Question about 2002 Audi A4

1 Answer

Replacing Camshaft Position Sensor Guide audi a4

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Governor:

    An expert whose answer got voted for 20 times.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 5 Answers

The camshaft position sensor is located behind timing belt cover in front of engine.Remove cover, sensor is visable in top right hand corner.Unplug, remove 2 10mm bolts.Reinstall,plug back up,reinstall cover,crank engine.

Posted on Sep 13, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2001 audi a4 quatro 2.8l DOHC check engine light is flashing and my scanner gave the fault code p0305 and a pending code p1340 . What should I do tofix the problem?


p 0305 is misfire on no 5 cylinder code p1340 refers to camshaft (CMP) sensor 1 bank/ crankshaft position (CKP) sensor ---out of sequence === causes ---valve timing--CMP/CKP sensor installation---CKP sensor rotor
misfires are more injector problems that plugs
take it to an authorized service center for the position senor and valve timing problems

Dec 12, 2016 | Audi Cars & Trucks

1 Answer

Engine misfaire


Check your fuel injector.

Dec 12, 2013 | 2003 Audi A4 3.0

1 Answer

Camshaft position sensor bank 1


Bank one is passenger side cylinder bank.
Cam sensor should be at front of cylinder head.

Nov 08, 2013 | 2002 Audi A4

1 Answer

If one camshaft position sensor in bad, should all four be replaced? I have an Audi 2003 A4 wagon . With faulty sensors, what problems would you normally experience with the car? Thanks, Thomas


With these it can and usually will, effect timing and acceleration. No you do not need to replace all 4. Replace the bad one, clear the code and go for a good long test drive.

Dec 09, 2010 | 2002 Audi A4

1 Answer

Got audi a4 1996 diesel need to change cambelt but


A diesel uses a different procedure. You'll need a tool to hold the camshaft pulley parallel to the top of the cylinder head. The timing mark to set TDC for piston #1 is located on top of bell housing. The pointer must be aligned on the diamond cut on the flywheel. A VW/Audi setting bar tool #2065A is needed to lock the camshaft in position. Lock the injection pumpin position using the special lock pin (VW/Audi special tool no. 2064). Caution: If the drive belt is broken or has jumped time, do not attempt to lock the sprocket at this time!!! You will also need VW/Audi special tool no. VW210 to measure belt tension between camshaft sproket and injection pump sprocket. So good luck.

May 01, 2010 | 1996 Audi A4

1 Answer

Surging at low revs and shuddering on take off occasionally audi 3lt a4 b6 multitronic


Common low RPM problem occurs identically many other manufacturers ***/American/German vehicles due to camshaft position sensor:

Easily and cheaply fixed by replacing cam position sensors.

Feb 15, 2010 | 2002 Audi A4

2 Answers

What is a cam crank sensor on 2004 Audi A4


The "cam crank" sensor is the "reader" for position and speed of the camshaft. This sensor send informations to Engine Control Unit about camshaft position and speed. If the sensor is faulty engine stops!

Oct 23, 2009 | 2004 Audi A4

3 Answers

Cam position sensor error.


Needs to be reset with a scan tool.

Sep 17, 2009 | 2004 Audi A4

3 Answers

Camshaft position sensor replacement for 2002 Audi A4


its not hard to fix.but you going to have to move some things to get to it. you will need a haynes repair manual.it will show you photos and instructions how to replace it.

Jul 05, 2009 | Audi A6 Cars & Trucks

Not finding what you are looking for?
2002 Audi A4 Logo

3,507 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audi Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

76164 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14363 Answers

Are you an Audi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...