Question about 1994 Ford Bronco

1 Answer

1994 Ford Bronco steering wheel puller Steering Wheel Puller T67L-3600-A, is that a standard wheel puller or one similar for removing a yoke flange off a differential?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 631 Answers

You should be able to use a standard steering wheel puller and no they are different from flange puller.

Posted on Sep 11, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need To replace my ignition switch on my 86 Ford Bronco V8/4WD.


disasemble steering column, torc screw behide turning signal switch. Must have steering wheel puller and lock puller for this job

Sep 09, 2017 | Ford Cars & Trucks

Tip

Chevrolet Truck Steering Wheel Removal Instruction


1 Turn the steering wheel from side to side until it locks into place. This will make the process a bit easier, as the wheel won't be turning as you work.<br /><br />2 Remove the horn button in the center of the steering wheel by pulling it off towards you. This will expose the steering wheel nut at the center.<br /><br />3 Unbolt the center bolt from the steering wheel, using the 1/2-inch ratchet, extension and socket. This might free the steering wheel right away, but most likely you'll have to proceed to the next step.<br /><br />4 Position the steering wheel puller on the steering wheel such that the center bolt on the puller is on the center shaft of the wheel. Then thread in the bolts supplied with the puller into the two threaded holes on either side of the center shaft on the wheel.<br /><br />5 Tighten down the center bolt on the steering wheel puller using the 1/2-inch ratchet and socket until the steering wheel pops free. Then remove the steering wheel puller from the steering wheel.

on May 28, 2011 | Chevrolet 1500 Cars & Trucks

1 Answer

How do I remove a steering wheel off my 1964 Ford Thunderbird


Remove the center horn pad assembly and remove nut holding steering wheel to column. You need a steering wheel puller to remove it from the tapered shaft once the nut is loose. You can rock the steering wheel and pull if you don't have a puller but when it lets go watch for a broken nose.

Apr 12, 2015 | Ford Thunderbird Cars & Trucks

1 Answer

How do i pull the steering wheel on 2008 ford escape?


Remove the airbag/horn button. Unscrew that big nut in there. Attach a steering wheel puller to the wheel, mark the wheel's position, and crank the wheel off the stem. DO NOT disturb the steering until the wheel is back on, and be careful to align the wheel the same way going on as it was in when it came off.

It's really pretty easy to remove, but it DOES take that puller. The pullers are cheap.

Aug 07, 2014 | 2008 Ford Escape

1 Answer

How do you remove the steering wheel. It has a bolt to hold it, not a not to remove?


You will need a steering wheel puller. Once you remove the center bolt you will thread bolts through the puller into the two small holes on each side of the center hole, then the puller has a jack shaft that pushes against the center shaft where the bolt was.

Jul 26, 2014 | 1994 Ford Escort

1 Answer

How do I replace a turn signal switch on a 1989 Full Size Bronco, not a tilt wheel.


You will need to remove the steering wheel...using a steering wheel puller, or a harmonic balancer puller...the turn signal switch is under the steering wheel...unscrew hold downs, trace wire from turn signal switch to under the dash behind the brake pedal, disconnect the connector wire...re-install pulling wire up from floor to inside the steering wheel...sometimes tying the wire to another object, then pull through...hope this helps.

Oct 11, 2013 | 1989 Ford Bronco

4 Answers

Can not take off the steering wheel on my 2004 e350 van, the puller i rented w the tabs (the screw bolts do not work) are just taking chunks out of the steering wheel. what can i do?


I think you have the wrong puller. The screws are not the right size. There are usually several sets
of screws with the steering wheel puller. Are you sure you are using the correct screws?

There are usually 2 sets of screws with the puller that are the same size, but have different
number of threads per inch. So check to make sure you are using the right screws with the puller.

Where did you rent the puller?

Oct 02, 2011 | 2004 Ford E Series

1 Answer

How to take off a steering wheel


Hi Lisa,
Remove the center cover/horen button,Remove steering wheel retaining nut or bolt then install steering wheel puller and press steering wheel off by tightening puller bolt. Hope this helps Lisa, Have a great day!

Sep 08, 2010 | Ford Ranger Cars & Trucks

1 Answer

NEED TO TAKE STEERING WHEEL OFF 1981 FORD BRONCO WITH COLUMN SHHIFT how?


I have worked on this same problem on a 1985 F100 and I'm sure the steering system is very similar. Take off all the pretty stuff on the outside of the steering wheel (horn buttons or horn ring) then you should be faced with a 11/16th to 3/4th nut. remove that nut and get a steering wheel puller (you can rent those at most auto parts houses for about $20.00. there is no replacement for having the right tool for the right job!) There will be holes that the steering wheel for the puller to be put in to. After you attach the puller to the wheel, take the middle bolt on the puller and tighten it until it makes contact with the bold on the steering column that you took the nut off of. You might have to hold the puller while you tighten the puller. After it makes contact, keep tightening until you feel the steering wheel POP off. Please resist the urge to try and use a hammer to take the steering wheel off and not use a steering wheel puller because it will never work (don't ask me how I know this!)

I hope this helps and much good luck!

Dec 18, 2008 | 1981 Ford Bronco

Not finding what you are looking for?
1994 Ford Bronco Logo

Related Topics:

142 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...