Question about 2000 Ford Focus

1 Answer

Removal of headlight assembly on a 2000 ford focus

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,986 Answers

There are 2 screws on top and 1 below the headlamp. The top ones are easy. You'll have to lie on your back to remove the bottom one as you'll have to reach up behind the bumper to get to it. It'll be close to the fender wall

Posted on Sep 11, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I get the rear drums off a 2000 Ford focus. I removed the spindle nut,


2000 Ford Focus Drum Removal ProcedureIf removing the drum to service the rear brakes: (note, do not remove hub retaining nut for this procedure)
1. Raise and support vehicle
2. Release the parking brake
3. Remove wheel and tire
4. Disconnect wheel speed sensor wiring harness from wheel knuckle and floor panel.
5. Remove 4 wheel spindle attaching bolts, then the wheel hub and drum assembly from vehicle.
6. Reverse procedure to install noting the following:
a. Torque wheel spindle retaining nut to 49 ft. lbs.
b. Torque wheel/tire assembly to 94 ft. lbs.
2000 Ford Focus Drum Replacement ProcedureIf replacing the drum and wheel bearing assembly:
1. Raise and support vehicle
2. Release the parking brake
3. Remove wheel and tire
4. Remove center dust cap.
5. Remove hub retaining nut.
6. Remove drum and hub assembly. Ensure wheel speed sensor ring is not damaged when removing drum/hub (if equipped).
7. Reverse procedure to install noting the following:
a. Inspect and clean wheel speed sensor ring if equipped.
b. When tightening hub retaining nut, rotate the hub assembly in counterclockwise direction.
c. Torque hub retaining nut to 173 ft. lbs.
d. Torque wheel/tire assembly to 94 ft. lbs.
e. Adjust parking brakes as necessary.


Jul 05, 2011 | 2000 Ford Focus

1 Answer

How to change the headlight assembly on a 2000 Ford Focus


Information for replacing the headlamp bulbs is covered on page 234 of the Owner's Manual.
If you need an owner's Manual, you can download a free copy (PDF Version) from Ford. Just click the link below.
2000 Ford Focus Owner's Manual

If you are wanting to replace the entire headlamp assembly, There are 4 screws holding the lamp assembly in. This link has pictures and instructions that will get you through the removal process.
Ford Focus HID Headlamp Upgrade Step 2

Apr 28, 2011 | Ford Focus Cars & Trucks

1 Answer

How do I change a headlight unit in a ford focus as I cannot find the bolts


Open your hood and look at the headlight assembly from inside the hood. You will see screws that you can loosen to get the headlight covers off, and the bulbs should just be "screwed" in the headlight units. There shouldn't be any bolts and screws on the outside. Also, to adjust your lights, you should have an adjustment "screw" on top of the headlight unit when you open the hood.

Dec 30, 2010 | 2000 Ford Focus

1 Answer

Headlight bulp replacement, passenger side, removing bulb from back of assembly without removing entire assembly


The bulbs most likely are a three tab twist and turn replacment.

Depress the clip at the back of the bulb for wring harness and pull gently straight back twords pass compartment, twist bulb assy to left( about a 1/4 turn when it stops gently pull towrards pass compartment.

Reverse the process to install new bulb.

Oct 30, 2010 | 2000 Ford Focus

1 Answer

How to change a front light bulb


p, li { white-space: pre-wrap; }
  • Ensure that the headlights on your Ford Focus are off by checking you have turned the headlight control all the way to the off position. Make sure your car is off and the keys are out of the ignition, so the daytime lamps are also off.
  • Open the hood using the hood release handle located inside the vehicle under the steering wheel on the left side of the instrument panel. Walk around to the front of your Ford Focus and release the auxiliary latch located under the front of the hood. Lift the hood and secure it in place with the yellow end of the hood's strut in the designated holes.
  • Locate the bulb cover found just behind the headlight assembly and remove it by turning it counterclockwise. Swivel the wire clip that hold the bulb and connector in place out of the way by turning it to the left.
  • Pull out the headlight bulb with its electrical connector straight out from the headlamp assembly.
  • Disconnect the bulb from the connector. Later editions of the Ford Focus may have a retaining ring that lies between the bulb and electrical connector. Simply remove this retaining ring by twisting it off with a counterclockwise turn.
  • Install the replacement headlight bulb in reverse order of removal. Use a HB2 replacement bulb for models older than 2004 and a HB5 bulb for models produced since 2005. Replace the wire clip and bulb cover, as well.
  • Turn on your Ford Focus and check that the headlights are working properly after closing the hood.

Aug 26, 2010 | 2003 Ford Focus

1 Answer

Changing a headlight on a ford focus 03


headlight bulb or assembly? remove the fender splash shield lower retaining screw. Push the fender splah shield to inside. Remove the headlamp assembly lower retaning bolt. Remove the grille. Remove the head lamp assembly

Jun 21, 2010 | 2001 Ford Focus

1 Answer

How do you remove a headlight 'assembly' (not the


You have to remove the front bumper cover. Put the car on jack stands (the front) and remove the inner fender plastic. You'll need a long extension and a 10mm socket to remove the nuts and bolts holding the bumper cover in place. Once the cover is off removal of the headlight becomes obvious.

May 15, 2010 | 2000 Ford Escort

2 Answers

How to get headlamp out from ford fiesta 03


If you're just replacing the bulb, you access it from the rear of the headlight assembly. Just sqeeze the nylon locking device, and turn it counter clock wise, then pull the bulb out, and replace.

Dec 27, 2009 | 2000 Ford Focus

1 Answer

Headlight replacement on ford focus 2000


To replace burnt bulb easiest way is to remuve head lamp assembly.Few screws.

Nov 30, 2009 | 2000 Ford Focus

2 Answers

Headlight lens removal


Open hood and look at top back of the assembly and you will see 2 clips. Pull them up and remove,then release the lower clip and pull assembly out.

Apr 08, 2009 | 2000 Ford F250 Super Duty Crew Cabs

Not finding what you are looking for?
2000 Ford Focus Logo

408 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75824 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...