Question about 2002 Dodge Caravan

2 Answers

Broken rear wheel stud how do i repair it - 2002 Dodge Caravan

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Dodge Master
  • 6,982 Answers

You will need to tear it down to the point where you can get to the back of the stud. Stride it hard on the broken side with a decent weight hammer and it will come out the back...If drum brake, make sure it's in a position where it will not hit the brake assembly, or, remove brake shoes to make room. To install, put a stack of washers on the threaded portion and put the wheel lug nut on backwards (flat side in.) oil the threads. Tighten the lug 'till the stud has been pulled all the way in, then put everything back together.

Posted on Sep 11, 2009

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 3,600 Answers

The stud has to be hammered out if you don't have the tools to do this then I suggest you take it to a tire shop they don't charge much. depending if it's front wheel or rear wheel drive will determine what has to be done. If it's a rear axle they will remove the tire and drum and knock out the old one with a hammer and punch and replace it with a new one same size, they can hammer it back in our use washers to pull it into place this is the same on the front wheel. You will need to measure the bolt to get the right length and width. tire shop will have the stud you need.

Posted on Sep 11, 2009

Testimonial: "i had heard that was the right way to fix it .know i know for sure.thank you."

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

  • 834 Answers

SOURCE: I am wanting to replace the rear wheel studs that

You do not remove the wheel hub flange, just follow the procedure that I replied to earlier, and this is the procedure if you do not want to obtain a special tool for pressing the lug studs;

First you will have to pound the broken lug studs out of the wheel hub, then you will need a lug nut and about a half an inch thick of flat washers.

1. Insert the new lug stud through the wheel hub from behind so that the threaded end is facing out towards you and then put some grease on the threads.

2. Then slip the flat washers onto the lug stud followed by the lug nut, and run the lug nut down to take up the slack.

3. Then using a breaker bar tighten the lug nut until it pulls the lug stud through the wheel hub and it is flush with the wheel hub.

Be sure that the amount of flat washers used will make up for any non-threaded part of the lug stud that might stick out past the wheel hub preventing the lug nut from pulling the lug stud all the way through the wheel hub, and basically you do not want the lug nut to run out of threads before it can pull the lug stud flush with the wheel hub.

Posted on Jun 13, 2010

davidsspa572
  • 51 Answers

SOURCE: wheel studs or bolts

Hello Miguel Thank you for using FixYa.com my name is David I hope this Helps you out.
Studs often get damaged from overtightening or from cross threading a nut on the threads. A damaged stud is replaced by unscrewing it from the part and installing a new one of the exact same size.
Stud replacement can be difficult because the stud has often been in place for a long period of time. There has been constant heating and cooling, corrosion, and rust buildup between the stud threads and the internal threads of the part. These factors combine to make some studs very difficult to remove.
The first step in stud removal is to use penetrating fluid to remove the corrosion to free the stud from its mating threads. Soak the area of the threads with penetrating fluid. Allowing the fluid to soak into the threads overnight will make it easier to remove the stud.
Before removing the old stud, measure the distance it sticks up from the surface. This measurement will be needed later when installing the new stud. Use a 6-inch scale to measure from the part surface to the top of the stud. Write the measurement down so it can be referred to later.
A stud remove is used to remove studs. It is installed over the stud. The jaws on the stud remover grip the outside of the stud. A wrench fits on the stud remover and allows the technician to rotate the stud in a counterclockwise direction to remove the stud.
If a stud remover is not available, a stud can be removed with two nuts. Locate two nuts that are the correct thread size. To thread onto the stud. Start one nut and thread it all the way down to the bottom of the stud. This nut will be the drive nut. Start another nut and thread it down until it contacts the first nut. This is called the jam nut.
Put a wrench on the bottom drive nut and hold it in place. Put another wrench on the jam nut and tighten, or "jam" it against the drive nut. The jam nut will now hold the drive nut in position on the stud.
Now put an open-end wrench on the bottom drive nut. Turn the nut in a counterclockwise direction. Turning the nut in this direction causes it to want to unscrew the stud. Instead the forces cause the stud to unscrew.
When the old stud is out, inspect the internal thread. If it appears rusty or damaged, clean up the thread by running the correct size tap through the threads as previously explained. Compare the new stud with the old one. The studs should be exactly the same thread size and the same length.
Check the vehicle's service manual to determine if the threads of the new stud should be coated. If the stud should be locked in place and not easily removed, you may need to use a threadlocking compound or threadsealing compound. Threadlocking compounds are on studs and other fasteners when vibration might cause them to unscrew. Thread sealants are used when a stud extends where liquids, such as oil or coolant, could get on the fastener.
Antiseize compound is used on the stud threads to prevent the stud from reacting with the metal on the internal threads. If this happens, the stud could stick or seize. Antiseize compound prevents this reaction and makes the stud easier to remove the next time.
After the new stud is properly coated, it can be installed. Start the stud by hand, making sure it enters the threads securely. Turn the stud in as far as possible by hand before using any tools. Then use two nuts as described earlier to drive the stud into the part. Use the depth measurement made on the old stud to be sure it is driven in the correct depth.

