Question about 1993 Audi 90

1 Answer

How to replace an ignition switch, to a 1993 Audi coupe 2.0

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 2 Answers

That's easy, remove instument cluster,remove bottom shelf (above brake pedal,) now u have acsess to ignition switch.reach thrue instrument clust. opening on dash,push back ign.plug from switch, use small flat blade scewdriver and remove 2 small screws or loosen them and push out ign.switch (repl. with new one)

Posted on Nov 30, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Ignition sitch fails to operate


Apr 20, 2014 | 1993 Audi 90

1 Answer

How to replace the ignition switch on a 1993 audi 90s

Ignition switch is on the opposite side of where u start the vehicle with the key, so u have to take the ignition off may have to take the radio off if it helps on this model then u have to take off a couple plastic peaces off to see the ignition switch and to replace

Mar 01, 2011 | 1993 Audi 90

3 Answers

How do I replace my ignition switch on my 1985 audi coupe gt?


The ignition switch is usually mounted to the steering column and is operated by a linkage rod.

On column-mounted ignition switches, don't confuse the switch with the lock cylinder and keys. The ignition switch is not normally visible.
On some vehicles, the steering column support has to be removed and the column lowered to find the ignition switch. On others, the switch is accessible under the dash

The ignition switch is operated by the key switch.

To replace the switch:
  • Remove the ignition switch wiring harness.
  • Unbolt it from its position.
  • Bolt the new switch into position.
  • Attach the witing harness.
Don't forget to rate this post!! Good Luck!!

Jul 24, 2010 | 1985 Audi GT

1 Answer

I have a 1993 Audi V8 Quattro with electrical issues, wont start.

have you figured it out yet? i can sell you a used starter if you need one. i have alot of parts for this car.

Oct 10, 2009 | 1990 Audi V8 Quattro

1 Answer

How do you remove a petrol pump from an audi coupe

Wouldn't you think that obvious..?

Take out the petrol pump from the Audio Coupe, try wiggling it out so it comes out but don't force it otherwise it might brake some wires or near-by environment.

Sep 03, 2009 | 1993 Audi 90

1 Answer

1988 audi 80 4cyl. no spark from coil,new coil fitted,coil lead

hi i have a coupe 1994 have same prob told by audi to replace the distributor as was common failt on audi's i have replaced new leads ,coil ,dissy cap, and arm ,still the same awaiting on distributor to see if this works hope this helps

Apr 27, 2009 | 1988 Audi 80

1 Answer

Electrical problem 1993 Audi 90 CS

The 1993 90 instrument cluster is very sensitive.  Even having bulbs out can mess it up.  You should consider replacing the ignition switch.  It is easy you can do it yourself, do NOT let Audi dealer's service tell you it's $500 to do it.  You can get the part for less than 30 bucks on ebay.  Undo the screws under the steering wheel, take off the plastic, take out the 2 screws on the instrument cluster, take out the cluster enough to see the ignition switch.  THis is the tricky part:  get a small screw driver and LOOSEN the small screws that keep the ignition switch in place.Replace.  Re-tighten, put it all back and you're done.
Ignition switch is EVERYTHING in this car.  Oh, do not by the switch with the pink plastic where the key would go, buy the WHITE.

Jan 19, 2009 | 1993 Audi 90

1 Answer

Audi coupe 23e

This sounds like an ignition problem, most likely the ignition module, they are $38 on line at

Oct 22, 2008 | 1991 Audi 80

1 Answer

I have a 1991 audi 100, when i put the key in the lights come on but it wont crank its like the battery is dead, i tested the starter its fine what else could i check?

I had the same problem last year. It turned out to be the ignition switch. This could be the problem for you, maybe?

Jul 22, 2008 | 1993 Audi 100

2 Answers

Ignition key removal

It is the magnet inside the ignition block (the barrel where you put key in) . Usually you fix this problem replacing the ignition block.

Jun 08, 2008 | 2008 Audi A5 Coupe

Not finding what you are looking for?
1993 Audi 90 Logo

Related Topics:

604 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audi Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers


Level 3 Expert

76846 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14384 Answers

Are you an Audi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides