Question about 1992 Isuzu Pickup

Open Question

What is the torque setting and sequence for cylinder head bolts on a 1992 2.3l Isuzu pick up?what about reuse of new bolts that were installed?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 2 Answers

SOURCE: what is the 98 isuzu rodeo head bolt torque

joyce, there are different specs for sohc and dohc engines. my advice is to get a Haynes manual from the auto parts store.

doug

Posted on Sep 01, 2008

Ad
c17hydro
  • 2984 Answers

SOURCE: cylinder head torque settings 1990 2.6L isuzu motor

From front to back is this:


7 3 1 5 9



8 4 2 6 10



First torque value is 58 ft lbs.....then final torgue is 72 ft lbs.

Posted on Mar 21, 2009

dcramer531
  • 1654 Answers

SOURCE: I need the torque settings for the cylinder head

http://www.autozmagz.com/isuzu/2000-isuzu-trooper-s-torque-specifications/
try here and see if they can help. You can download manuals for free here.

Posted on Nov 23, 2010

  • 101 Answers

SOURCE: what is the cylinder head bolts torque specs for

ISUZU 2.3 137 4ZD1 86-95 43 FT/LBS 72 FT/LBS 58, 72 FT/LBS
ISUZU 2.3 137 4ZD1 85-87 43 FT/LBS 72 FT/LBS 58, 72 FT/LBS

http://www.aera.org/downloads/Torque3.pdf

Posted on Dec 25, 2010

  • 1 Answer

SOURCE: I am busy with an

timing marks

Posted on May 19, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the cylinder head torque settings for a isuzu kb250 2006


new bolt 21.7-36.1ft/lbs first step, 59.4-66.5ft/lbs second step
reused bolt 57.9-65.1ft/lbs first step, 72.4-79.6ft/lbs second step

Aug 05, 2014 | Isuzu Pickup Cars & Trucks

1 Answer

What is the cylinder head torque 3.8l


First off, these bolts are designed to stretch when they are installed; so do not reuse the original bolts; always use new.
With that in mind, the first torque setting is 37ftlbs make sure to use the correct sequence always working from the center out, and one side across to the other. Once all the bolts are set to 37, go through and tighten to 120ftlbs using the same sequence center and across working your way out. 110312gif_00000002576.gif

Jun 27, 2014 | 1985 Buick LeSabre

1 Answer

Cylinder head bolt tightening sequence for isuzu rodeo 1998


1998 Isuzu Truck Rodeo 2WD 2.2L MFI DOHC 4cyl

The Head Bolt Torque

Torque sequence ----------------- front ' 7 3 1 5 9 ' of ' ' engine ' 8 4 2 6 10 ' ----------------- Step 1: torque bolts in sequence to 18 Ft/Lbs Step 2: turn bolts in sequence an additional 90-degrees Step 3: turn bolts in sequence an additional 90-degrees Step 4: turn bolts in sequence an additional 90-degrees recheck final torque in sequence

1998 Isuzu Truck Rodeo 2WD 3.2L MFI DOHC 6cyl

The Head Bolt Torque

Torque sequence -------------- front ' 6 1 3 7 ' of ' ' engine ' 5 2 4 8 ' -------------- Step 1: torque to 20 Ft/Lbs Step 2: torque to 47 Ft/Lbs recheck final torque in sequence

Jan 15, 2013 | 1990 Isuzu Spacecab

1 Answer

Torque specs for 3.2 1995 heads on isuzu rodeo heads


0900c152800622a3.gif

To install:

  1. Install new camshaft seals and retaining plates onto the cylinder. Tighten the right camshaft seal retaining plate 6mm bolts to 65 inch lbs. Tighten the left camshaft seal retaining plate 8mm bolts to 191 inch lbs.
  2. Thoroughly clean the cylinder head and engine block sealing surfaces.
  3. Place a new head gasket on the engine block and carefully position the cylinder head on top of the new gasket.

