Question about 2002 Kia Rio

1 Answer

What kind of cv axle tool do i need to remove the cv axles on the front of the car on a 2002 kia rio. I called and asked a parts place they said there is quiet a few and im not sure which one that i need.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 986 Answers

You will need a pry bar it will snap out with a little force,I hope this helps you and thank you

Posted on Sep 11, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Are there any specialty tools required for replacing the CV axles on a 2005 kia optima?


Not an easy job if you are planning to do at home. A good socket set will help in removing most bolts. You will need the proper axle nut socket to remove the axle nut. This can be a very tedious procedure without the use of air tools. The CV axle may require a special removal tool that slips in behind the inner joint to seperate it from the transmission as these can be diffucult to remove.

Aug 23, 2015 | Kia Cars & Trucks

1 Answer

How to remove left front axle from 2007 kia sorento? the axle not the cv axle.


Hi there, one end will knock off and the othe may have a circlip holding it on, you will need to clean all grease of to find it properly, hope this helps.

Feb 14, 2015 | 2007 Kia Sorento 4x4

1 Answer

How do I replace my inner axle on the passenger side of my 2002 Dodge Ram 4x4 4.7L. I lent my truck out and the C clip let go of the CV axle. The intermediate axle spline is stripped and I need to change...


Lift and support front end on suitable jack stands preferably on frame. Remove right front cv axle, stub shaft, and seal. You will need to pull the right front brake caliper assembly loose and place to the side. Then remove bolts from shock and upper control arm and hub nut to do this. Next, remove axle lock actuator on passenger side of front axle. Place a drain pan underneath front diff cover and remove cover and drain axle. In the center of differential there will be an 8 mm head bolt holding spider gear cross-shaft. Remove bolt and cross-shaft only! Push inner axle in until clip clears inside of passenger spider gear. Set clip aside and push/pull axle shaft straight out to passenger side.

Feb 09, 2015 | Dodge Cars & Trucks

1 Answer

My driver side cv axle on my 2002 kia spectra won't lock in place ive tried everything .


Pull the axle ,and inspect the lock clip ,replacement of it ,maybe needed

Oct 30, 2014 | 2002 Kia Spectra

1 Answer

Front diff


Here might be the answer for that.
Cv Axle Answers com

May 15, 2014 | Kia Sorento Cars & Trucks

1 Answer

What tools are needed to chang rear cv joint in a 2002 mercury mountaineer


Basic tools..remove wheel, remove axle nut, remove brake caliper, remove lower control arm bolts,remove the bolt for upper control arm, remove the outer tie rod bolt, support vehicle and suspension, the hardest part is getting the axle out of the rear diff, sometimes a simple pry bar will pop it out, but I've run into a lot where you either need the special pickle fork or even have to remove the complete rear diff with axle still attached, remove cover and take out c clip.if you continue prying and hammering between inner cv joint and diff, you will cause damage to diff.the cv joint is steel, cast maybe, and diff is aluminum so guess what will be damaged first? That'll lead into a pretty expensive repair.the special tool to remove axle is 205-529

Mar 01, 2014 | Cars & Trucks

1 Answer

What kind of tool do i need to take off a cv joint?


Welcome to FIxYa.com



Regular tools Metric sockets, pry bar, axle nut socket, ball joint separator, tie rod separator, and know how.



Thank you for using FixYa.com

Regards, Lee Davidian

Dec 21, 2010 | 2003 Kia Rio

1 Answer

Cv axle burst. how can i fix it


you have to replace the cv joint or the whole shaft

Jul 23, 2010 | 2002 Kia Rio

1 Answer

How to change front wheel bearings on 2000 olds intrigue I have a bad left front wheel bearing. Also I have changed the rear ones. Should I go ahead and change the other side?


Yes you can try replace it

What you need to do is go to an auto parts store such as AutoZone. Then buy the Wheel Bearing/Hub Assembly-Front it runs around $150. Once you have the part you need to take off the Caliper and rotor.
Then you need a 36 mm socket to take off the cv nut. You will need a breaker bar if you don't have a tourque wrench, but remove the nut. Then take a hammer and punch, and place the punch on the cv axle and try to knock it through the hub, pushing the cv axle into the boot a little.
Do not pull the hub off before loosening it from the cv axle, that could cause you to have to replace the axle boot. Once you got the cv axle free take the 3 bolts off the back of the hub. If you can't get to the 3 bolts behind the hub you can take the 2 bolts out of the top of the strut and that will give you more room. I was able to keep the strut bolts in.
Once the bolts are out it may be hard to remove the hub. I had to use a lot of WD 40 and a brass hammer to get it off. However, most auto parts stores will rent you a tool that will help you take it off, the same tool will also help with getting the hub free from the cv axle if the hammer and punch did not work. Once removed put the new one on. Makes sure you put some lithium grease on everything before installation.

Mar 17, 2010 | 2000 Oldsmobile Intrigue

Not finding what you are looking for?
2002 Kia Rio Logo

Related Topics:

344 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

yadayada
yadayada

Level 3 Expert

75797 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...