Question about 2001 Ford Super Duty F 450

1 Answer

Head lights when I turn the lights on they come off when I push forward on the turn signal to go to brights I loose all head lamps but all running lights stay on.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 8,619 Answers

Hi

You need to open the fusebox located under the dashboard and then check all the fuses. If the fuses are all fine, then check for burned/broken wires.

Please do accept the solution if the issue is resolved or else revert for further assistance.

Thanks
Rylee

Posted on Sep 11, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 1993 chevy cheyenne k1500 turn signals and parking lamps don't work, but the head lights do. When ever I turn on the hazard lights they work then but other than that, no.


Most likely its your turn signal switch. For some reason GM decided to run all the lights except headlights through it. You most likely don't have brakelights either. Sometimes you can verify by pushing a little forward or backwards pressure on the hazard switch and everything will start working.

Apr 15, 2016 | Cars & Trucks

1 Answer

Passenger side turn signal flashes faster but dont work even at day runing light, comes on when head lights are on, replace bulb and socket because was melted but stilldoes the same


Turn Signal Lamps
The turn signal lamps may only be activated with the ignition switch in RUN or BULB TEST position. The T/SIG fuse supplies ignition voltage to the turn signal switch. When the turn signal switch is placed in either the left or right position, the turn signal switch sends an ignition voltage to the hazard lamp/turn signal flasher, which sends an on-off signal to the turn signal switch. When the turn signal switch receives the on-off signal it will send that signal to the following lamps on the LH or RH side:
?€¢
The Rear Turn Lamp


?€¢
The Turn Signal Indicator


?€¢
The Sidemarker Lamp


?€¢
The Sideview Mirror (Pontiac Thunder only)

The turn signal switch also sends a separate on-off signal to the Daytime Running Lamps (DRL) control module, which relays the signal to the appropriate front turn signal. The front turn signals are grounded at G101 and G102. The rear turn signals are grounded at G401. The sidemarker lamps are grounded through the corresponding front parklamp.
The sideview mirror turn signals are a bank of LEDs placed behind the mirror glass.
The hazard lamps operate on battery voltage. The HAZARD fuse supplies battery voltage to the turn signal switch. When the hazard switch is pressed, the turn signal switch sends battery voltage to the hazard lamp/turn signal flasher, which sends an on-off signal to the turn signal switch. The turn signal switch send the on-off signal to all the turn signal lamps, causing all the lamps to flash including both IPC turn signal indicators. The hazard lamp/turn signal flasher is grounded at G200.
When the parklamps are ON, the sidemarker lamps receive voltage from the park lamp supply voltage circuit and illuminate. The sidemarker lamp is grounded through the corresponding rear turn signal. When the turn signal switch is place in the left or right hand position, the rear turn signal illuminates and the sidemarker lamp will loose its ground, causing the sidemarker lamp to turn off when the turn signals are on and to illuminate again when the turn signal is off.
Which blub an socket did you replace ? check the other blub ? The switch and or the flasher module can cause this problem .
Replace the turn signal switch. Refer to Multifunction, Turn Signal, and Hazard Switch Replacement - On Vehicle in Steering Wheel and Column.
Did you complete the replacement?

Which

Oct 11, 2015 | 2001 Pontiac Montana

2 Answers

Regular headlights will not come on, only brights


There is a head lamp driver module for low beams, I can't tell if module is faulty? Check voltage and ground for module. Can you check applicable trouble codes? The BCM does have some control on that module, pulse/width modulated ground. Some of the national brand autostores will check codes for free.

Note the wiring.
25432079-f354phfyjkegikfzmbtgakwh-1-0.jpg

Feb 15, 2015 | 2008 Chevrolet Trailblazer

1 Answer

1994 Ford ranger why would head lights not work


Common problem.
T/S lever is part of the "multifunction switch" that controls hi/lo lamps. It can be replaced by removing the lower shroud (3 or 4
screws from the bottom up). SW1093 @ Auto Zone about $66.

Jan 07, 2015 | 1994 Ford Ranger Supercab

2 Answers

All my gauges and even speedometer and odometer have stopped working on my 2001 crown victoria. Any advise? The kick panel above the brake pedal is loose and every now and then if I push up on the loose...


If you can kick the panel and it work, then there is a loose connection somewhere. Start at the fuse block and make sure you have a good connection there, then move forward.

May 26, 2011 | 2001 Ford Crown Victoria

1 Answer

Honda 2005 CRV - The left headlight is OK. The turn signal works both sides till I turn on the headlights. Then the right one does not work. that is a Honda safety feature. Non working turn signal on full...


Bypass head light switch and see what you get. Three items can cause your problem . The head light switch, flasher relay , shorts in circuit. I would go with switch.

Aug 18, 2010 | 2005 Honda CR-V

2 Answers

Bright lights pop on when car is parked


you need to replace the turn signal switch,its loose and making contact when it should not,,causing the headlamps to come on,replace the switch,,like $50 for the new part,not too hard to install

Oct 06, 2009 | 2002 Saturn L-Series

1 Answer

No driving lights?


Hello there - I would suggest checking the fuse for your lights in the fuse box, and check under the hood for a fuse/relay box, and have the relay tested. If the fuses and relays are good, open the hood, and try to check the connection to the headlights and make sure they are securely connected. You also mentioned that when you push the headlights switch forward for brights, and turn on the night time head lights, and neither come on but the daytime lights do, makes me suspect the switch itself may be bad. I would first check the fuses and relays if any. Second, I would replace the bulbs (if replacable). Other than that, my last guess would be an electrical problem in the wiring somewhere. I hope this information helps you fix your lights. Thank you for your time and consideration in my suggestions/answers.

Apr 01, 2009 | 1996 Mazda 626

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5516 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...