Question about 2004 Toyota 4Runner

1 Answer

How do i replace rotors on a 4runner

How do i replace front rotors on a 2004 toyota 4runner

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.

    Vice President:

    An expert whose answer gotĀ voted for 100 times.


    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

  • Expert
  • 73 Answers

Remove the 2 bolts holding the front caliper on then just remove the rotor

Posted on Sep 13, 2009

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How to replace blinker light bulb on 2004 toyota 4runner?

is it front or rear blinker if is rear you will have to open the hatch take out the screws and the front you might have to reach under the bumper

May 29, 2014 | 2004 Toyota 4Runner

1 Answer

My brake pedal is hard after replacing the front pads. 1990 4runner

Hard how?

You machined or replaced the rotors
You removed all rust on hub & rotor mounting surfaces
You removed all rust from caliper & pad sliding surfaces
& lubed with anti-seize
You flushed all four corners (every 2 years) brake fluid
You bought the best pads out there (raybestos,wagner,etc)
You have no vacuum leaks at the booster & pedal holds until
the engine is started?

Sep 22, 2011 | 1995 Toyota 4Runner

1 Answer

What tools are needed to change the front brake pads on a 2004 Toyota 4Runner

you will need a couple of screw drivers to push pistons back in and a pair of pliers to remove clips off pins holding pads and a small long punch to tap pins out, then clean top and bottm of caliper where pads sit, use small steel brush.the first thing i do is get a screw driver inbetween pad and rotor and pry pistons back slowly then the same for the outer pistons, then remove pins and pads, hope this helps, note; caliper does not need to be removed.

Aug 27, 2010 | 2004 Toyota 4Runner

2 Answers

Front end wobbles after highway speeds and brakes/bearings are hot. Very pronounced when braking after a few minutes at highway speed. Had original rotors turned. Helped, but then had them replaced with...

I have had the same problem ever since I bought my 4runner new in 99. I've tried all kinds of tires, constant balancing, rotations, alignments, brakes, you name it, I even have a new front end now, but still have wobble in the front end. It's acts like having loose tie-rod. NoOne can figure it out. LEMON?

Jul 15, 2010 | 1999 Toyota 4Runner

1 Answer

I have a toyota 1999 4runner This car started to trumble when I drove and pushed the breaks.

You need to do some front brake work. They need to come apart at least once a year, to remove rust,lube and check rotor condition.

Mar 10, 2010 | 1999 Toyota 4Runner

1 Answer

Do the rotors have to be replaced when replacing front brake pads

No they don't. If the feel smooth, then just change pads, if they are slightly scortched and feel slightly ruff, just have them turned.

Jan 30, 2010 | 2004 Toyota 4Runner

1 Answer

How do I get rotors off front of 87 4Runner?

From memory, to remove the front disc rotors, the hub has to be disassembled completely from the vehicle. The rotors bolt to the hub from behind. Start by removing the calipers, then start disassembling the free wheel hubs, bearings etc.

Jul 19, 2009 | 1987 Toyota 4Runner

1 Answer

Front brake rotors 1995 toyota 4runner

If you have 6 bolts going around the center (manual lock in/lock out) hub, you are going to be there a while. The center hub needs to come off, and ALL of the internal wheel bearings need to come out. The whole locking hub must be removed in order get the rotor off. This is NOT an easy job, and you need a special tool to loosen/tightem the wheel bearings. Figure 2 hrs per side if you have all of the proper tools & skill level.

Sep 27, 2008 | 1995 Toyota 4Runner

Not finding what you are looking for?
2004 Toyota 4Runner Logo

Related Topics:

337 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts


Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides