Question about 1985 Mitsubishi Starion

1 Answer

Replacement of cluth and pressure plate - 1985 Mitsubishi Starion

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 347 Answers

You have to remove the transmission/clutch housing from the engine.

Posted on Sep 24, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Clutch wont work pedal goes to floor and hear ratcheting sound


cluth plate and pressure plate bad,,,noise is more than likely loose clutch material scraping some part,,,how long since new parts installed?? not real expensieve,,but moderate amount of money., if you do it yourself. some have inspection plate you can see a little around flywheel housing,,to possibley survey damage. wipe finger in there and see how much material you get,,a lot,,,replace clutch and pressure plate

Jan 21, 2011 | 1983 Chevrolet S-10

1 Answer

My 2000 honda accord when i pres the cluth stay down , what is it


linkage.pressure plate worn through ,anything in fact ask a local mechanic to diagnose it for you

Jan 04, 2011 | 1991 Toyota Previa

1 Answer

Ford focus 2002 1.6 zetec se it was lacking power when accelerating with juddering and jerking i had a look on the site and was possible for clutch slipping ive since put new cluth on but still lacks power...


SOUND LIKE WEAK PRESSURE PLATE SPRINGS OR CONTAMINATED FLYWHEEL AND PRESSURE PLATE SURFACE HAS OIL ON IT..BESURE TO CLEAN FLYWHEEL AND PRESSURE PLATE MACHINE SURFACES WITH BRAKE PARTS CLEANER.

Apr 22, 2010 | 2004 Ford Focus

1 Answer

Idle up and down when Neutral


Hi
The clutch perssure plates seems worne off. you will have to replace them .
You can start by adjusting the clutch setting ...drive for a few days and if still problem persists then go in for a pressure plate change..
Regards
Berry

Feb 02, 2010 | 2000 Toyota Celica

1 Answer

Is it the tranny or the cluth:(?


youre going to need to replace your clutch set. purchase as a kit. it will come with the pressure plate, clutch disc, throw out bearing, pilot bearing/bushing, and an alignment tool. kit runs about $200.

Jan 10, 2010 | 1996 Pontiac Sunfire

2 Answers

Hyundai tucson 2 liter crdi gear box sound its a manual transmission


Hi there, the Common Rail Diesel Inyection (CRDI) 2000 cc 112 Hp M/T have a big trouble on cluth plate, and sounds very loud between 1500 and 2000 rpm on 2,3,4 shift.That motor has too much torque and cause excesive wear in the cluth roll and plate so starts roominess in the cluth system. You could change those parts but quickly the sounds come again. Hyundai is the resposable of that damage. I hope in the near future recall the CRDI model 112 Hp and replace the cluth.

Sep 20, 2009 | 2005 Hyundai Tucson

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

47 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

80417 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...