Question about Dodge Ram 1500

1 Answer

Brakes the barake lights will not come on

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Dodge Master
  • 75,066 Answers

Test and replace brake switch as ness.

Posted on Sep 10, 2009


1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

ABS pulsing at low speed


Sounds like your brake rotors are warped.Take them to a machine shop and have them refinished or trued up.

Nov 28, 2011 | 2000 GMC Sierra

2 Answers

Are the front and rear brake pads the same or different sizes on my 2003 Silverado 1500 (4wd)?


YOU HAVE TO BUY FRONT PADS FOR FRONT BRAKES AND REAR PADS FOR REAR BRAKES THERE IS SOME DIFFERENCE.

Mar 04, 2011 | 2003 Chevrolet Silverado 1500

1 Answer

My 1994 Corolla has a problem with it's barake... when I'm driving they start to sieze up until I can not move forward. I have to either pull over for some time (varies) until they release or spray them...


u might be having a problem on the brake master. rubber caps must have been worn out. you have to replce the REPAIR KIT. make sure the repair kit is the same as the old one. geometry of the parts is very sensitve.

Oct 28, 2010 | 1994 Toyota Corolla

1 Answer

ABS light always on, I visually checked and cleaned all the sensrs, also checked the resistance of the sensors, all sensors reads 1.03 kohms. Reset the connectors on ABS control module, still ABS light...


cheeck the e brake cable or brakes in the rear see if the brake in the back look funny thin cheeck the front next time you drive it slam on the baraks pritty hard and let me now if you slide like the wheels lockt up or if the wheels did not lock up but stop the vehicle

Feb 28, 2010 | 1996 Jeep Grand Cherokee

2 Answers

2001 ford f150 supercrew 4x4......4 wheel drive will not engage???


There is a special sequence for that. Let me see if I can remember... Pull to a level surface, put the parking barake on, put the truck in neutral, shift to four-wheel drive, release the brake, shift to drive.

The computer waits for this sequence. It has been many years since I did this. If it doesnt work, call your dealer shop and they will tell you the correct sequence.

Dec 21, 2009 | 2001 Ford F150 Styleside SuperCrew

2 Answers

Fluid leaking from rear hand brake boot seal ford telstar


the rear caliper have allenkey screw..first open the cover scew that cover the allenkey. and than turn the allenkey srew to move the piston..
after piston coming out, the are clip to remove the piston holder..
than remove all the part and cleaned..after that install new oil seal for hand brake lavel.. mostly the leaking come from oil seal hand barake lavel.

Oct 11, 2009 | 1989 Mazda 626

3 Answers

Brake lights staying on.


switch behind break pedal is bad, replace switch

Sep 08, 2009 | 2000 Hyundai Elantra

2 Answers

1995 impreza doesn't always start, and when it does, takes awhile


The check engine light may be due to your o2 sensors. Your car may have a lot of mileage on it. Try replacing your front and rear o2 sensor. Subaru's tend to backfire because they run a bit rich from factory. If you could give us a check engine light code I can clarify what the problem is.

Mar 24, 2009 | 1995 Subaru Impreza

2 Answers

Converting built in infinity radio tuner to get european stations


Hi Barak, I have not seen an easy adjustment on any car stereo for converting the frequencies. The Crossfire stereo is manufactured by Becker. Try Becker of North America in Upper Saddle River NJ.

Nov 13, 2008 | 2006 Chrysler Crossfire

1 Answer

Troubleshooting 1984 chrysler back brake lights


There is a contact (not short) between wire to brake light and to back light on passenger side, when you press the pedal, electricity is absorbed by barake light bulb and back light dim out. Check cables and connectors, if necessary follow back cables to battery.
If the contact is a short the back lights fuse will blow, I think it is a contact between same polarity cables, not a short.

Regards

May 16, 2008 | 1984 Chrysler Fifth Avenue

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

356 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...