Posted on Sep 11, 2009

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

jgwhomeequip
  • 1902 Answers

SOURCE: replacing headlight bulbs on a 2006 chrysler sebring

Behind the headlight you should see a eletrical wires running to the headlight section. There will be a 2 inch round plastic ring. You grap the back of the bulb and turn it to the right which will release the bulb and the socket. You pull out the bulb and replace it the same way. If this doesnt help then get back to me.

Posted on Feb 06, 2009

bunnydawg
  • 5158 Answers

SOURCE: installing headlight bulb in a 2006 Audi A4 Avant

that's generally the only way to change them... you may have to remove the battery or other obstacles to get at them.... a quarter turn or so should free the bulb. careful not to touch the bulb with your fingers as that shortens the life of them

Robert

Please take a moment to rate this solution.. thanks

Posted on Feb 01, 2009

Mustgo
  • 2359 Answers

SOURCE: 2002 Maxima. Left headlight out

2002 has daytime running light,

There are resistance checking circuit that sense stock resistance on the bulb.

9005 is the normal STOCK bulb.

Do put fancy one that claim to be MOVE POWERFUL!


Type the one from the passenger side and see does it lite up.




Posted on Jul 16, 2009

  • 1986 Answers

SOURCE: headlight adjustment

The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Posted on Sep 30, 2009

  • 1 Answer

SOURCE: How do I remove a headlight bulb on a 2006 Lincoln

remove 2 10mm bolts attaching top of headlight to the radiator support.

remove plastic clip attachinig headlight to top/front of fender.

remove 5 phillips screws on top of grill.

carefully pull out grill enough to remove 1 10mm bolt attaching headlight to radiator support and use slotted screwdriver or prybar to seperate headlight tab from the bracket that goes under the bumper cover.

with a little effort and wiggling pull out headlight assembly.

Posted on Apr 17, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2006 nissan maxima SL. My two headlights are damaged. I have the factory Xenon headlights. can regular halogen headlights replace the ones i have in now? Is it just plug and play?


You can by pass it, but regular bulbs are not plug and play. You also won't find plugs that fit the housing for the lights. Different set ups.

Jun 18, 2016 | 2006 Nissan Maxima SL

1 Answer

I have a 2000 maxima...when headlights are on, passenger side blinker stays lit on the dash and doesn't flash at all. While the headlights are off and i turn the passenger turn signal on it then b


Plain and simple...Your turn signal circuit is shorted to your headlamp circuit. What USUALLY causes this is an incorrect light bulb has been installed in the vehicle or the light bulb was installed incorrectly. There are other possible causes of these circuits being shorted together, but 99 out of 100 of the times that I have seen this it is either because somebody just replaced a bulb or a bulb socket melted somwhere on the car. Be sure to check both the front AND rear bulbs.

Jan 07, 2012 | 2000 Nissan Maxima

1 Answer

Headlight BULB, Driver Side, Can I go thru the fender well to change it out? Or do I have to drop the bumper on driver side?


remove wheel,unfasten front half of inner fender liner,pull liner back and you will have access to change bulb.

Feb 06, 2011 | 2006 Nissan Maxima

1 Answer

Replacing headlight bulb on 2006 maxima


Hello,

Replacing Your headlight bulb seem to be easy when You look at it, but quite technical. But If You get the proper guide, I think fixing this will not be difficult for You. You will be needing these instruments to fix this(Flathead screwdriver, Phillips head screwdriver, 3/8 inch drive ratchet, 3/8 inch drive 10 mm socket, Replacement bulb(s), Shop rags or towel), then You carefully follow the steps below to fix this:
  1. Turn the steering wheel all the way in toward the engine on the side you are changing the light bulb in. For the driver's side bulb replacement, turn the steering wheel all the way to the right. For the passenger side bulb replacement, turn the steering wheel all the way to the left.
  2. Turn the ignition switch to the off position and remove the keys. Make sure the light switch is in the off position.
  3. Remove the retaining clips and screws from the front of the wheel well area, including the bottom splash shield valance underneath the front of the Maxima. The valance is attached to the wheel well and can be left intact. Use the Phillips head screwdriver for the screws and the flathead screwdriver to pop up the center post of the clips and then pry the clips out. Remove enough of the clips to gain access into the front fender cavity.
  4. Locate and turn the outer low-beam headlight cover counterclockwise to remove it. This will reveal the bulb and socket.
  5. Turn the bulb counterclockwise to remove it from the headlight assembly.
  6. Release the retaining pin (if applicable for theft deterrent package).
  7. Remove the wire harness plug from the bulb socket and then remove the bulb.
  8. Insert the new bulb into the socket without touching the glass of the bulb. Reverse the procedure to reinstall.
But if it is the high beams bulb You want to replace, then please follow the steps below, It is the same instruments as before You will be needing to do this job.
  1. Release the hood latch if you're replacing the high beam bulb only. Then lift the hood. Locate the two 10 millimeter bolts at the top of the headlight assembly and remove them with the ratchet and the socket.
  2. Locate the four fascia retaining pins and remove them using the flathead screwdriver. This will allow flexible movement of the fascia to remove the headlight assembly.
  3. Place a shop rag or towel between the tight gap of the fascia and the bottom of the headlight assembly to prevent scratching the fascia.
  4. Maneuver the headlight assembly forward away from the front of the Maxima. There is a guide pin still retaining the assembly in place so apply equal parts of determination and gentleness to remove the assembly without scratching the lens or the fascia.
  5. Remove the headlight assembly far enough to get your hand behind it and remove the seal from the back of the high-beam headlight. Turn the seal counterclockwise to remove.
  6. Turn the bulb counterclockwise to remove from the assembly.
  7. Release the retaining pin (if applicable).
  8. Unplug the wire harness from the light bulb and remove the light bulb.
  9. Plug the new replacement bulb into the wire harness without touching the glass of the bulb.
  10. Reinstall by reversing the procedure.
Hope this information helped. Thank You for using FixYa!!!

Jan 15, 2011 | 2006 Nissan Maxima

1 Answer

Need to replace the headlight bulb (drivers side) in my 1999 nissan maxima. what are the steps?


using a flashlight or drop cord, look under left front fender or under hood, for a pull out receptacle which will be dirty, dusty, turn the unit left or right to remove from the headlight socket, remove bulb unit, install new bulb and reinstall the reverse of removal...

Aug 07, 2010 | 1999 Nissan Maxima

1 Answer

1992 nissan maxima se. my right headlight doesn't


check all fuses , they sometimes pop fuse when bulb blows.good luck.

Oct 26, 2009 | 1992 Nissan Maxima

1 Answer

2006 maxima no power to headlight


check fuses there is a left and right headlight fuse.

Oct 10, 2009 | 2006 Nissan Maxima

1 Answer

Headlight adjustment


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

May 08, 2009 | 2006 Nissan Maxima

1 Answer

Headlight installation instruction


normally raise hood look behind the light that outt is some has a socket you can turn to left or right and the bulb will come turn bulb right or left replace new bulb then replace socket back into head light

Feb 08, 2009 | 2001 Nissan Maxima

Not finding what you are looking for?
2006 Nissan Maxima Logo

551 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

713 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...