Do not reuse or apply oil to the cylinder head bolts.
  1. Install new cylinder head bolts and torque them in sequence to 47 ft. lbs. (64 Nm) for the M11 bolts and 15 ft. lbs. (21 Nm) for the M8 bolts.
  2. Install the dipstick tube bracket to the cylinder head.
  3. Connect the front exhaust pipes to the exhaust manifolds. Tighten the exhaust bolts to 48 ft. lbs. (67 Nm).
  4. Install the power steering pump bracket. Torque the mounting bolts to 34 ft. lbs. (46 Nm).
  5. Install the cylinder head covers.
  6. Install the timing belt and the auto tensioner (pusher). Torque the mounting bolt to 14 ft. lbs. (19 Nm).
  7. Install the timing belt cover and oil cooler hoses and bracket.
  8. Install the crankshaft pulley. Torque the center bolt to 123 ft. lbs. (167 Nm).
  9. Install the fan pulley assembly.
  10. Install the power steering pump.
  11. Install the accessory drive belts.
  12. Install the engine coolant manifold and the heater hose.
  13. Install the intake manifold. Torque the nuts and bolts to 17 ft. lbs. (24 Nm) in a crisscross pattern.
  14. Install the fuel injector connectors and the fuel hoses to the fuel rail.
  15. Install the common chamber. Torque the nuts and bolts to 17 ft. lbs. (24 Nm).
  16. Install the EGR valve assembly. Torque the mounting bolts on the valve side to 69 inch lbs. (8 Nm) and the bolts on the exhaust side to 21 ft. lbs. (28 Nm).
  17. Connect the evaporative emission canister purge hose.
  18. Connect the fuel pressure control valve vacuum hose.
  19. Connect the positive crankcase ventilation hose.
  20. Install the throttle body assembly. Torque the mounting bolts to 14 ft. lbs. (19 Nm).
  21. Connect the vacuum hoses to the throttle body.
  22. Install the ignition control module and the spark plug wires.
  23. Connect the MAP sensor; Canister vacuum switching valve (VSV); Exhaust gas recirculation (VSV); Intake air temperature sensor and ground connectors.
  24. Connect the vacuum booster hose.
  25. Connect the air vacuum hose.
  26. Connect the accelerator cable. Adjust the accelerator cable by pulling the cable housing while closing the throttle valve and tightening the adjusting nut and screw cap by hand temporarily. Now loosen the adjusting nut by three turns and then tightening the screw cap. Make sure the throttle valve reaches the screw stop when the throttle is closed.
  27. Install the cooling fan assembly and the upper fan shroud.
  28. Install the air cleaner assembly.
  29. Connect the negative battery cable.
  30. Refill and bleed the cooling system.
  31. Refill and bleed the power steering pump if necessary.
  32. Refill the engine with fresh oil.
  33. Run the engine and check for leaks and proper compression.

May 16, 2011 | 1995 Isuzu Rodeo

1 Answer

Correct pressure for torque the head of mazda pickup 1998


Since you didn't say which engine you have, I've pulled torque specs for 3 different engines. Also, since I can't include a diagram showing the relative locations of the numbered head-bolt locations, it would be a good idea for you to purchase a vehicle specific repair guide that will show this info.


Take particular note about the TTY (Torque to Yield) bolts used on 2 of the 3 engines shown. It is said that new head bolts MUST BE USED when head is replaced or re-installed to obtain the proper torque.



B2500 4 Cylinder

Torque sequence: --------- ' 10 6 2 4 8 ' front ' ' ' 7 3 1 5 9 ' -----------Step 1: torque in sequence to 51 Ft/Lbs Step 2: torque again in sequence to 51 Ft/Lbs Step 3: final tighten all bolts an additional 90 to 100 degrees recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) that permanently stretch during the initial installation. New head bolts must be used when cylinder head is replaced or re-installed to obtain proper torque.







B3000 3.0 6 Cylinder

Torque sequence ---------- ' 6 4 2 8 ' ' ' ' 5 1 3 7 ' ---------- Step 1: torque to 59 Ft/Lbs Step 2: loosen in sequence (1) full turn Step 3: torque to 41 Ft/Lbs Step 4: torque to 73 Ft/Lbs









B4000 4.0 6 Cylinder

Torque sequence --------- ' 5 1 3 7 ' ' ' ' 6 4 2 8 ' --------- Step 1: torque cylinder head bolts in sequence to 26 Ft/Lbs Step 2: torque cylinder head bolts to 56 Ft/Lbs Step 3: turn cylinder head bolts in sequence an additional 90-degrees recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) that permanently stretch during the initial installation. New head bolts must be used when cylinder head is replaced or re-installed to obtain proper torque.


Good luck with this job!

