Question about 1996 Ford Crown Victoria

1 Answer

How to take out the back seat backrest - 1996 Ford Crown Victoria

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 83 Answers

Push down on the rear of the seats part of the backseat and it should release and pop loose. Remove it.

Then there are two bolts at the bottom of the seat back, remove these and it should come out easily

Posted on Sep 10, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Ford 2008 expedition, power drivers seat won't recline, but everything else works.


Power Recliner
The driver seat has an electro-mechanical backrest adjuster. The backrest adjustment switch is located on the side of the seat cushion side shield and is part of the seat control switch. The recliner motor is mounted to the backrest frame. Power recliners and motors are only serviceable by installing a new backrest frame assembly.
Does yours have Driver and Passenger Power Seats Without Memory Or Power Driver Seat With Memory ?

B1666 Seat Driver Recline Motor Stalled On-Demand If the motor does not operate, Go To Pinpoint Test L . If motor operates, Go To Pinpoint Test M . Take it an have it check !
Does your

May 15, 2016 | Ford Cars & Trucks

1 Answer

Remove rear seat


Rear seat cushion-fold forwards,release plastic clip from hinge,remove wiring multiplug if applicable.Lift out cushion.(40% backrest)Tilt forward approx 20degrees,use a screwdriver to release catch retainer on outer pivot pin.lift backrest and withdraw from inner pivot pin.Lift the backrest from inside vehicle.(will only lift out if backrest is tilted forward 20degrees from verticle. 60% section can then be removed on saloons by releasing the lock with a finger and pulling from the anchor pins.On estates unscrew centre seat belt lower mounting and unscrew hinge pin from centre support. unhook upholstery clip and lift backrest from lefthand side mounting.slide backrest towards the door to release centre pinlug and withdraw backrest from inside the vehicle. Refit in reverse order.

May 22, 2015 | 1999 Saab 9-5

1 Answer

How do I Bend forward the back of the rear seats of a Nissan Pulsar 2014 to put the seat covers on?


Do not bend the rear seat back rests, they will never be the same again. On most (if not all) cars the rear backrests are bolted on by means of two bolts behind the seat, so first remove the seat (the bottom padding that keeps your backside from hitting the floor) by pulling the seat up. On some vehicles, the seat is bolted down with two 6mm bolts on either side. Once you have the seat out, you should see two bolts holding the back rest to the body of the car. Undo these, and the backrest comes off easily.
Now fit the seat covers and bolt the backrest back into place. It is not a difficult job, shouldn't take more than an hour or less.

Dec 14, 2014 | Nissan Cars & Trucks

1 Answer

How do you remove the back seat in a 2005 Toyota Avalon?


Most back seats come out the same way. The seat (bottom part) is usually bolted down with two bolts that can be accessed by lifting the rear carpet away from the seat sill, near the floor. Once these bolts have been removed, the seat can be lifted up and out. This should now reveal the two bolts that hold the backrest to the body. Undo them and the backrest can be pushed up and out.

Sep 30, 2014 | 2005 Toyota Avalon

1 Answer

I locked my only set of keys in the boot of my audi a4 2004. how do i go about getting them out? can i take the back seat out and where do i start?


Yes, you can remove the back seat and access the trunk from car inside. The rear seat is split 60/40 and folds down for carrying even more stuff. Push the backrest upper lateral button and fold down the rear seat backrest. Then go into the trunk and take your set of keys.

Mar 28, 2011 | Audi A4 Cars & Trucks

1 Answer

Haw to gat out seat back


Rear Seat Backrest-SuperCab Removal
  1. Fold down both rear seat cushions.
  1. Remove the rear seat back.
    1. Push the wire hooks rearward to disengage the seat backrest from the back panel of the cab.
    1. Lift the rear seat back upward and remove.
    a0015238.gif
Installation
  1. Align the upper hooks with the upper brackets on the back panel of the cab.
  1. NOTE: Make sure the safety belt webbing is not twisted.
    Route the rear center safety belt through the retainer ******** the rear seat back.
  1. Place the lower hooks behind the lower brackets on the back panel of the cab.
  1. Lower the seat back until the lower hooks engage the lower brackets.
  1. Verify all three upper hooks have engaged the upper brackets

Feb 12, 2011 | 2005 Ford F-150

1 Answer

How do I remove the back seat / backrest from a bmw 328IC 1997


Remove the headrests (if equipped). Grip the lower seat at the front part of the seat and pull upwards to clear the clips(1), and the remove the lower seat.
Fold down the armrest and remove the bolts behind the armrest. The upper seat(backrest) is then pushed up, pulled forward and then moved either left or right out of the vehicle from behind the seatbelts.


suzman_15.jpg

Nov 15, 2010 | 1997 BMW 328

1 Answer

Middel seatbelt will not loosen


I think you have to remove headrst bfore folding seat back down. You may have to unbolt seat from floor. 4 bolts.
Rear Seat Backrest —Split Bench Removal
NOTE: The 40% rear seat backrest must be removed before the 60% rear seat backrest.
40% rear seat backrest
  1. Remove the 40% rear seat backrest.
    1. Remove the nuts and bolts.
    1. Remove the backrest.
60% rear seat backrest
  1. Remove the 60% rear seat backrest.
    1. Remove the nut and bolt.
    1. Remove the backrest.
Installation
NOTE: The 60% rear seat backrest must be installed before the 40% rear seat backrest.
60% rear seat backrest
  1. NOTE: Do not tighten the nut and bolt at this time.
    Install the 60% rear seat backrest.
    1. Install the rear seat backrest.
    1. Install the nut and bolt.
40% rear seat backrest
  1. NOTE: Do not tighten the nuts and bolts at this time.
    Install the 40% rear seat backrest.
    1. Install the rear seat backrest.
    1. Install the nuts and bolts.
60/40% rear seat backrest
  1. Tighten the 60/40% rear seat backrest nuts and bolts in the sequence shown.
de01dcf.gif
40% Rear Seat Backrest
  1. Tighten the 40% rear seat backrest nuts and bolts in the sequence shown.

Jun 11, 2009 | 2005 Ford Escape

2 Answers

Hai i would like to know how to fold the back car seat to increase cargo space in hyundai santa fe 2003


The rear seats have a pull strap located between the bottom cushion and the backrest of the rear seats used to disengage a lock to lift up the bottom cushion. The pull straps will only stick out an inch or so, or they might have fallen down between the seats and then you wont see them. Before you can lower the backrest of the rear seats, the bottom cushions have to be lifted up and forward out of the way so that the backrest may lie down flat. If your pull straps are not visible between the bottom cushion and the backrest, you may have to stick your hand between the cushions and feel for the straps. Once you find the straps, pull upward on the while lifting on the bottom cushion where the pull strap is located and the seat should tilt forward. Once you have manged to do this, the lever for the backrest is located on the top of the backrest. Just slide the lever and tilt the backrest to the desired position.

Apr 13, 2009 | 2003 Hyundai Santa Fe

1 Answer

How to fold down back seat


There should be a loop between the seat and backrest, pull that and the seat will pull toward the front seats. After that, pull the lever located at the outside of the backrest. This lever is on the outside of the seat by the door-side of the seat. Pull that up and allow the backrest will fold down and the headrest will pivot back and your seat is folded down.

Jun 28, 2008 | 2004 GMC Envoy

Not finding what you are looking for?
1996 Ford Crown Victoria Logo

Related Topics:

180 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...