Question about 1994 Oldsmobile Cutlass Ciera

1 Answer

94 ciera 3.1 new fuel pump,strainer,filter9/9/09,new crank sensor,new cam sensor7/10/09 new IAC, maf 6/29/09 after disconnecting batt. for 1hr,starts,idles 30 sec. dies now what?

Posted by on

  • mrgonads420 Sep 11, 2009

    replaced a pile of vac hoses then used propane tank for old fashioned leak detector(on one of the few cases it ran)not vac leak every time I have replaced something,it has run for a week,then I have to walk

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 574 Answers

May have a vacuum leak somewhere these are sometimes hard to find. Start at the throttle body should be a couple lines there look for holes,cracks in the lines at throttle body and continue down the lines.

Posted on Sep 11, 2009

  • roberta3fan Sep 11, 2009

    check the choke if its open too wide

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2000 Mercury Mountaineer 5.0L dumping gas into intake manifold and detonation in exhaust manifold on exhaust firing cycle


Fuel pressure regulator bad. Vacuum operated , pull the vacuum line. Smells like fuel. It's bad .Electronic could a fuel pressure sensor on the fuel rail or the fuel pump control module.

Jul 28, 2015 | Mercury Cars & Trucks

1 Answer

Buick 3.8 Fuel Pump 20 A fuse gets no power, no start condition.


hi, I use to have the same problem I had to change engine electrical wires, then I had to change the crank sensor and the module ( destributer ) first let him check the complete wires installation then if they are good let him change the crank sensor

May 28, 2014 | 1993 Buick Regal

1 Answer

2007 NISSAN QUEST It starts and then dies within 2-3 seconds.


hello good day, reverse your air filter, make the bottom to top,, if is not work change the high tension wires

Mar 07, 2013 | 2007 Nissan Quest 3.5 Minivan

1 Answer

2007 NISSAN QUEST It starts and then dies within 2-3 seconds.


It's might be immobilized try the spare key or get it code read that should point u in the right direction

Aug 10, 2017 | 2007 Nissan Quest 3.5 Minivan

1 Answer

91 cutlas ciera 3.3l v6 backfires then stalls but starts back up


SOUNDS LIKE THE IGNITION MODULE OR COIL PACKS HEATING UP

Sep 12, 2012 | 1991 Oldsmobile Cutlass Ciera

1 Answer

98 ford explorer cranks wont fire


Check your Cam,MAP,MAF sensors.

Mar 07, 2012 | 1998 Ford Explorer

1 Answer

How do I change a fuel pump on a 2002 yukon


Need to know the size of the engine but this is a picture of what it is....


Posting the rest of the directions for you:


1cf4b2b.gif
Illustrating fuel pump and sending unit sensor (3) on 2000-2004 4.8L, 5.3L, 6.0L Engines

Removal & Installation
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    • Negative battery cable
  3. Relieve the fuel system pressure.
  4. Drain the fuel tank.
  5. Remove or disconnect the following:
    • Fuel tank

    WARNING Do not handle the fuel sender assembly by the fuel pipes. The amount of leverage generated by handling the fuel pipes could damage tool Joints.

  6. Disconnect the fuel and evaporative emission (EVAP) lines from the fuel tank module.
  • Fuel sender assembly retaining ring using a fuel tank sending unit wrench. Remove the fuel sender assembly and the seal. Discard the seal.
  • Note the position of the fuel strainer on the fuel sender. Support the fuel sender assembly with one hand and grasp the strainer with the other hand. Pull the strainer off the fuel sender. Discard the strainer after inspection. Inspect the strainer. Replace a contaminated strainer and clean the fuel tank.
  • Fuel pump electrical connector
  • Electrical connector retaining clip from the fuel level sensor
  • Sensor electrical connector from under the fuel sender cover
  • Fuel level sensor retaining clip
  • Squeeze the locking tangs and remove the fuel level sensor.
  • Remove the fuel pressure sensor.
  • To install:
    1. Install or connect the following:
      • Fuel pressure sensor
      • Fuel level sensor
      • Sensor retaining clip
      • Electrical connector to the fuel level sensor
      • Electrical connector retaining clip to the fuel level sensor
      • Fuel pump electrical connector

      NOTE Always install a new fuel strainer when replacing the fuel tank fuel pump module.

      • New fuel strainer in the same position as noted during disassembly. Push the strainer on the bottom of the fuel sender until the strainer is fully seated.
      • New seal on the fuel tank

      NOTE The fuel pump strainer must be in a horizontal position when the fuel sender is installed in the tank. When installing the fuel sender assembly, assure that the fuel pump strainer does not block full travel of the float arm.

