Question about 2005 Chrysler Pacifica

1 Answer

The serpentine belt on my 2005 Pacifica with a 3.5 liter engine has broken. There is no diagram under the hood. Where can I access a diagram for routing the replacement? Thank you.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 122 Answers

Possibly if you go to autozone.com, there is a area at the bottom of the page refering to manuals. you will have to join with an e-mail address and create a user profile. the cost is 0. after you create your profile, select your vehicle and look up in the free online repair manual. I hope this helps, good luck!

Posted on Sep 11, 2009

Testimonial: "Your advice was helpful. I found out that autozone does not have an online manual for a 2005 Pacifica. Thanks for trying."

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Serpentine belt diagram for a 2003 Chevy unpalatable 4.3


Pop the hood of the car and locate the serpentine belt routing diagram. The diagram on the 2003 Chevrolet Impala is on top of the fan shroud. The diagram will be a picture of all of the accessory pulleys and how the serpentine belt is routed among the pulleys. This diagram will give you the exact direction for routing the new belt onto the pulleys. If you cannot find a serpentine belt routing diagram, take a notepad and pen and draw out the exact routing diagram of the old belt across the pulleys.

  • 2 Locate the serpentine belt tensioner. It is located below the alternator on the left front side of the engine. The tensioner on the 3.4 liter, 3.5 liter and the 3.9 liter engines will require a 3/8 ratchet to release the belt tensioner. The 3.8 liter engine will require a ratchet and a 15 mm socket for the belt tensioner. Rotate the belt tensioner clockwise to loosen and remove the belt from the belt tensioner pulley.
  • 3 Slide the old belt from the belt tensioner pulley. Remove the belt from the remaining pulleys and pull the belt from the engine compartment.
  • 4 Route the new belt across the crankshaft pulley first. The crankshaft pulley is the big pulley on the bottom of the engine in the center. Then route the serpentine belt across the remaining pulleys as directed by the serpentine belt routing diagram. Leave the belt tensioner pulley for last.
  • 5 Rotate the belt tensioner clockwise again to relieve the tension and slide the new belt across the top of the belt tensioner pulley. Release the belt tensioner and the belt will tighten up as the tensioner applies pressure to the belt. Make sure the new belt is properly seated in all the pulleys.
  • 6 Crank the engine and inspect the belt again to make sure that it stays seated in the pulleys.

  • Read more: How to Replace a Serpentine Belt on a 2003 Chevrolet Impala ' eHow.co.uk http://www.ehow.co.uk/how_6120665_replace-belt-2003-chevrolet-impala.html#ixzz1Yi6QLAjb

    Sep 21, 2011 | 2003 Chevrolet Impala

    2 Answers

    I need the serpentine belt diagram for a 3.8 2003 Impala.


    There should be a diagram of the belt routing under the hood somewhere. clay58_53.png

    Jul 03, 2011 | 2006 Chevrolet Impala

    1 Answer

    I need a diagram for a serpentine belt 3.8 engine


    Hi kimberly_40

    here is the belt layout for your 2005 Chrysler Pacifica


    FIG : Accessory drive beltrouting: -3.5L engin b> (1) Alternator (2) Automatic Tensioner (3) P/S Pump (4) Idler Pulley (5) A/C Compressor (6) Crankshaft Pulley

    imbmetz1_5.gif
    let me know if you need anything else

    Bill
    EX f31817b.gif

    Standing Member of G.O.T.
    imbmetz1_3.gif

    Feb 19, 2011 | 2005 Chrysler Pacifica

    1 Answer

    Replace serpentine belt on a jeep grand cher w/4.7 liter engine


    It's posted inside the hood. Lift hood, look on passenger side.

    Nov 16, 2009 | 2000 Jeep Grand Cherokee

    2 Answers

    Need a diagram for a serpentine belt on a 2005 impala, 3.8


    Below is the diagram you requested. Best of luck on your repair.
    Greg
    43c72e0.jpg

    Nov 04, 2009 | 2005 Chevrolet Impala

    Not finding what you are looking for?
    2005 Chrysler Pacifica Logo

    1,642 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Chrysler Experts

    yadayada
    yadayada

    Level 3 Expert

    77499 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22306 Answers

    chargerhp
    chargerhp

    Level 3 Expert

    814 Answers

    Are you a Chrysler Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...