Question about 1991 Chevrolet Suburban

2 Answers

I have a 1991 chevy suburban and the parking lights do not turn on but turn and brake lights work. what could it be?

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 3,600 Answers

Check the light bulbs first; if the bulbs are ok then you most likely have a bad light switch. It costs $15.00 and not to hard to replace, if you need help with this post here and I will give you instructions on how to replace. I assume you don't have a volt ohmmeter.

Posted on Sep 11, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Give me instructions or how to change the light switch and where is it located

Posted on Mar 25, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My 1991 buick park ave shifter is stuck in park,it cranks but cant move shifter to reverseod drive to move car,can you help,tony.


have you tried starting it . sitting in the seat and pushing down the brake pedal then the shifter .\while holding brake down. I do not have a buick but that is how chevy truck toyota car and toyota truck work

Feb 03, 2015 | 1991 Buick Park Avenue

1 Answer

My brake lights work and head lights but no running lights on my 1991 chevy truck 4x4


Did you check the park fuse, or the orange wire going into the headlight switch for power ?

Feb 09, 2013 | 1991 Chevrolet C/K 2500

1 Answer

DISCONNECT BRAKE PEDAL 1991 SUBURBAN


98 Suburban 5.7L, automatic trans is stuck in park - no previous shifting problems, I know that the brake switch also operates the brake/transmission solenoid (BTS). Stepping on the brake pedal prior to starting the vehicle allows shifting from park to another gear. When I switch the key to the "on" position, I don't hear the BTS click. I can start the vehicle and the brake lights work fine. I just can't shift out of Park. I am unemployed and I am trying to troubleshoot this problem and fix it myself. Please help!

May 24, 2012 | 1983 Chevrolet Silverado

1 Answer

How do I reset the service brakes soon light on a 2008 chevy suburban


{: ) It depends on how serious the fault is. It could be the wirings. However you can at least try these steps. The most important is to check for proper brake fluid level, and carefully inspect for brake fluid leaks. Check also your brake lights if working properly. Also check the parking brakes if the light responds as you engage or disengage the park brake lever.

Aug 27, 2010 | 2008 Chevrolet Suburban

1 Answer

2003 Chevy Suburban - where is the parking brake sensor located?


This is part of the parking brake assemly pedal. If you are looking for it to diagnose, it is on top of the assembly. it is a one wire white connector. If light is on and this is suspected to be the problem, unplugging it will shut the light off if this is the problem. If light is still on after you un plug it then it may be the master cylinder resivior switch, or the brake fluid is low. I hope this helps.

Dec 31, 2009 | 2003 Chevrolet Suburban 1500

2 Answers

Suburban stuck in PARK


I accidently posted under 2004 Envoy - actually a 1997 Chevy Suburban. Found the switch on the brake actuator rod, sprayed with WD 40 (sloppy - hit or miss) - and moved the switch around. Now works fine. If I could find a way to remove the switch, I would replace. I may find the wires for the power and release servo and jump those out with a remote switch in case of future problems.

Jun 02, 2009 | 2004 GMC Envoy

2 Answers

Parking break light is on & Chimming When P. Break is released


On your parking brake assembly is a single wire switch. You can unplug it, but you will have to remember not to drive with it set. To replace the switch the whole assembly will have to come out. The switch is about $20 and labor should run about two hours. Good Luck

May 20, 2009 | 2003 Chevrolet Suburban 1500

1 Answer

No running lights when head lights are on


the brown wire on your suburban will be your park lights and the yellow will be brake/turn are you sure the green wire is ground on your led lights? i would think the black wire would be ground

Nov 25, 2008 | 1988 Chevrolet Suburban

2 Answers

No turn signals or side brake lights on 94 chevy suburban


the problen is probably the turn signal switch with a test light check for power at brake switch if no power check for power at turn signal switch the brake lights are incorperated through the turn signal switch

Oct 18, 2008 | 1994 Chevrolet Suburban

Not finding what you are looking for?
1991 Chevrolet Suburban Logo

128 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...