Question about 1991 Nissan Pathfinder

Open Question

1991 pathfinder the control bar from the lock barrel has disconnected from the locking mechanism there are plastic parts on that control bar one is a little yellow thing that needs to fit to a hole in a metal piece on the locking mechanism then a bigger white plastic cover has to go over it, I have been unable to get this to go back into place please help me fix my door locks this has happend to both locks on my front doors

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
jsrock516
  • 5911 Answers

SOURCE: Getting a small plastic piece out of a door

If the piece is jammed (locked) in the door latch assembly, there is a manual release that you can use to open the door latch to see if the piece will come from free. The following link advises:

http://www.fixya.com/support/r622155-kenmore_elite_whirlpool_duet_door_jammed

This may require two people. One to pull on the manual release, while the other works on retrieving the broken piece from the door latch.

Another method may be to remove the door latch assembly so you can easily manipulate it outside the machine. This link explains how to remove the door latch assembly:

http://www.fixya.com/support/r587965-door_latch_replacement_fdl_error

Now...if the piece is jammed too far inside the door latch assembly, a last resort would be to replace the latch. I hope it does not come to that, but it may be a last resort. The link provided will give you all the necessary steps to complete this repair, if required.

I hope you find this information helpful. Let me know if you require additional assistance.

Posted on Nov 08, 2008

Ad
  • 1027 Answers

SOURCE: Stripped threads on barrel of focuser

Meade sells replacement parts.

Posted on Apr 13, 2009

  • 119 Answers

SOURCE: driver side car seat side panel will not stay latched

you need new clips ,avable through subaru,i believe they are better than ones equipped originally

Posted on Jul 16, 2009

  • 27 Answers

SOURCE: iv taken ignition barrel off iv got a bit of metal

can u not use a stong magnet r twesers to retreve it ? if not ther shud b littel grub skrew or ser clip that will need to b taken out then it shud pull aprt b curefull lots of fidely bits that can b lost

Posted on Oct 04, 2009

Shorty1_wt
  • 324 Answers

SOURCE: Rusted out floor pan on Pathfinder...Need patch panel source.

try JC Whitney they offer repair floor panels for many vehicles.

Posted on Feb 12, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i drill the ignition lock cylinder out of my 1991 nisan pathfinder without distorting the column


you can di it by simply drilling down the key slot
However if you get it wrong then the hole for the barrel will be damaged and you will have to replace the whole assembly
Big job
get a locksmith to do the job and have him to reset the barrel to existing door locks so that you still only need one ley

Apr 22, 2015 | 1991 Nissan Pathfinder

1 Answer

I have a 97 Grand Marquis, and tried to start it. The electronics came on, but the car didn't turn over. I turned the key to "off" and removed it, but the electronics stayed on. I can even remove the...


the lock isnt turning the back part which is the contact switch,use a screwdriver to turn it off or disconnect the battery. I think the problem lies in the barrel is got a piece broken that goes from the barrel to the contact switch .Without seeing it myself i couldnt tell you whats wrong or why the barrel has come out but their is a small hole in the case where you can push in to remove the barrel but in all honesty ask a local mechanic to have a look for you as this mat be beyond the average hme mechanic to sort out also their is a security reader that reads the chipped key callled a transponder so a local mechanic who knows what hes doing is your best best .Sorry if this appears a negative answer but as stated i would need vehicle in front of me to diagnose the correct repair.

May 01, 2017 | 1997 Mercury Grand Marquis

1 Answer

Repair front door key lock on drivers side.


The is a bar that's runs up to the lock and is held in place by a plastic clip they all break eventually replaced a hundred of them good luck it's not hard but you have to take the door panel off and go through a small hole to do it