upper_left.gif grey_line.gif upper_right.gif grey_line.gif Look for More Parts A B C D E F G H I
J K L M N O P Q R
S T U V W X Y Z grey_line.gif lower_left.gif grey_line.gif lower_right.gif Related Parts: grey_line.gif 0900823d80050bfd.gif Wheel Nut

Posted on Nov 06, 2008

SOURCE: Two Broken Wheel Studs on Front Driver's Side

It would be best to have the work carried out at a garage of your choice. A garage you have used before and trust to do a good job. Depending how long it takes to free the studs, will depend on the final price.

Posted on Dec 01, 2008

MrScary66613
  • 1990 Answers

SOURCE: Procedure for replacing broken rear wheel stud on 1988 dakota.

It is a Knockout Stud. It will take quite a bit of force to get it out to. The new stud just goes in the Same way. Use a little WD 40 on Install for easier insert. The Lug Nut will keep it from getting loose.

Posted on Jan 23, 2009

F.U.B.A.R.
  • 19 Answers

SOURCE: two broken lug studs. 07 Nissan titan 4X4.

They should be replaceable w/o pulling the axle. Imagine a common nail; you have the shank of the nail with its point and the flat head on the other end. Your lug stud looks a little like that except the part that comes through the axle flange. It is a little larger than the threaded part and has "lateral lines" machined into it to grip inside the flange. Otherwise it would spin either way when you tried to tighten or remove it. To get the broken ones out, use a high quality flat end punch and a hammer to drive them backwards (toward the center of your differential) and eventually out of the flange. Look for the area that will give you the most room so they will not hit aything while they are backe out of the flange. The new studs can be installed in the reverse manner. When you get them just barely started through the flange, use your fingers to twist them back and forth to "feel" for the grooves where the old stud was seated. Once you get it barely started in the grooves, grease the threads, slip an old 1/2 inch drive socket over the new stud (make sure it doesn't fit tight) slip on a thick flat washer or 2--3 thin ones, turn your lug nut around backwards so the tapered end faces out and begin to tighten it. Go slow, make sure the new stud pulls through the flange evenly. Take the nut, washers and socket off every now and then and look at your progress. When the back side of the stud is seated on the back of the flange, you're finished. Now, always grease the studs. ALL OF THEM, EVERY WHEEL. The monkeys that put on tires these days use impact wrenches and if you just have to let them do it, grease will help you loosen the nut if you have to and it will help prevent future failures. A DRY stud and nut causes a twisting motion to take place in the body of the stud when its tightened. This leads to premature metal fatigue.

Posted on May 03, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

E2000 broken left rear wheel studs


Hammer them out and hammer them in. Make sure to line up with the old splines when putting in the new ones.

Aug 30, 2014 | 1988 Mazda B2200

1 Answer

How to replace a rear wheel stud


remove the wheel
using a hammer and punch knock the broken stud out
fit the new stud from behind use over size nuts as spacers fit the stud nut and apply tension
using the hammer and punch from the rear on the head of the stud knock it in as you keep the tension on the stud nut
keep the process going until the stud is fully seated on the head of the stud

Jul 10, 2014 | 2005 Toyota Camry Solara

1 Answer

2006 dodge caravan with rear draum brakes. Broken wheel stud on right rear wheel. Got the drum off, got the broken stud off. but i cant get the new stud in. not enough space to get the new stud in. Is...


Make sure all tires are chalked,put vehicle in neutral,turn drum till it has a clear spot to knock stud out,use hammer and wooden block,don't use metal punch,can cause burr on end of stud and not want to come out of hole.Both tires on back may need lifted in air to turn.

Jul 05, 2017 | 2006 Dodge Grand Caravan

1 Answer

Broken wheel studs on a 1987 jeep wrangler


No need to replace the hub just the studs. The come in from the back and are splined to prevent the stud from turning with the nut. Remove the hub --drive out the broken studs and put the new ones in from the rear and drive them back in. Get the studs from the dealer spares or a good tyre retailer.

