Question about 2004 Chevrolet S-10

1 Answer

I am looking for the factory torque settings for the front wheel bearings for a 2004 Chevy s10 pick up.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 14,036 Answers

IF YOU HAVE 4WD YOU WILL HAVE TO REPLACE BEARINGS.NOT ADJUSTABLE. IF YOU HAVE A 2WD YOU WILL REMOVE COTTER PIN AND LOOSEN THE SPINDLE NUT.SPIN THE WHEEL FORWARD BY HAND THE TORQUE NUT TO 12 FT LBS TO SEAT BEARING.THEN BACK OFF NUT 1/4 TO 1/2 TURN TO UNTIL HOLE IN SPINDLE LINE UP WITH SLOT IN NUT.THEN INSTALL A NEW COTTER PIN.

Posted on Sep 19, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace front brake pads on a How to replace front brake pads on a 2000 Chevy S10 4WD pickup?


First you want to remove brake fluid from brake resovoir, raise front wheels off ground and set park brake or block rear wheels. Remove front wheels, keep steering wheel unlocked so you can turn rotors side to side. Loosen bolts that hold caliper end gently pry caliper free from rotor, remove caliper and remove pads, use bungy cord to hang caliper away from rotor, have rotors measured to see if they are thick enough to have machined, replace if out of specs. Match up pads with old ones, use anti- squeak red liquid and put layer on back of pads, let dry. Use tool to put pistons back into calipers, slowly put pistons back into bore while opening up bleeder screw so ABS won't be damaged. After rotors resurfaced, wash with rubbing alchohal to remove any oils from hands, install rotors and reverse putting pads back onto caliper and reinstall, torque caliper bolts to factory specs and tighten bleeder screws. Install wheels, torque lug nuts to factory specs and replace brake fluid in resovoir. Lower car carefully to ground and press brake peddle without pumping it. Any air in system should bleed out, if not get someone to help with bleeding system. Road test to ensure no squeaks or pulling, burn brakes in slowly.

May 10, 2014 | 2007 Saturn Aura XR Sedan

1 Answer

Need torque specs for front wheel bearing on 2004 dodge 3500 dually


The hub bearing retaining bolts are 150 ft. lbs the center axle nut primary torque 135 ft.lbs rotate 5-10 times increasing torque by 50 ft.lbs until final torque of 265 ft.lbs is reached

Mar 23, 2014 | 2004 Dodge Ram 3500 Truck

2 Answers

What is the torque specs for a hub and bearing assembly on a 2001 four wheel drive chevy s10 blazer



Adjustment

The wheel bearings on these vehicles are not adjustable. If the bearings become loose or make noise, they must be replaced.


Removal & Installation

  1. Before servicing the vehicle, refer to the Precautions section.
  2. On 4WD vehicles, remove wheel center cap, if equipped, and the drive axle nut and washer
  3. Raise and support the vehicle.
  4. Remove or disconnect the following:
    NOTE Lay the hub and bearing on the wheel studs on the outboard side. This will avoid damaging the bearing seal.


    Tire and wheel Caliper, leaving the fluid lines connected Brake rotor Halfshaft from the hub and bearing on 4WD vehicles. Place a brass drift against the outer edge of the halfshaft to protect the shaft threads. Use a hammer to sharply strike the brass drift, but to do not remove the halfshaft at this time. Wheel speed sensor Wheel hub and bearing-to-steering knuckle bolts and hub and bearing


    Splash shield from the steering knuckle Seal from the hub and bearing

To install:
  1. Install or connect the following:

    Wheel hub and bearing seal Splash shield to the steering knuckle, making sure it-s properly aligned Hub and bearing to the steering knuckle, aligning the threaded holes Hub and bearing bolts and tighten to 77 ft. lbs. (105 Nm) Wheel speed sensor. Tighten the bolt to 13 ft. lbs. (18 Nm). Rotor and brake caliper Tire and wheel
    The Hub Bearing Torque - Front

    If Torque Specs are not in the box we recommend youtorque to this setting. Axle Nut: 103 Ft/Lbs.Flange Bolts: 77 Ft/Lbs. WARNING: Failure to observe the following warningscould create a risk of death or serious injury.Proper maintenance and handling practices arecritical.Always follow installation instructions and maintainproper lubrication.Every reasonable effort has been made to ensure theaccuracy of the information contained in thiswriting, but no liability is accepted for errors,omissions or for any other reason.This information is not intended to substitute forthe specific recommendations of your vehiclemanufacturer.Always use the recommended torque requirement unlessotherwise specified in the carton.Depending on the application, type of hub unitbearing and location, the installation process mayvary.Please review the vehicle manufacturer'srecommendation before removing or installingcomponents.
  2. Lower the vehicle
  3. On 4WD vehicles, install the drive axle nut and tighten to 103 ft. lbs. (140 Nm), then install the center cap.

Nov 10, 2012 | Cars & Trucks

1 Answer

What are mazda 6 wheel bearing torque specification


What is the front axle torque on a 2004 Mazda 6

Mar 17, 2012 | 2004 Mazda 6

1 Answer

Proper torque for bolts on front wheel


The axle nut spec is 177 foot lbs. and the bearing to knuckle bolts spec is 133 foot lbs.

Dec 23, 2009 | 2004 GMC Yukon

Not finding what you are looking for?
2004 Chevrolet S-10 Logo

233 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...