Feb 06, 2011 | 1998 Mazda Pickup

2 Answers

What are the head torque specs?


1996 Isuzu Truck Hombre 2.2L SFI 4cyl

zjlimited_545.jpg

Fig.: Cylinder head bolt torque sequence-2.2L engine

Apply a coating of 1052080 or equivalent sealer to the cylinder head bolt threads. Install the cylinder head bolts (within 15 minutes of sealer application), then tighten them in the proper sequence first to a torque of 46 ft. lbs. (63 Nm) for long bolts or to 43 ft. lbs. (58 Nm) for short bolts and then tighten all bolts an additional 90 degree turn using a torque angle meter.

Hope this helps (remember to rate this answer).

Jan 25, 2011 | 1996 Isuzu Hombre

1 Answer

Want to know the amount of torque pressure do i use when tightening the head bolts, and whats the sequence?


To install:

0996b43f80208f65.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Cylinder head bolt torque sequence-3.8L engine

  1. Install the new cylinder head gasket with the arrow pointing to the front of the engine.
  2. Install the cylinder head.
  3. Install NEW cylinder head bolts. Torque the bolts in sequence, as follows:
    1. Step 1: 37 ft. lbs. (50 Nm).
    2. Step 2: Plus 120 degree turn.
To install:

0996b43f802316ea.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Tighten the cylinder head bolts using the following sequence-31L and 3.4L engines

  1. Install the cylinder head with a new gasket.
  2. Apply thread sealer to the head bolts.
  3. Tighten the cylinder head bolts to 37 ft. lbs. (50 Nm) plus an additional 90 degree turn.

Dec 16, 2010 | 2002 Pontiac Grand Prix

1 Answer

I need to find the torque specs for the connecting piston rod? also the sequence and torque for the cylinder head bolts this is for a kia rio 2004 6cyl


22 - 24 ft. lbs. for the rod caps and....
110795143Cylinder Head Tightening Torque and Sequence.

Tighten cylinder head bolts in order shown.
Tightening torque: 36.1 ft. lbs. (49 Nm, 5 kg-m)

Loosen bolts in reverse of order shown.

Retighten cylinder head bolts in order shown.
Tightening torque: 18 ft. lbs. (25 Nm, 2.5 kg-m)

Mark cylinder head bolts for rotational reference.
Rotate cylinder head bolts 90°(1/4 Turn) in order shown.

CAUTION:
  • Do not reuse the old cylinder head bolts.

May 31, 2010 | 2004 Kia Rio

1 Answer

Head bolt tourqe settings on a toyota cressida


Cylinder head bolt removal sequence


Removal sequence: Front 3 7 11 13 10 6 2 1 5 9 14 12 8 4

***CAUTION*** The above sequence must be followed during removal as to avoid warpage of the cylinder head unit

Reverse sequence to install, Step 1: Torque to 10 Ft/Lbs Step 2: Torque to 18 Ft/Lbs Step 3: Torque to 25 Ft/Lbs Step 4: Turn an additional 90 degrees Step 5: Turn an additional 90 degrees Step 6: Torque the 2 recessed 8mm bolts to 13 Ft/Lbs *** CAUTION *** engine uses Torque To Yield head bolts (TTY) that permanently stretch during the initial installation. New head bolts must be used when cylinder head is replaced or re-installed to obtain proper Torque

Don't forget to rate this answer, Good Luck

Apr 24, 2010 | 1992 Toyota Cressida

2 Answers

Need to know cylinder head bolt torque specs


Head Bolt Torque For your 1994 Oldsmobile Cutlass Supreme (3.4L SFI DOHC): clearpixel.gif Foot pounds (Final torque) clearpixel.gif Note: Torque sequence --------- | 6 2 3 7 | | 5 1 4 8 | --------- Step 1: torque in sequence to 33 Ft/Lbs Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque. clearpixel.gif clearpixel.gif clearpixel.gif Foot pounds (Final torque) clearpixel.gif Note: Torque sequence --------- | 8 4 1 5 | | 7 3 2 6 | front --------- of engine | 6 2 3 7 | | 5 1 4 8 | Step 1: torque to 40 Ft/Lbs --------- Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque.

Feb 07, 2009 | 1994 Oldsmobile Cutlass Supreme

Not finding what you are looking for?
1992 Isuzu Pickup Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14384 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...