Question about 2001 Dodge Ram 2500 Truck

2 Answers

How To Remove the harmonic balancer on a 2001 ram

How To Remove the harmonic balancer on a 2001 Dodge ram 2500 v-10 and install the new one. Do I have to pull the radiator?

Posted by on

Ad

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

  • Expert
  • 83 Answers

Here is a link to a 2001 Dodge Ram Factory Service Manual with diagrams and step by step procedures.

Posted on Sep 27, 2009

Ad
  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 31 Answers

Yes. at the very least the fan shroud and fan.

Posted on Sep 18, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2001 dodge stratus r/t 3.o liter outside pulley on harmonic balancer fell off. do i need whole new balancer or is there something that came off that holds it on?


ON most engines there is only on pulley as part of the harmonic balancer. It is the on that has the rubber between the pulley and the center bit on the crank. Any other pulleys are normally bolted to this pulley on the center hub piece . I'm thinking that the mount bolts have fallen out.

Apr 20, 2013 | 2001 Dodge Stratus

1 Answer

A piece of material came out of my harmonic balancer and I dont have any brakes, steering, and its not charging what is the problem.


Sorry to tell you this but you need to get a new harmonic ballancer wheel.
The rubber that came out is part of the whole constructed unit.
The rubber lining inside the housing helps balance out any vibration in the belt assembly.
The rubber has to be inside the grooved drum that the belts attach to powered by the crankshaft,so no rubber inside is like driving your car without tires on the rims.
Slip around nice eh? so does the gap between the belt housing and the pulley that's attached to the crankshaft.

Nov 25, 2010 | 2001 Dodge Ram 2500 Truck

1 Answer

How do i remove the harmonic balancer from a 2001 dodge dakota with a 4.7 L moter


You have to have a harmonic balancer puller that you can rent at you local parts store.

Aug 09, 2010 | Dodge Dakota Cars & Trucks

1 Answer

How to replace harmonic balancer?


jack up vehicle ,remove passenger side front tire remove plastic splash shield now under hood find your serpentine belt tensioner release tension on belt and remove belt now back at the plastic shield with it removed you should see your harmonic balancer install correct puller onto balancer and remove

Mar 16, 2010 | 2001 Buick Century

1 Answer

Crankshaft sensor on a Monte Carlo 2001 SS 3.8 where is this on the car and how to replace it?


3.8L Engine
  1. Turn OFF the ignition.
  2. Remove the serpentine belts from the crankshaft pulley.
  3. Raise the vehicle.
  4. Remove the right front wheel and tire assembly.
  5. Remove the right inner fender access cover.
  6. Hold the flywheel with a (J 37096) flywheel holding tool.
  7. Using 28 mm socket, remove the crankshaft harmonic balancer retaining bolt.
  8. Remove the crankshaft harmonic balancer, using a (J 38197-A) balancer remover.
  9. Remove the crankshaft position sensor shield (1). Do not use a pry bar.
  10. Disconnect the sensor electrical connector.
  11. Remove the attaching bolts from the crankshaft position sensor.
  12. Remove the crankshaft position sensor from the block face.
To install:
  1. Position the crankshaft position (CKP) sensor to the block.
  2. Install the bolts to hold the CKP sensor to the block face. Tighten the bolts to 14-28 ft. lbs. (20-40 Nm).
  3. Reinstall the crankshaft position sensor shield.
  4. Connect the CKP sensor electrical connector.
  5. Position the crankshaft harmonic balancer on the crankshaft.
  6. Hold the flywheel with a (J 37096) flywheel holding tool.
  7. Using a (J 36660-A) torque/angle meter, tighten the harmonic balancer bolt to 110 ft. lbs. (150 Nm), plus an additional 76 degrees.
  8. Install the right inner fender access cover.
  9. Install the right front wheel and tire assembly.
  10. Tighten the wheel nuts to 104 ft. lbs. (140 Nm.).
  11. Lower the vehicle.
  12. Reinstall the serpentine belts.

It looks like this:

fd368a5.jpg

Jan 10, 2010 | 2001 Chevrolet Monte Carlo

2 Answers

How to remove the harmonic balancer pulley on a '96 dodge caravan 3/0L?


i have a 1998 caravan my harmonic balancer fell off my qquestion is is there 2 separate keys that hold on the timing gear and the balancer pulley on, i have been to the dodge dealer and they printed me out pics but i still don't know for sure if the timing gear has it's own key or there is just 1 long key that holds both the timing gear and the balancer ......PLEASE HELP

Nov 22, 2009 | 1996 Dodge Caravan

1 Answer

2001 Dodge 4x4 diesel 6-speed. Replaced clutch and pressure plate, now the starter won't turn the engine over.. Tried turning it over with the harmonic balancer, and the output shaft on the x-fer case. No...


One problem pops into head when I think about your description of the problem. The bolts that hold the pressure plate to the flywheel may be too long, causing the engine block to interfere with the rotation of the flywheel.

Nov 17, 2009 | 2001 Dodge Ram 2500 Truck

1 Answer

I have a 97 dodge v-10 truck. wont fire


if the timing is off by 180' this will do it or there is a ckank sencer on it and it should be looked at if knoked or banged could be bad..

Jul 09, 2009 | 1997 Dodge Ram 3500 Club Cab

1 Answer

1988 dodge ram 50


Greetings!
Further to Tinkertoys1's note...

Yes, the harmonic balancer is manufactured to only fit on one way.
Now, knowing this, the harmonic balancer has a timing mark set into the outside area of the balancer.

Cheers, Jay

May 18, 2008 | 1988 Dodge Ram 50

Not finding what you are looking for?
Cars & Trucks Logo

739 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8531 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...