Question about 2004 Chrysler Sebring

1 Answer

Worn rear wheel bearing, 2004 chrysler sebring, non a.b.s.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Chrysler Master
  • 412 Answers

REMOVE THE REAR DRUM OR ROTOR,REMOVE DUST CAP FROM BEARING..REMOVE RETAINING NUT..HUB/BEARING WILL SLIDE OFF SPINDLE..REVERSE PROCEDURE TO INSTALL..I HOPE THIS HELPS

Posted on Sep 14, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2004 Chrysler Sebring has been sitting since March amd now the rear drivers side tire is locked up


Rusted brakes. Sometimes, you can hit the wheel/drum with a hammer and get it to break loose. You NEED to replace the brakes! Possibly the drum also

Sep 13, 2016 | 2004 Chrysler Sebring

1 Answer

Find the filler plug for a 2004 chrysler sebring front differrential


The Sebring is a front wheel drive car. The transmission drives the two axles directly. You only need to check your transmission fluid. There is no differential like a rear axle style unit.

Jan 13, 2015 | 2004 Chrysler Sebring

1 Answer

Thumping noise when hit bump in 2005 Chrysler Sebring on rear passenger side


shock absorber hitting the 'bump stop' , means shocker is weak and needs replacing, loose/worn ball joint , worn wheel bearing , one of these

Jul 16, 2014 | Cars & Trucks

1 Answer

I need toe-in, caber and caster for a Chrysler Sebring Cab 2004


It's toe-in, caster, & camber--all included in a front wheel alignment at an alignment shop--make sure your struts, link rubbers, ball joints, wheel bearings, & tie-rod ends are good first or they will tell you to replace them before alignment(or they should be replaced if worn). An alignment can cost from $35-$100--depending on whether you get a 2 or 4 wheel alignment. Usually the rear is okay--unless the car has been in an accident or has over 200,000 kms.(120,000 miles) on it.

Jan 21, 2011 | 2004 Chrysler Sebring

1 Answer

I am getting a pulsing feeling from the front wheels when braking on my 2004 Chrysler Sebring. It feels like one or more of the rotors are warped. How do I replace the front rotors with new ones. Thanks.


If they are not worn beyond tollerance they can be machined on the vehicle.
Also make sure its not tyres or wheel bearings.

remove wheel
remove brake caliper( leave the hose connected)
remove centre cap
remove split pin and lock
unscrew bearing hub nut
rotor should come off
fit new bearing races in new rotor
grease new bearings
fit inside bearing and seal
refit rotor, outer bearing,washer,nut,lock, splitpin and centre cap
(tighten nut until no play in bearing plus 1\8 of a turn)
refit caliper and wheel
bleed and test brakes before driving

Apr 28, 2010 | 2004 Chrysler Sebring

1 Answer

Rubbing or humming sound while driving,louder when I drive faster, no shkes or shimmys while driving


Sounds like a bad wheel bearing. Listen for sound on one particular side Left Right or rear and front. Then the bearing will need to be replace to solve this problem. Good luck and thanks for using FIX YA.

Jun 17, 2009 | 2004 Chrysler Sebring

1 Answer

1995 chrysler sebring lxi


there are four 18mm bolts on the opposite side of dust plate.once u remove thoe bolts,you'll have to either use a slide hammer, or the old fashion way a big hammer and smack it side to side.the whole hub and wheel bearing assembly will come out.The dust sheild is in between the hub and axel once it comes apart u will understand.

Jun 02, 2008 | 1995 Chrysler Sebring

Not finding what you are looking for?
2004 Chrysler Sebring Logo

829 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...