May 21, 2013 | 1993 Nissan Pathfinder

1 Answer

Bonet is stuck, put the key in turn it left and its not opening,


Look into the grill at the top you will find the bottom of 6 plastic screws, 4 you get two via the grill slots use a chisel and cut them off, Then one either end of the grill. Place the chisel between two plastic layers, gently lift , check and cut, one each end.
With a wiggle that's the top loose, There are two clips holding the bottom in place Put your fingers through the bottom slot in the grill, push down clip and greatly pull the grill, do both sides, It won't come right out but your aim to loosen it., The lock is held in place in a sleeve with a plastic clips each side, you have push the barrel with a suitable item, this is to push it out of the sleeve and out of its housing, It may need a tap!!
Gently wiggle and pull the grill off
Lock
The lock is a 'lock barrel along a shaft to a white plastic coupling' this fits in to the 'bonnet lock'
The security is at the coupling to bonnet lock in the form of a cross shaped plastic key
The key is fitted and held in place in the coupling, and when installed it's fitted in to the lock, and once it's in the lock part it will not come out, so therefore any jolt, pull, movement dislodges the plastic key from the coupling side and due to its design it will not slot back in so the lock barrel just rotates
To open you have to apply pressure on the shaft towards the left and into the coupling and turn the key in the lock barrel at the same time in a aim to get the coupling to catch the plastic key (take a few minutes) but it opens in the end if this is the fault, (alternatively remove the two bolts that hold the bonnet catch to the bonnet)
Once bonnet open remove the bonnet lock mechanism, then with draw the lock barrel, shaft, coupling, By looking in side you will understand regarding the cross key
Anyway you need to remove one of the catches from the side of the plastic key This way it will fit back in to coupling.
Reassemble

Mar 09, 2011 | 2006 Ford Focus

2 Answers

Lost the key to the back glass and door of my 91 s10 blazer. How do i unlock it from the inside?


u will need to remove the trim panel and use the lock release rods to unlatch the door.

May 14, 2010 | 1991 Chevrolet S-10 Blazer

1 Answer

CENTRAL LOCKING NOT OPENING BOOT


My passat boot lock does the same because someone forced the lock one night, i replaced the lock barrel but from time to time the white plastic acctuator or pump if you want to call it that jams in the open position and needs a small tap with the boot lining removed to free it up.A replacement is only £23(U.K pounds) or just spay a little lubricant in the mechanism to free up the mostly dry plastic parts.

Jan 13, 2010 | 2005 Volkswagen Passat

2 Answers

Mk 4 vw golf gti front door lock problems


Those components are probably part of a new lock assembly. Maybe locate a used lock to take those pieces from.

May 17, 2017 | 2001 Volkswagen GTI

3 Answers

Cant open bonnet of Ford Focus x reg grill operated key lock wont turn


Stuck lock, bonnet won’t open ,,,
You do not need to drill holes in the grill or pay ford £200+
DIY..How?
Look into the grill at the top you will find the bottom of 6 plastic revscrews, 4 you get two via the grill slots use a chisel and cut them off, Then one either end of the grill. Place the chisel between two plastic layers, gently lift , check and cut, one each end.
With a wiggle that’s the top loose, There are two clips holding the bottom in place Put your fingers through the bottom slot in the grill, push down clip and greatly pull the grill, do both sides, It won’t come right out but your aim to loosen it., The lock is held in place in a sleeve with a plastic clips each side, you have push the barrel with a suitable item, this is to push it out of the sleeve and out of its housing, It may need a tap!!
Gently wiggle and pull the grill off

Lock
The lock is a ‘lock barrel along a shaft to a white plastic coupling’ this fits in to the ‘bonnet lock’
The security is at the coupling to bonnet lock in the form of a cross shaped plastic key
The key is fitted and held in place in the coupling, and when installed it’s fitted in to the lock, and once it’s in the lock part it will not come out, so therefore any jolt, pull, movement dislodges the plastic key from the coupling side and due to its design it will not slot back in so the lock barrel just rotates
To open you have to apply pressure on the shaft towards the left and into the coupling and turn the key in the lock barrel at the same time in a aim to get the coupling to catch the plastic key (take a few minutes) but it opens in the end if this is the fault, (alternatively remove the two bolts that hold the bonnet catch to the bonnet)
Once bonnet open remove the bonnet lock mechanism, then with draw the lock barrel, shaft, coupling, By looking in side you will understand regarding the cross key
Anyway you need to remove one of the catches from the side of the plastic key This way it will fit back in to coupling.
Reassemble
This is a brief description But the cost to me was 45 minutes, £2 for a pack of plastic rivets / screws, and I cached my bumper with the chisel £5 for a touch up stick Total £7. Well worth the time and effort

Jun 25, 2008 | 2000 Ford Focus

Not finding what you are looking for?
1991 Nissan Pathfinder Logo

Related Topics:

35 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...