Question about 1990 Mitsubishi Galant

Open Question

Removing the front panel in a 1990 Mitsubishi, Galant DOHC .

How do you remove the front panel
to replace blower selector switch which resides directly behind the panel?

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I am trying to find the location for my crankshaft position sensor on my 1999 Mitsubishi Diamante


Your 1999 Mitsubishi Diamante is a 3.5L MFI SOHC 6cyl engine.
MFI = multi-port fuel injection
SOHC = single overhead camshaft
This answer covers Mitsubishi Diamante1.8L, 2.4L, 3.0L (SOHC and DOHC), 3.5L, and 1997-2000 1.5L Engines.

2.4L engine shown, others similar.

Fig.1 - CKP position and its two mounting bolts
am-trying-find-location-crankshaft-vkz3iz4htmqkl2kxsk34hqrj-3-0.jpg

In Fig. 1, the two arrows point to the CKP (crankshaft position sensor) mounting bolts to remove. 2.4L engine shown.

Fig.2 - CKP reluctor removal
am-trying-find-location-crankshaft-vkz3iz4htmqkl2kxsk34hqrj-3-2.jpg
Remove the sensor and slide the reluctor wheel off of the crankshaft-2.4L engine shown.

1. Disconnect the negative battery cable.
2. Remove the timing belt.
3. Unplug the sensor connector.
4. Unfasten the two retaining bolts, then remove the CKP sensor from the vehicle.
5. Installation is the reverse of the removal procedure.

Reference: Autozone online repair guide: Mitsubishi Galant/Mirage/Diamante 1990-2000, at
www.autozone.com

Fig.3 - photo - new 99Diamante CKP, a Wells part #SU4313
am-trying-find-location-crankshaft-vkz3iz4htmqkl2kxsk34hqrj-3-5.jpg

Jul 31, 2016 | 1999 Mitsubishi Diamante

1 Answer

Whats the firing order for a mitsubishi galant 1990


Hi there:
Check this on 1990 Mitsubishi Galant 2.0 liter SOHC L4...
8_24_2012_3_50_07_pm.gif

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Aug 24, 2012 | 1990 Mitsubishi Galant

1 Answer

I have a 99 mitsubishi galant need to replace expansion valve. do i need to remove complete dash panel.


no, the a/c box is in 3 parts. you will need to remove the glove box, then remove the section just left of the blower motor. this is where the a/c evaporator is located and the expansion valve is on the side of the it.

Jul 28, 2011 | 2001 Mitsubishi Galant

1 Answer

How do i replace a blower motor


I assume the blower is not running. The first thing to check is the fuse for the blower motor. This is either in the fuse panel under the dash or on the main junction box in the engine bay.

Next step is to check that the motor is actually getting power. You should be able to access the blower fan assembly from the glove compartment. The compartment door will probably need to be removed, along with some other dash parts. You should be able to see the AC evaporator unit, with the fan assmbly.


It's unlikely but not impossible that the motor has failed. There may be leaves or other garbage in the motor assembly. In any case, removing the assembly will allow you to clean and test it.

The more likely problem however is the blower speed 10W resistor has failed. Look on the assmbly for a removable panel with two or three wires. Remove this panel, and look for a large ceramic resistor. This sits in the air flow to keep cool, and adjusts the blower speed.

When this resistor burns out, the blower stops.

Jan 09, 2011 | 2003 Mitsubishi Galant

1 Answer

No heat or cold air will come out of my2004 Mitsubishi Galant. I took off the dash panel behind the glove box to get to the Blend Door Motor, but after turning the air from hot to cold at various speeds,...


Does the air blows through the dash board vents. Does the selector is functional, that means you can force the air stream through wind shield, or vents or down to the legs. If these things are OKthen check CONTROL PANEL.
Remove the trim plate surrounding the center instrument panel. Detach the electrical connectors and remove the control panel.

Read more: How to Troubleshoot the Air Conditioning in a Mitsubishi Galant | eHow.com http://www.ehow.com/how_4520422_troubleshoot-air-conditioning-mitsubishi-galant.html#ixzz0yf04FfuE

Sep 05, 2010 | 2004 Mitsubishi Galant

1 Answer

How to remove the intake manifold to replace rear spark plugs for a 2001 galant mitsubishi v6


you shouldnt have to remove the manifold. you can access those plugs by removing the front tire and go in that way.

May 04, 2010 | 2001 Mitsubishi Galant

1 Answer

Window wont go up but will go down


Possibly a bad relay for one of the motors

May 21, 2009 | 1990 Mitsubishi Galant

1 Answer

I have a 2000 ford E350 van with front and rear air. the front blower motor runs at low speed, The front blower still runs on low even when the knob is set on medium or high. I do not know where the...


it's either the blower motor switch or blower motor resister. Resistor ?Heater Blower Motor Switch Removal Remove the battery (10655) ; refer to Section 414-01 . Remove the battery tray. Remove the screws. Remove the battery tray. Disconnect the heater blower motor switch resistor connector. Remove the heater blower motor switch resistor (18591). Remove the two screws. Remove the heater blower motor switch resistor. ----------------------------------- Switches Removal Disconnect the battery ground cable. Remove the center trim panel; refer to Section 501-12 . Remove the control assembly. Remove the screws. Remove the control assembly. Remove the A/C-heater function selector switch knob. Disconnect the vacuum harness connector. Disconnect the A/C-heater function selector switch connector. Remove the A/C-heater function selector switch. Remove the screw. Remove the A/C-heater function selector switch. Remove the temperature control switch knob. Disconnect the temperature control switch connector. Remove the temperature control switch. Remove the screw. Remove the temperature control switch. Remove the heater blower motor switch knob. Disconnect the heater blower motor switch connector. Remove the heater blower motor switch (18578). Remove the screw. Remove the heater blower motor switch. ----------------------------

Mar 31, 2009 | 2007 Ford E-350 Super Duty Length XLT

2 Answers

Mitsubishi Galant 1992


1992 Mitsubishi Galant
2.0 liter DOHC L492789848.gif

Aug 18, 2008 | 1992 Mitsubishi Galant

Not finding what you are looking for?
1990 Mitsubishi Galant Logo

Related Topics:

49 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8215 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...