Question about 1994 Toyota Camry

1 Answer

Blinker lever broken on a 94 toyota camry want to fix it

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 4,044 Answers

You will need to open the steering column so you can remove the old module and replace it with a new on. Typically there are 4 screws to be removed to open the column then 2 to remove the switch and install the new switch.

Posted on Sep 11, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

94 Toyota Camry transmission wont go in reverse


Broken band in trans clutch pack, burnt.if it's auto.

Apr 11, 2014 | 1994 Toyota Camry

1 Answer

Have a 94 toyota camry , check engine light comes on when stop at light or car sits at idle. got codes 12 , 22, am very confused !!


Code 12. RPM signal.
Problem area: Loose connection, broken rpm signal wire from distributor to ecm to rpm meter, rpm meter, distributor assembly or ecm defective.
Code 22. Water temperature signal.
Problem area: Loose connection at water temperature sensor connector, broken wire between the sensor and the ecm, defective sensor or ecm.

Aug 25, 2013 | 1994 Toyota Camry

2 Answers

Turn signal makes zzzzzzzzzzztttt sound and won't blink if turned all the way,I have to hold the lever halfway to get the blinker working. Is it the relay switch or the switch itself? Pls. help!


Sounds like the blinker unit is not fuctioning properly. It should be up under the dash, a little tin can. It is easy to fit a new one.

Sep 13, 2011 | 1998 Toyota Camry

1 Answer

94 toyota camrey intermittant can't move lever out of park. Have foot on break.


the gear shift lever is broke if you take the little button thats on shift pad not the one on shifter use something to push down on plastic piece will get you out of park.

Oct 03, 2010 | 1994 Toyota Camry

1 Answer

1994 toyota camry blinkers flashing wen opening and closing the car doors the blinkers on both sides go off for about one minutes then stops simulating an alarm (the car previosly had an alarm but doesnt...


easiest repair is to remove pigtail connected between ign switcg and alarm dicard and plug factort harness back into ign switch hope this helps please rate

May 07, 2010 | 1994 Toyota Camry

1 Answer

1999 toyota camry blinker problem


get the back working it will no longer fast blink change bulb and check with metre see are you getting power to it also check grounds

Mar 27, 2010 | 1999 Toyota Camry

1 Answer

'94 Camry windshied defroster gets no air flow. When switch is moved,it doesn't change airflow-always comes out ot the ducts facing the passenger area(top ducts)only.


The problem concerning the no air flow out the defrost duct on my mom's 94 Toyota Camry is that the rod link from the electric actuator to the vent / defrost flap became disconnected way up under the center left side under the dash. I had to remove the lower air duct from under the steering column for access to use a 1 inch hole saw to make an access hole on the upper side of the case tube opening to see where the rod came off the lever. I went to the local Toyota dealer to try to buy a retainer clip but the part guy told me that it was only sold as a complete housing piece which was very expensive and involved removing a big portion of the dash pad assembly to replace the housing.
At this point , I plan on reconnecting the rod to the lever by simply installing a special washer style retainer on to the end of the rod to keep it connected. You might find a retainer like this one in a carberator repair kit.

Feb 06, 2010 | 2008 Toyota Camry

1 Answer

The blinkers do not turn off automatically. Is


Inside the steering column, there will be a plastic like knob. This knob should be located right by the signal lever. It sounds like this knob has broken or worn down so that it doesn't snag the lever to cause it to turn off again. On some vehicles, the knob will be inside the lever assembly and this would mean that the entire signal arm will need to be changed. The arm should only be held in by 3 or 4 screws.

Oct 13, 2009 | 2004 Toyota Sequoia

2 Answers

Fast Blinker


hi usurally when that happens that means you have a bad bulb or bad wiring.

Feb 05, 2009 | 1999 Toyota Camry

4 Answers

Fuel Door will not open


the cable from the lever to the door has broken. If you look inside the trunk, (sometimes you will have to pull the carpeted side down) right behind the gas door, you will find a short emergency release cable with a loop on the end - grab and pull the loop and your gas door should pop open.

Jan 12, 2009 | 1998 Toyota Camry

Not finding what you are looking for?
1994 Toyota Camry Logo

Related Topics:

94 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...