      • Fuel sender assembly into the fuel tank
      • Fuel sender assembly retaining ring
      • Fuel tank. Install the fuel tank strap attaching bolts. Tighten the bolts to 30 ft. lbs. (40 Nm).
    2. Refill the fuel tank. Install the fuel filler cap. Connect the negative battery cable.
    3. Turn the ignition ON for 2 seconds.
    4. Turn the ignition OFF for 10 seconds.
    5. Turn the ignition ON.
    6. Inspect for fuel leaks.

    Sep 13, 2010 | 2002 GMC Yukon Denali

    1 Answer

    Replace fuel pump for 2002 gmc sierra 2500


    First...this is where the pump is (gas tank) on the engines listed:

    6f9f9d7.gif

    Illustrating fuel pump and sending unit sensor (3) on 1999-2005 4.8L, 5.3L, 6.0L Engines


    Removal & Installation
    1. Before servicing the vehicle, refer to the Precautions section.
    2. Remove or disconnect the following:
      • Negative battery cable
    3. Relieve the fuel system pressure.
    4. Drain the fuel tank.
    5. Remove or disconnect the following:
      • Fuel tank
    8e4564e.gif
    WARNING Do not handle the fuel sender assembly by the fuel pipes. The amount of leverage generated by handling the fuel pipes could damage the joints.

    • Fuel sender assembly retaining ring using a fuel tank sending unit wrench. Remove the fuel sender assembly and the seal. Discard the seal.
  • Note the position of the fuel strainer on the fuel sender. Support the fuel sender assembly with one hand and grasp the strainer with the other hand. Pull the strainer off the fuel sender. Discard the strainer after inspection. Inspect the strainer. Replace a contaminated strainer and clean the fuel tank.
    • Fuel pump electrical connector
    • Electrical connector retaining clip from the fuel level sensor
    • Sensor electrical connector from under the fuel sender cover
    • Fuel level sensor retaining clip
  • Squeeze the locking tangs and remove the fuel level sensor.
  • Remove the fuel pressure sensor.
  • To install:
    1. Install or connect the following:
      • Fuel pressure sensor
      • Fuel level sensor
      • Sensor retaining clip
      • Electrical connector to the fuel level sensor
      • Electrical connector retaining clip to the fuel level sensor
      • Fuel pump electrical connector
      NOTE Always install a new fuel strainer when replacing the fuel tank fuel pump module.

      • New fuel strainer in the same position as noted during disassembly. Push the strainer on the bottom of the fuel sender until the strainer is fully seated.
      • New seal on the fuel tank
      NOTE The fuel pump strainer must be in a horizontal position when the fuel sender is installed in the tank. When installing the fuel sender assembly, assure that the fuel pump strainer does not block full travel of the float arm.

      • Fuel sender assembly into the fuel tank
      • Fuel sender assembly retaining ring
      • Fuel tank. Install the fuel tank strap attaching bolts. Tighten the bolts to 30 ft. lbs. (40 Nm).
    2. Refill the fuel tank. Install the fuel filler cap. Connect the negative battery cable.
    3. Turn the ignition ON for 2 seconds.
    4. Turn the ignition OFF for 10 seconds.
    5. Turn the ignition ON.
    6. Inspect for fuel leaks

    Oct 25, 2009 | 2002 GMC Sierra 1500

    2 Answers

    Whats the best way to replace fuel pump ? drop the tank or the bed


    According to the factory service manual, you should drop the tank, there are pictures and diagrams with these in the manual.
    1. Disconnect the negative battery cable.
    2. Relieve the fuel system pressure.
    3. Drain the fuel tank. .
    4. Remove the fuel tank.
    5. Remove the fuel sender assembly.
    6. Note the position of the fuel strainer (2) on the fuel sender.
    7. Support the fuel sender assembly with one hand and grasp the strainer (2) with the other hand.
    8. Pull the strainer off the fuel sender. Discard the strainer after inspection.
    9. Inspect the strainer. Replace a contaminated strainer and clean the fuel tank.
    10. Disconnect the fuel pump electrical connector (5).
    11. Remove the electrical connector retaining clip (6) from the fuel level sensor.
    12. Disconnect the sensor electrical connector (7) from under the fuel sender cover.
    13. Remove the fuel level sensor retaining clip (4).
    14. Squeeze the locking tangs and remove the fuel level sensor (3).
    15. Remove the fuel pressure sensor (1).
    A good place to get an inexpensive service manual is from Promanuals it's a complete factory manual.

    Sep 26, 2009 | 2000 GMC Sierra

    Not finding what you are looking for?
    1994 Oldsmobile Cutlass Ciera Logo

    Related Topics:

    156 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Oldsmobile Experts

    yadayada
    yadayada

    Level 3 Expert

    76682 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22219 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8531 Answers

    Are you an Oldsmobile Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...