Apr 08, 2013 | 1987 Jeep Wrangler

1 Answer

How do I replace a broken lug nut out of 98 windstar?


you don`t say if its front or rear lug nut(assuming you mean stud).remove the wheel and then the drum or rotor,then take a hammer and hit the broken stud to remove it from the hub assembly.with the correct wheel stud insert it through the hole and make sure its in straight,install the wheel nut and tighten the nut to pull the stud into the hub until all the way in.you may have to install washer on the stud and re-install the nut and tighten until the stud is seated all the way.

Sep 16, 2011 | 1998 Ford Windstar

2 Answers

2000 Dodge Caravan....broken wheel studs...


Yeah , it's a fairly simple repair, All the wheel studs must be replaced and lug nuts also.Closely examine the wheel or get competent tyre replacement company to double check for damage ! Remove the brake disc caliper and brake disc itself (usually 2 cross head screws) , tap off (gently) it may be stuck thru corrosion / rust etc , Broken studs can be knocked out(towards drive shaft ) of the hub assy with a suitable drift and hammer (splined into hub) . The studs are a servicable replacement part. Check all other wheel nuts as this is usually a result from poor fixing or wheel replacement recently .. Good luck

Apr 05, 2010 | 2000 Dodge Caravan

1 Answer

How do I replace the studs on the rear wheel


remove wheel and brake assembly, drive broken stud through back off the hub. Put new stud through hole and use a spacer and an old lug nut to pull stud till its seated in hub.

Feb 27, 2010 | 1993 GMC Suburban

1 Answer

Broken rear wheel stud on a 2005 ford focus zx4 se


  1. Step 1 Buy a new stud. Make sure you purchase the right size. If you're not sure what size to get, wait until you remove the stud and take it with you to the store.
  2. Step 2 Check the area of the spare tire in the trunk for the jack and the jack tools since you'll need to raise the car to replace the wheel stud on your Focus. Be sure to block the tire diagonal to the jack.
  3. Step 3 Use the jack to raise the Focus. Remove the wheel Take off the caliper and either hang it by a mechanics wire or lay it up so it doesn't dangle by the brake line. Remove the rotor. If you're working on back wheels, you have to remove the emergency brake clip first. You could have drum brakes in the rear. If they're drum brakes, remove the drum.
  4. Step 4 Hunt for an opening behind the hub that allows you to remove the stud. Line the stud up with the hole. You may have to take off the hub and put it in a vise if you can't drive it out the back.
  5. Step 5 Hit the stud with a mallet and drive it out the back of the hub. Push another stud into the opening. This is tough work, but you only need to push it far enough to thread on a wheel bolt.
  6. Step 6 Put on a wheel bolt and begin to tighten it. As you do, the stud starts to pull through. Add more bolts as necessary until you seat the stud. Check in the back of the hub. When the head is flush with the stud, you seated it.
  7. Step 7 Remove the extra bolts and reassemble the parts that you took off to replace the wheel stud on the Ford Focus. Put the wheel back on the vehicle and tighten down the wheel nuts.

Sep 25, 2009 | 2005 Ford Focus

1 Answer

Broken wheel stud


1. get new studs and nuts
2.remove wheel
3. remove caliper at bracket to spindle connection(2 18mm bolts?)you may need to remove caliper from bracket,but not always nessacery. Or remove drum,then to #5
4.remove rotor,will need a hammer, tap inbetween studs dont wreck good studs and see if new studs can be installed without removing parking brake shoes. If there is no clearance to get new stud in you will need to remove shoes.
5.Pound out old studs place new stud in hole use a washer on outside then put a nut on and tighten to install stud, A air gun or some type of impact tool will be very helpful. Check to see that stud has enough threds to pull stud all the way thru ,add more washers if nessecary dont let the nut run out of threds it will **** to get back off and wreck new stud.
6. if you dont have air gun or feel comfertable removing brakes bring it to a reputable garage, shouldnt cost more than $70+ parts to get all new studs put in on one wheel.

May 17, 2009 | 2002 Nissan Sentra

2 Answers

Broken lug stud on rear wheel.


It appears from the excellent picture that the stud has to be spun to line up the half moons at the rear of the stud.Use two thin nuts locked together so you can spin the remaining stud to line up with reliefs in back of the retainer.

Oct 18, 2008 | 2004 Buick LeSabre

Not finding what you are looking for?
2002 Dodge Caravan Logo

506 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...