Question about 2009 Audi Q7

1 Answer

Car will not start, key unable to be removed from ignition

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Governor:

    An expert whose answer got voted for 20 times.

  • Contributor
  • 164 Answers

Sounds like a bad switch... check your fuses first.

Posted on Sep 11, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

After replacing my battery, I am unable to start the car without hitting the alarm reset under the dash. A mechanic told me to turn the key up to crank, quicfkly 5 times to reset. That did not work.


PLACE THE PROGRAMMED KEY IN THE IGNITION SWITCH. FOR THE FIRST KEY. TURN IGNITION SWITCH ON AND WAIT 3 SECONDS RETURN TO OFF POSITION AND REMOVE KEY. FIRST AND SECOND PROGRAMMED KEY OPERATIONS MUST BE PERFORMED WITH IN 15 SECONDS. INSERT SECOND PROGRAMMED KEY AND SWITCH IGNITION ON. WAIT APPROXIMATELY 10 SECONDS. ENSURE IMMOBILIZER WARNING LAMP BEGINS TO FLASH AND AN ACOUSTIC SIGNAL IS EMITTED.SWITCH IGNITION OFF AND REMOVE KEY.WITHIN 50 SECONDS INSERT NEW KEY AND SWITCH IGNITION ON.WAIT APPROXIMATELY 10 SECONDS.ENSURE ACOUSTIC SIGNAL IS EMITTED AND IMMOBILIZER WARNING LAMP REMAINS ILLUMINATED FOR 3 SECONDS INDICATING PROGRAMMING COMPLETE. FOR EACH ADDITIONAL KEY REPEAT PROCEDURE STARTING FROM THE BEGINNING.REPLACEMENT KEYS CAN ALSO BE REPROGRAMMRF USING DIAGNOSTIC EQUIPMENT.MAXIMUM 8 KEYS CAN BE REPROGRAMMED.

May 21, 2011 | 2005 Chrysler Sebring Conv

2 Answers

Broken key in ignition lock on a Kia Shuma 2000


can you use pin-nose pliers to grasp the key or a Popsicle stick with an adhesive to stick to the broken key and remove that way

Sep 21, 2009 | 1999 Mercury Cougar

2 Answers

1998 Disco-Unable to remove key from ignition.


If disco is automatic move the transfer lever from high to low box and back again firmly then the key will come out there is a safety feature on the autos to prevent the key being removed if the transfer box is not in either high or low correctly with most dicso;s the transfer shift lever is stiff. through lack of use .once it is pushed in properly the key will release it works every time and I have had four v8 autos
basically you cant remove the key because even though the gearbox is in park if the transfer gears are not fully home the park sensor on the gearbox thinks it is out of gear eg not in park so wont let you remove the key and leave the car out of gear in case it rolls away .Dan

Jun 30, 2009 | 1998 Land Rover Discovery

1 Answer

1996 Cavalier ignition switch will not start car.


you apparently have the link either disconnected or bound up at the key end, it may even be disconnect or out of place. If you loosened our outherwise move the lower end switch tou may be able to realighn what is out of whack Good Luck-Ned

Jun 16, 2009 | 1996 Chevrolet Cavalier

1 Answer

2002 Pontiac Grand prix wont start; unable to remove key


On many cars, if the battery is dead, it locks the key in the ignition. Put a battery charger on the car or replace the battery and give it a shot.

Good luck.

May 15, 2009 | 2002 Pontiac Grand Prix

3 Answers

2002 Nissan pathfinder will turn over but will not start.


There really shouldn't be anything else that needs to be done, unless there was a gear inside the ignition cylinder that wasn't installed in the proper position, this will cause the ignition to only go to a certain spot when turned and it may not be fully engaging the start position, i would re-check the installation of the new ignition assembly.

Mar 16, 2009 | 2002 Nissan Pathfinder

1 Answer

Ignition


See Procedure for REPLACEMENT.

1. Disconnect the negative (-) battery terminal. 2. Remove the crash pad side cover (A).4862483.gif 3. Remove the ignition switch (A) after loosening the screw and disconnecting the 6P connector.e5d4d9c.gif 4. Remove the steering column shaft (Refer to the ST group). 5. Remove the key warning switch and key illumination lamp (A) after loosening the screws and disconnecting the 6P connector.1ceff53.gif 6. If it is necessary to remove the key lock cylinder (A), Remove the key lock cylinder (A) after pushing lock pin (B) with key ON.5d997e5.gif 7. Installation is the reverse of removal procedure

Jun 14, 2008 | 2007 Hyundai Sonata Limited Sedan

Not finding what you are looking for?
2009 Audi Q7 Logo

Related Topics:

47 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audi Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

75005 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14195 Answers

Are you an Audi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...